Nissan Juke F15. Instruction — part 36
AV-130
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
U1010 CONTROL UNIT (CAN)
U1010 CONTROL UNIT (CAN)
NAVI CONTROL UNIT
NAVI CONTROL UNIT : DTC Logic
INFOID:0000000012202535
DTC DETECTION LOGIC
AROUND VIEW MONITOR CONTROL UNIT
AROUND VIEW MONITOR CONTROL UNIT : Description
INFOID:0000000012202536
CAN controller controls the communication of CAN communication signal and the error detection.
AROUND VIEW MONITOR CONTROL UNIT : DTC Logic
INFOID:0000000012202537
DTC DETECTION LOGIC
AROUND VIEW MONITOR CONTROL UNIT : Diagnosis Procedure
INFOID:0000000012202538
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Perform “All DTC Reading” with CONSULT.
3. Check if the “U1010” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “U1010” detected as the current malfunction?
YES
>> Replace the around view monitor control unit. Refer to
AV-190, "Removal and Installation"
NO
>> INSPECTION END
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible cause
U1010
CONTROL UNIT (CAN)
[Control unit (CAN)]
CAN initial diagnosis malfunction is detected.
Replace the NAVI control unit if the mal-
function occurs constantly.
Refer to
AV-182, "Removal and Installa-
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
U1010
CONTROL UNIT (CAN)
CAN initial diagnosis malfunction is detected.
Around view monitor control unit
AV
U111A REAR CAMERA IMAGE SIGNAL CIRCUIT
AV-131
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U111A REAR CAMERA IMAGE SIGNAL CIRCUIT
DTC Logic
INFOID:0000000012202539
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn the ignition switch ON.
2. Turn ignition switch OFF and wait at least 30 seconds.
3. Turn ignition switch ON and wait at least 30 seconds or more.
4. Select “Self Diagnostic Result” mode of “AVM” using CONSULT.
5. Check DTC.
Is DTC U111A detected?
YES
>> Refer to
.
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012202540
1.
CHECK CONTINUITY REAR CAMERA POWER SUPPLY AND GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit connector and rear camera connector.
3. Check continuity between around view monitor control unit harness connector and rear camera harness
connector.
4. Check continuity between around view monitor control unit harness connector and ground.
Is inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK VOLTAGE REAR CAMERA POWER SUPPLY
1. Connect around view monitor control unit connector and rear camera connector.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit harness connector and ground.
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
U111A
REAR CAMERA IMAGE
SIGNAL
Camera image signal circuit is open or shorted.
• Camera image signal circuit be-
tween rear camera and around
view monitor control unit
• Around view monitor control unit
• Rear camera
Around view monitor control
unit
Rear camera
Continuity
Connector
Terminals
Connector
Terminals
M98
17
D113
7
Existed
18
8
Around view monitor control
unit
Ground
Continuity
Connector
Terminal
M98
18
Not existed
AV-132
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
U111A REAR CAMERA IMAGE SIGNAL CIRCUIT
Is inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-190, "Removal and Installation"
3.
CHECK CONTINUITY CAMERA IMAGE SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit connector and rear camera connector.
3. Check continuity between around view monitor control unit harness connector and rear camera harness
connector.
4. Check continuity between around view monitor control unit harness connector and ground.
Is inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK CAMERA IMAGE SIGNAL
1. Connect around view monitor control unit connector and rear camera connector.
2. Turn ignition switch ON.
3. Check signal between around view monitor control unit harness connector.
Is inspection result normal?
Terminal
Condition
Standard
Reference voltage
(Approx.)
(+)
(
−)
Around view monitor control unit
Connector
Terminal
Connector
Terminal
M98
18
M98
17
“CAMERA” switch
(around view moni-
tor switch) is ON or
shift position is “R”.
3.5 V or more
6.0 V
Around view monitor control
unit
Rear camera
Continuity
Connector
Terminals
Connector
Terminals
M98
19
D113
1
Existed
20
5
Around view monitor control
unit
Ground
Continuity
Connector
Terminals
M98
19
Not existed
20
Terminal
Condition
Standard
Reference value
(+)
(
−)
Around view monitor control unit
Connector
Terminal
Connector
Terminal
M98
20
M98
19
Shift position is in
“R”.
Waveform accord-
ing to camera image
is input.
JSNIA0834GB
AV
U111A REAR CAMERA IMAGE SIGNAL CIRCUIT
AV-133
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
YES
>> Replace around view monitor control unit. Refer to
AV-190, "Removal and Installation"
NO
>> Replace rear camera. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст