Nissan Rogue. Instruction — part 420
DLN-124
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
ELECTRIC CONTROLLED COUPLING
7. Temporarily tighten reamer bolts to the positions shown in the
figure.
8. Tighten reamer bolts and electric controlled coupling assembly
mounting bolts to the specified torque.
• For tightening torque, refer to
9. Install stud bolts .
CAUTION:
• Never reuse stud bolt.
• Screw long thread side of stud bolt to electric controlled
coupling.
• Screw the stud bolt until the stop by applying a torque of 15 N·m (1.5 kg-m, 11 ft-lb)
±20%.
• After installing stud bolt, the length of the protrusion from electric controlled coupling must be
19.8 mm (0.780 in)
±1.4 mm (0.055 in).
JSDIA5263ZZ
: Electric controlled coupling side
Thread length
A
: Long
B
: Short
JSDIA5237ZZ
DIFFERENTIAL ASSEMBLY
DLN-125
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
DIFFERENTIAL ASSEMBLY
Exploded View
INFOID:0000000011278420
Stud bolt
Connector bracket
Reamer bolt
Electric controlled coupling assem-
bly
Wave spring
Drive pinion oil seal
Drive pinion lock nut
Pinion front bearing
Gear carrier
Collapsible spacer
Drive pinion adjusting shim
Pinion rear bearing
Drive pinion
Drive gear
Differential case
Side bearing
Side bearing adjusting shim
Side oil seal
Rear cover
Stud bolt
Gasket
Drain plug
Filler plug
Pinion mate thrust washer
Pinion mate gear
Side gear thrust washer
Side gear
Pinion mate shaft
Lock pin
Oil seal lip
Screw hole
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
: Select with proper thickness.
: Apply gear oil.
*: Apply anti-corrosion oil.
: Apply multi purpose grease.
JSDIA5442GB
DLN-126
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
DIFFERENTIAL ASSEMBLY
Disassembly and Assembly
INFOID:0000000011278421
DISASSEMBLY
1. Remove drain plug, filler plug and gaskets.
2. Remove the side oil seal, using oil seal remover (commercial
service tool).
CAUTION:
Never damage gear carrier and rear cover.
3. Remove rear cover mounting bolts.
4. Set drifts (A and B) to the right and left side bearing adjusting
shims individually. Press differential assembly with side bearing
to remove gear carrier assembly and rear cover assembly.
CAUTION:
The pressure shall be as low as possible to remove gear
carrier assembly and rear cover assembly. The maximum
pressure shall be 10 kN (1 ton, 1.0 Imp ton).
NOTE:
Differential assembly, side bearings, and adjusting washers are
compressed and integrated in gear carrier and rear cover.
5. Remove stud bolt from rear cover.
NOTE:
It is not necessary to remove stud bolt except when it is replaced.
6. Remove side bearing adjusting shims and side bearing outer races.
CAUTION:
Mark the side bearing adjusting shims so that the original mounting positions (right/left) can be
identified later.
7. Remove side bearing inner races, using adaptor (A), separator
(B) and puller (C).
CAUTION:
• To prevent damage to the side bearing and drive gear,
place copper plates between these parts and vise.
• It is not necessary to remove side bearing inner race
except when it is replaced.
: Apply Genuine Silicone RTV or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
: Apply Genuine High Strength Thread Locking Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Products
PDG0216D
A
: Drift [SST: KV40100610 (J-26089)]
B
: Drift [SST: KV40100610 (J-26089)]
A
: Adaptor [ST33052000 ( — )]
B
: Separator (commercial service tool)
C
: Puller (commercial service tool)
JSDIA5286ZZ
JSDIA5287ZZ
DIFFERENTIAL ASSEMBLY
DLN-127
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
8. For proper reinstallation, paint matching marks on one differ-
ential assembly and drive gear.
CAUTION:
For matching marks, use paint. Never damage differential
assembly and drive gear.
9. Remove drive gear mounting bolts and then remove drive gear
from differential assembly.
10. Remove lock pin of pinion mate shaft, using the pin punch (com-
mercial service tool).
11. Remove pinion mate shaft.
12. Remove pinion mate gears, pinion mate thrust washers, side
gears, side gear thrust washers from differential case.
13. Perform inspection after disassembly. Refer to
ASSEMBLY
JSDIA5285ZZ
PDIA0759J
SDIA0031J
SDIA0032J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст