Nissan Juke F15. Instruction — part 37
AV-134
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
DTC Logic
INFOID:0000000012202541
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn the ignition switch ON.
2. Shift the selector lever to “R” position.
3. Perform “All DTC Reading” with CONSULT.
4. Check if the “U111B” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “U111B” detected as the current malfunction?
YES
>> Refer to
.
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012202542
1.
CHECK CONTINUITY SIDE CAMERA RH POWER SUPPLY AND GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit connector and door mirror (passenger side) connector.
3. Check continuity between around view monitor control unit harness connector and door mirror (passenger
side) harness connector.
4. Check continuity between around view monitor control unit harness connector and ground.
Is inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK VOLTAGE SIDE CAMERA RH POWER SUPPLY
1. Connect around view monitor control unit connector and door mirror (passenger side) connector.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit harness connector and ground.
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
U111B
SIDE CAMERA RH IM-
AGE SIGNAL
Camera image signal circuit is open or shorted.
• Camera image signal circuit be-
tween side camera RH and around
view monitor control unit
• Around view monitor control unit
• Side camera RH
Around view monitor control
unit
Door mirror (passenger
side)
Continuity
Connector
Terminals
Connector
Terminals
M98
9
D9
6
Existed
10
14
Around view monitor control
unit
Ground
Continuity
Connector
Terminal
M98
10
Not existed
AV
U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
AV-135
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Is inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-190, "Removal and Installation"
3.
CHECK CONTINUITY CAMERA IMAGE SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit connector and door mirror (passenger side) connector.
3. Check continuity between around view monitor control unit harness connector and door mirror (passenger
side) harness connector.
4. Check continuity between around view monitor control unit harness connector and ground.
Is inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK CAMERA IMAGE SIGNAL
1. Connect around view monitor control unit connector and door mirror (passenger side) connector.
2. Turn ignition switch ON.
3. Check signal between around view monitor control unit harness connector terminals.
Is inspection result normal?
Terminal
Condition
Standard
Reference voltage
(Approx.)
(+)
(
−)
Around view monitor control unit
Connector
Terminal
Connector
Terminal
M98
10
M98
9
“CAMERA” switch
(around view moni-
tor switch) is ON or
shift position is “R”.
3.5 V or more
6.0 V
Around view monitor control
unit
Door mirror (passenger
side)
Continuity
Connector
Terminals
Connector
Terminals
M98
11
D9
7
Existed
12
15
Around view monitor control
unit
Ground
Continuity
Connector
Terminals
M98
11
Not existed
12
Terminal
Condition
Standard
Reference value
(+)
(
−)
Around view monitor control unit
Connector
Terminal
Connector
Terminal
M98
12
M98
11
Shift position is in
“R”.
Waveform accord-
ing to camera image
is input.
JSNIA0834GB
AV-136
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT
YES
>> Replace around view monitor control unit. Refer to
AV-190, "Removal and Installation"
NO
>> Replace side camera RH. Refer to
AV
U111C FRONT CAMERA IMAGE SIGNAL CIRCUIT
AV-137
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U111C FRONT CAMERA IMAGE SIGNAL CIRCUIT
DTC Logic
INFOID:0000000012202543
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn the ignition switch ON.
2. Shift the selector lever to “R” position.
3. Perform “All DTC Reading” with CONSULT.
4. Check if the “U111C” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “U111C” detected as the current malfunction?
YES
>> Refer to
.
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012202544
1.
CHECK CONTINUITY FRONT CAMERA POWER SUPPLY AND GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit connector and front camera connector.
3. Check continuity between around view monitor control unit harness connector and front camera harness
connector.
4. Check continuity between around view monitor control unit harness connector and ground.
Is inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK VOLTAGE FRONT CAMERA POWER SUPPLY
1. Connect around view monitor control unit connector and front camera connector.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit harness connector and ground.
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
U111C
FRONT CAMERA IM-
AGE SIGNAL
Camera image signal circuit is open or shorted.
• Camera image signal circuit be-
tween front camera and around
view monitor control unit
• Around view monitor control unit
• Front camera
Around view monitor control
unit
Front camera
Continuity
Connector
Terminals
Connector
Terminals
M98
5
E72
2
Existed
6
1
Around view monitor control
unit
Ground
Continuity
Connector
Terminal
M98
6
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст