Nissan Frontier. Instruction — part 304
DLN-118
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
TRANSFER ASSEMBLY
39. Install the front oil seal until it is flush with the end face of the
front case, using Tool.
CAUTION:
• Do not reuse oil seal.
• Apply petroleum jelly to oil seal.
40. Align the matching mark on the front drive shaft with the mark on
the companion flange, then install the companion flange.
41. Install the companion flange self-lock nut. Tighten to the speci-
fied torque, using suitable tool. Refer to
.
CAUTION:
Do not reuse self-lock nut.
42. Install the O-ring to the transfer control device.
CAUTION:
• Do not reuse O-ring.
• Apply petroleum jelly to O-ring.
43. Install the transfer control device to the rear case.
a. Turn the control shift rod fully counterclockwise using a suitable
tool, and then put a mark on the control shift rod.
Tool number
: KV38100500 ( — )
PDIA0117E
SDIA2779E
WDIA0219E
SDIA3378E
PDIA0119E
TRANSFER ASSEMBLY
DLN-119
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
b. Align the transfer control device shaft cutout with the mark on
the control shift rod, and install it.
NOTE:
Turn the transfer control device when the transfer control device
connection does not match.
c. Tighten the bolts to the specified torque. Refer to
44. Install the drain plug and filler plug with new gaskets to the rear case. Tighten to the specified torque.
.
CAUTION:
Do not reuse gaskets.
PDIA0120E
SDIA2212E
DLN-120
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
PLANETARY CARRIER
PLANETARY CARRIER
Disassembly and Assembly
INFOID:0000000009479720
DISASSEMBLY
1. Remove the snap ring.
2. Remove the sun gear assembly from the planetary carrier
assembly using suitable tool.
3. Remove the snap ring from the sun gear assembly using suit-
able tool.
4. Remove the carrier bearing from the sun gear using Tools.
5. Remove the needle bearing from the sun gear using Tool.
SDIA2792E
SDIA2353E
Tool number
(A): ST35300000 ( — )
(B): ST30021000 (J-22912-01)
SDIA2149E
Tool number
: ST33710000 ( — )
SDIA2354E
PLANETARY CARRIER
DLN-121
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
6. Remove the metal bushing from the sun gear using Tools.
INSPECTION AFTER DISASSEMBLY
Bearing
Check the bearing for damage and rough rotation. If necessary,
replace the bearing with a new one.
Planetary Carrier
• Measure the end play of each pinion gear. If it is out of specifica-
tion, replace the planetary carrier assembly with new one.
• Check the working face of each gear and bearing for damage,
burrs, partial wear, dents and other abnormality. If any is found,
replace the planetary carrier assembly with a new one.
Sun Gear
• Check if the oil passage of the sun gear assembly is clogged. For
this, try to pass a 3.6 mm (0.142 in) dia. wire through the oil pas-
sage as shown.
• Check the sliding and contact surface of each gear and bearing for
damage, burrs, partial wear, dents and other abnormality. If any is
found, replace the sun gear assembly with a new one.
Internal Gear
Tool number
(A): ST33710000 ( — )
(B): ST35325000 ( — )
(C): ST33290001 (J-34286)
SDIA2168E
MTF0041D
Pinion gear end play
: 0.1 - 0.7 mm (0.004 - 0.028 in)
PDIA0146E
PDIA0147E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст