Nissan Maxima. Instruction — part 377
TRUNK LID
DLK-227
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
TRUNK LID ASSEMBLY : Adjustment
INFOID:0000000009471778
Check the clearance and the surface height between trunk lid and each part by visual inspection and tactile
feel.
1.
Trunk lid assembly
2.
Body side outer
3.
Rear combination lamp
4.
Rear bumper fascia
Front
AWKIA1553GB
DLK-228
< REMOVAL AND INSTALLATION >
TRUNK LID
If the clearance and the surface height are out of specification, adjust them according to the adjustment proce-
dures.
Unit: mm (in)
LONGITUDINAL CLEARANCE
Trunk Lid Removed From Hinge
1. Loosen the trunk lid to hinge bolts.
2. Move the trunk lid so that the clearance measurements are within specifications provided.
3. Tighten the trunk lid to hinge bolts.
Trunk Lid Hinge Removed From Vehicle
1. Remove the parcel shelf trim. Refer to
INT-28, "Removal and Installation"
.
2. Loosen the hinge to parcel shelf bolts.
3. Move the trunk lid so that the clearance measurements are within specifications provided.
4. Tighten the hinge to parcel shelf bolts.
5. Install the parcel shelf trim. Refer to
INT-28, "Removal and Installation"
SURFACE HEIGHT ADJUSTMENT
1. Loosen the bumper rubber.
2. Loosen the striker bolts.
3. Lift up the trunk lid approx. 100 - 150 mm (3.94 - 5.91 in) then close it lightly. Make sure it engages firmly
with the trunk lid closed.
4. Tighten the trunk lid striker.
TRUNK LID LOCK
TRUNK LID LOCK : Removal and Installation
INFOID:0000000009471779
LOCK
Removal
1. Remove the trunk lid finisher. Refer to
INT-36, "Removal and Installation"
2. Remove the trunk lid lock bolts.
3. Disconnect the harness connector and emergency release handle from the trunk lid lock and remove.
Installation
Installation is in the reverse order of removal.
STRIKER
Removal
1. Remove the trunk rear finisher. Refer to
INT-36, "Removal and Installation"
2. Remove the bolts and the striker.
Installation
Installation is in the reverse order of removal.
NOTE:
Align the trunk lid lock. Refer to
DLK-228, "TRUNK LID LOCK : Removal and Installation"
TRUNK LID STAY
Section
Item
Standard
Right/left clearance (MAX)
A – A
E
4.5
± 1.0 (0.18 ± 0.04)
≤2.0 (0.08)
F
-0.5
± 1.0 (-0.02 ± 0.04)
≤2.0 (0.08)
B – B
G
5.0
± 1.0 (0.20 ± 0.04)
≤2.0 (0.08)
H
-0.5
± 1.0 (-0.02 ± 0.04)
≤2.0 (0.08)
C – C
J
4.5
± 1.5 (0.18 ± 0.06)
≤2.0 (0.08)
D – D
K
7.0
± 2.0 (0.28 ± 0.08)
—
TRUNK LID
DLK-229
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
TRUNK LID STAY : Disposal
INFOID:0000000009471780
1. Fix trunk lid stay (1) using a vise (C).
2. Using hacksaw (A) slowly make 2 holes in the trunk lid stay, in
numerical order as shown.
CAUTION:
• When cutting a hole on trunk lid stay, always cover hack-
saw with a shop cloth (B) to avoid scattering metal frag-
ments or oil.
• Wear eye protection (safety glasses).
• Wear gloves.
JMKIA3336ZZ
A: 20 mm (0.8 in)
B: Cut at the groove.
JMKIA3609ZZ
DLK-230
< REMOVAL AND INSTALLATION >
DOOR SWITCH
DOOR SWITCH
Exploded View
INFOID:0000000009471781
Removal and Installation
INFOID:0000000009471782
REMOVAL
1. Remove the door switch screw (A).
2. Disconnect the harness connector from the door switch (1) and
remove.
INSTALLATION
Installation is in the reverse order of removal.
1.
Door switch
JMKIA2180ZZ
JMKIA2173ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст