Nissan Juke F15. Instruction — part 1342
TM-558
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
OIL PAN
2. Remove drain plug gasket .
3. Remove oil pan bolts (
).
4. Remove oil pan from transaxle case.
5. Remove oil pan gasket from oil pan.
6. Remove magnets from oil pan.
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never reuse oil pan gasket.
• Never reuse drain plug gasket.
• Never reuse O-ring.
• Completely clean the iron powder from the magnet area of oil pan and the magnets.
• Install the oil pan to the transaxle case with the following procedure.
1. Install the oil pan gasket to the oil pan.
CAUTION:
JSDIA5206ZZ
: Vehicle front
JSDIA5207ZZ
JSDIA7929ZZ
JSDIA7930ZZ
OIL PAN
TM-559
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Completely wipe out any moisture, oil, and old gasket from the oil pan gasket surface and bolt
hole of oil pan and transaxle case.
2. Install the oil pan assembly to the transaxle case, and then temporarily tighten the oil pan bolt.
3. Tighten the oil pan bolts in the order shown to the specified
torque.
4. Tighten the oil pan bolts again clockwise from (1) shown to the
specified torque.
• Fill with CVT fluid after installation. Refer to
.
Inspection
INFOID:0000000012201253
INSPECTION AFTER REMOVAL
Check oil pan for foreign material.
• If a large amount of worn material is found, clutch plate may be worn.
• If iron powder is found, bearings, gears, or clutch plates may be worn.
• If aluminum powder is found, bushing may be worn, or chips or burrs of aluminum casting parts may enter.
Check points where wear is found in all cases.
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid.
: Vehicle front
JSDIA5211ZZ
TM-560
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
INPUT SPEED SENSOR
INPUT SPEED SENSOR
Exploded View
INFOID:0000000012201254
Removal and Installation
INFOID:0000000012201255
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Turn ignition switch OFF.
2. Remove battery and battery support. Refer to
PG-105, "Removal and Installation"
.
3. Remove ECM and bracket as a set. Refer to
EC-1256, "Removal and Installation"
4. Disconnect input speed sensor connector.
5. Remove mounting bolt (
) and remove input speed sensor (1)
from transaxle assembly.
1.
Transaxle assembly
2.
O-ring
3.
Input speed sensor
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Apply CVT fluid
JSDIA6059GB
JSDIA6619ZZ
INPUT SPEED SENSOR
TM-561
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
6. Remove O-ring (1) from input speed sensor.
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to the O-ring.
Inspection and Adjustment
INFOID:0000000012201256
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid.
ADJUSTMENT AFTER INSTALLATION
If CVT fluid leaks during work, adjust the CVT fluid level. Refer to
.
JSDIA5196ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст