Nissan Rogue. Instruction — part 246
DAS
WARNING SYSTEMS SWITCH CIRCUIT
DAS-155
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
WARNING SYSTEMS SWITCH CIRCUIT
Diagnosis Procedure
INFOID:0000000011277318
Regarding Wiring Diagram information, refer to
.
1.
CHECK WARNING SYSTEMS SWITCH SIGNAL INPUT
1. Turn the ignition switch ON.
2. Check voltage between around view monitor control unit harness connector M113 terminal 17 and
ground.
Is the inspection result normal?
YES
>> Replace the around view monitor control unit. Refer to
DAS-173, "Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK WARNING SYSTEMS SWITCH
1. Turn ignition switch OFF.
2. Remove warning system switch.
3. Check warning system switch. Refer to
DAS-156, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the warning system switch. Refer to
DAS-174, "Removal and Installation"
3.
CHECK WARNING SYSTEM SWITCH GROUND CIRCUIT
Check continuity between warning system switch harness connector M253 terminal 8 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK WARNING SYSTEM SWITCH SIGNAL INPUT CIRCUIT FOR OPEN
1. Disconnect the around view monitor control unit control unit connector.
2. Check continuity between the around view monitor control unit harness connector M113 terminal 17 and
warning system switch harness connector M253 terminal 6.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair the harnesses or connectors.
Terminals
Condition
Voltage
(Approx.)
(+)
(
−)
AVM control unit
Ground
Warning systems switch
Connector
Terminal
M113
17
Pressed
0 V
Released
Battery voltage
Warning system switch
Ground
Continuity
Connector
Terminal
M253
8
Yes
Around view monitor control unit
Warning system switch
Continuity
Connector
Terminal
Connector
Terminal
M113
17
M253
6
Yes
DAS-156
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
WARNING SYSTEMS SWITCH CIRCUIT
5.
CHECK WARNING SYSTEM SWITCH SIGNAL INPUT CIRCUIT FOR SHORT
Check continuity between the around view monitor control unit harness connector M113 terminal 17 and
ground.
Is the inspection result normal?
YES
>> Replace the around view monitor control unit. Refer to
DAS-173, "Removal and Installation"
.
NO
>> Repair the harnesses or connectors.
Component Inspection
INFOID:0000000011277319
1.
CHECK WARNING SYSTEMS SWITCH
Check continuity of warning system switch.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace the warning system switch. Refer to
DAS-174, "Removal and Installation"
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M113
17
No
Warning system switch
Continuity
Terminal
Condition
6
8
When warning system switch is pressed
Yes
When warning system switch is released
No
DAS
WARNING SYSTEMS ON INDICATOR CIRCUIT
DAS-157
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
WARNING SYSTEMS ON INDICATOR CIRCUIT
Diagnosis Procedure
INFOID:0000000011277320
Regarding Wiring Diagram information, refer to
.
1.
CHECK WARNING SYSTEM ON INDICATOR POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect warning system switch connector M253.
3. Turn ignition switch ON.
4. Check voltage between warning system switch harness connector M253 terminal 5 and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the harness or connector.
2.
CHECK WARNING SYSTEMS ON INDICATOR SIGNAL FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect the around view monitor control unit harness connector M113.
3. Check continuity between the around view monitor control unit harness connector M113 terminal 15 and
warning system switch harness connector M253 terminal 3.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair the harnesses or connectors.
3.
CHECK WARNING SYSTEMS ON INDICATOR SIGNAL CIRCUIT FOR SHORT
Check continuity between the around view monitor control unit harness connector M113 terminal 15 and
ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair the harnesses or connectors.
4.
CHECK WARNING SYSTEMS ON INDICATOR
Check the warning systems ON indicator. Refer to
DAS-158, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace the around view monitor control unit. Refer to
DAS-173, "Removal and Installation"
.
NO
>> Replace warning systems switch.
DAS-174, "Removal and Installation"
.
Terminals
Voltage
(Approx.)
(+)
(
−)
Warning system switch
Ground
Connector
Terminal
M253
5
Battery voltage
Around view monitor control unit
Warning system switch
Continuity
Connector
Terminal
Connector
Terminal
M113
15
M253
3
Yes
Around view monitor control unit
Ground
Continuity
Connector
Terminal
M113
15
No
DAS-158
< DTC/CIRCUIT DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
WARNING SYSTEMS ON INDICATOR CIRCUIT
Component Inspection
INFOID:0000000011277321
1.
CHECK WARNING SYSTEMS ON INDICATOR
Apply battery voltage to warning system switch terminals 3 and 5, and then check if the warning systems ON
indicator illuminates.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace the warning systems switch. Refer to
DAS-174, "Removal and Installation"
Warning system switch
Terminals
Condition
Warning system switch ON indicator
(+)
(-)
5
3
When the battery voltage is applied
On
When the battery voltage is not applied
Off
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст