Nissan Frontier. Instruction — part 1291
ASSEMBLY
TM-375
< UNIT DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
45. Install mid carrier assembly in rear carrier assembly.
46. Install front carrier assembly, input clutch assembly and rear
internal gear as a unit.
47. Install seal rings in input clutch assembly.
CAUTION:
• Do not reuse seal rings.
• Apply petroleum jelly to seal rings.
48. Install band servo anchor end pin and lock nut in transmission
case.
CAUTION:
Do not reuse band servo anchor end pin.
49. Install brake band in transmission case.
CAUTION:
Install it so that the identification to avoid incorrect installa-
tion faces the servo side.
SCIA5017E
SCIA5015E
SCIA2470E
SCIA6512E
SCIA5498E
TM-376
< UNIT DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
ASSEMBLY
50. Install front sun gear to front carrier assembly.
CAUTION:
Apply ATF to front sun gear bearing and 3rd one-way clutch
end bearing.
51. Install needle bearing to front sun gear.
CAUTION:
Apply petroleum jelly to needle bearing.
52. Adjust brake band tilting using a clip so that brake band contacts
front sun gear drum evenly.
53. Adjust brake band.
a. Loosen lock nut.
b. Tighten band servo anchor end pin to specified torque.
c.
Back off band servo anchor end pin three turns.
d. Holding band servo anchor end pin, tighten lock nut to specified
torque.
Adjustment
INFOID:0000000009480705
TOTAL END PLAY
SCIA5014E
SCIA2808E
SCIA5033E
Anchor end pin
: 5.0 N·m (0.51 kg-m, 44 in-lb)
Lock nut
: 46 N·m (4.7 kg-m, 34 ft-lb)
SCIA5498E
ASSEMBLY
TM-377
< UNIT DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Measure clearance between front sun gear and bearing race for oil
pump cover.
• Select proper thickness of bearing race so that end play is within
specifications.
1. Measure dimensions “K” and “L” and then calculate dimension
“J”.
a. Measure dimension “K”.
b. Measure dimension “L”.
c. Calculate dimension “J”.
2. Measure dimensions “M
1
” and “M
2
” and then calculate dimen-
sion “M”.
SCIA2810E
SCIA5350E
SCIA5351E
“J”: Distance between oil pump fitting surface of
transmission case and needle bearing mating surface
of front sun gear.
J = K – L
SCIA5352E
SCIA3125E
TM-378
< UNIT DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
ASSEMBLY
a. Place bearing race and needle bearing on oil pump assembly.
b. Measure dimension “M
1
”.
c.
Measure dimension “M
2
”.
d. Calculate dimension “M”.
3. Adjust total end play “T
1
”.
• Select proper thickness of bearing race so that total end play
is within specifications.
SCIA3124E
SCIA3126E
SCIA3127E
“M”: Distance between transmission case fitting sur-
face of oil pump and needle bearing on oil pump.
M = M
1
– M
2
SCIA3125E
T
1
= J – M
Total end play “T
1
” : 0.25 - 0.55 mm (0.0098 - 0.0217 in)
Bearing races :Refer to
SCIA2810E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст