Nissan Juke F15. Instruction — part 629
EM-70
< UNIT REMOVAL AND INSTALLATION >
[MR FOR NISMO RS MODELS]
ENGINE ASSEMBLY
3. Remove drive shafts (RH and LH). Refer to
FAX-28, "2WD : Removal and Installation"
4. Remove rear torque rod (1). Refer to
5. Remove stabilizer connecting rod. Refer to
.
6. Rear front suspension member. Refer to
.
7. Preparation for the separation work of transaxle is as follows:
• Remove transaxle joint bolts which pierce at oil pan (upper) lower rear side. Refer to
.
Removal
1. Use a instruction lift table caddy (commercial service tool) (A) or
equivalently rigid tool such as a transmission jack. Securely sup-
port bottom of the engine and the transaxle assembly.
CAUTION:
Put a piece of wood or an equivalent as the supporting sur-
face, secure a completely stable condition.
2. Remove upper torque rod (RH) (1) and engine mounting insula-
tor (RH) (2).
3. Remove engine mounting insulator (LH).
4. Carefully lower jack, or raise lift to remove the engine and the transaxle assembly. When performing work,
observe the following caution.
CAUTION:
• Check that no part interferes with the vehicle side.
• Before and during this lifting, always check if any harnesses are left connected.
• During the removal, always be careful to prevent the vehicle from falling off the lift due to
changes in the center of gravity.
• If necessary, support the vehicle by setting jack or suitable tool at the rear.
Separation
1. Remove catalyst convertor. Refer to
2. Remove turbocharger. Refer to
3. Remove exhaust manifold. Refer to
.
2
: Rear torque rod bracket
: Vehicle front
JPBIA4417ZZ
PBIC3223J
: Vehicle front
JPBIA4419ZZ
ENGINE ASSEMBLY
EM-71
< UNIT REMOVAL AND INSTALLATION >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
4. Install engine slinger to front cover front left side (A) and cylinder
head rear right side (B).
5. Remove starter motor. Refer to
STR-27, "MR16DDT : Exploded View"
.
6. Lift with a hoist and separate the engine from the transaxle assembly. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never allow engine oil to get on engine mounting insulator. Be careful not to damage engine mount-
ing insulator.
• Check that each mounting insulator is seated properly, and tighten mounting nuts and bolts.
• When installation directions are specified, install parts according to the direction marks on them
referring to the figure of components. Refer to
.
AWD : Inspection
INFOID:0000000012197287
INSPECTION AFTER INSTALLATION
Inspection for Leakage
The following are procedures for checking fluids leakage, lubricates leakage, and exhaust gases leakage.
• Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to
MA-11, "Fluids and Lubricants"
• Use procedure below to check for fuel leakage.
- Turn ignition switch “ON” (with engine stopped). With fuel pressure applied to fuel piping, check for fuel leak-
age at connection points.
- Start engine. With engine speed increased, check again for fuel leakage at connection points.
• Run engine to check for unusual noise and vibration.
• Warm up engine thoroughly to check there is no leakage of fuel, exhaust gases, or any oil/fluids including
engine oil and engine coolant.
• Bleed air from lines and hoses of applicable lines, such as in cooling system.
• After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the
specified level, if necessary.
Summary of the inspection items:
*: Power steering fluid, brake fluid, etc.
: Engine front
Slinger bolts
Front cover front left
side:
: 32.9 N·m (3.4 kg-m, 24 ft-lb)
Cylinder head rear
right side:
: 25.0 N·m (2.6 kg-m, 18 ft-lb)
JPBIA4422ZZ
Items
Before starting engine
Engine running
After engine stopped
Engine coolant
Level
Leakage
Level
Engine oil
Level
Leakage
Level
Transmission /
transaxle fluid
AT & CVT Models
Leakage
Level / Leakage
Leakage
MT Models
Level / Leakage
Leakage
Level / Leakage
Other oils and fluids*
Level
Leakage
Level
Fuel
Leakage
Leakage
Leakage
Exhaust gases
—
Leakage
—
EM-72
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR FOR NISMO RS MODELS]
ENGINE STAND SETTING
UNIT DISASSEMBLY AND ASSEMBLY
ENGINE STAND SETTING
Setting
INFOID:0000000012197288
NOTE:
Explained here is how to disassemble with engine stand supporting transaxle surface. When using different
type of engine stand, note with difference in steps and etc.
1. Remove the engine and the transaxle assembly from the vehicle, and separate the transaxle from the
engine. Refer to
EM-64, "2WD : Removal and Installation"
(2WD models) or
(AWD models).
2. Install engine to engine stand with the following procedure:
a. Remove flywheel (M/T models) or drive plate (CVT models).
• Secure flywheel (M/T models) or drive plate (CVT models) (1)
with a stopper plate [SST: KV11105210 (J-44716)] (A), and
remove mounting bolts.
NOTE:
This figure shows CVT models as an example.
b. Remove pilot converter (1) (CVT models) or pilot bush (M/T
models) using pilot bushing puller [SST: ST16610001 (J-23907)]
(A) or suitable tool.
NOTE:
This figure shows CVT models as an example.
c.
Lift the engine with a hoist to install it onto widely use engine stand.
CAUTION:
• Use the engine stand that has a load capacity [approximately 135 kg (298 lb) or more] large
enough for supporting the engine weight.
• If the load capacity of stand is not adequate, remove the following parts beforehand to reduce the poten-
tial risk of overturning stand.
- Intake manifold: Refer to
- Catalyst converter: Refer to
(AWD models).
- Rocker cover: Refer to
NOTE:
JPBIA4425ZZ
PBIC3229J
ENGINE STAND SETTING
EM-73
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
The figure shows an example of widely used engine stand (A)
that can support mating surface of transaxle with flywheel (M/T
models) or drive plate (CVT models) removed.
CAUTION:
Before removing the hanging chains, check the engine
stand is stable and there is no risk of overturning.
3. Drain engine oil. Refer to
.
CAUTION:
Be sure to clean drain plug and install with new drain plug washer.
4. Drain engine coolant by removing water drain plug (1) from
inside of the engine.
Use Genuine RTV Silicon Sealant or equivalent. Refer to
22, "Recommended Chemical Products and Sealants"
.
PBIC3227J
: Engine front
Tightening torque
: Refer to
PBIC3228J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст