Nissan Juke F15. Instruction — part 1326
TM-494
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P0826 UP AND DOWN SHIFT SW
NO
>> Repair or replace damaged parts.
7.
CHECK GROUND CIRCUIT
Check continuity between CVT shift selector harness connector terminal and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Repair or replace damaged parts.
8.
CHECK PADDLE SHIFTER
1. Turn ignition switch OFF.
2. Disconnect paddle shifter connector.
3. Turn ignition switch ON.
4. Check voltage between paddle shifter side harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> GO TO 11.
9.
CHECK PADDLE SHIFTER
Check paddle shifter. Refer to
TM-496, "Component Inspection (Paddle Shifter)"
.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair or replace damaged parts.
10.
CHECK GROUND CIRCUIT
Check continuity between paddle shifter vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Repair or replace damaged parts.
11.
CHECK POWER SOURCE CIRCUIT
Check voltage between paddle shifter vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 12.
CVT shift selector
—
Continuity
Connector
Terminal
M57
10
Ground
Existed
Paddle shifter
Voltage (Approx.)
Connector
Terminal
M96
3
1
Battery voltage
M97
3
1
Paddle shifter
Ground
Continuity
Connector
Terminal
M96
1
Existed
M97
1
Paddle shifter
Ground
Voltage (Approx.)
Connector
Terminal
M96
3
0 V
M97
3
P0826 UP AND DOWN SHIFT SW
TM-495
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
NO
>> Repair or replace damaged parts.
12.
CHECK HARNESS BETWEEN PADDLE SHIFTER AND COMBINATION METER (PART 1)
1. Disconnect combination meter connector.
2. Check continuity between paddle shifter vehicle side harness connector terminals and combination meter
vehicle side harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> Repair or replace damaged parts.
13.
CHECK HARNESS BETWEEN PADDLE SHIFTER AND COMBINATION METER (PART 2)
Check continuity between paddle shifter vehicle side harness connector terminals and ground.
Is the inspection result normal?
YES
>> GO TO 14.
NO
>> Repair or replace damaged parts.
14.
DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
NO
>> Repair or replace damaged parts.
Component Inspection (Instruction Mode Switch)
INFOID:0000000012201192
1.
MANUAL MODE SWITCH
Check continuity between CVT shift selector connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace the CVT shift selector assembly due to malfunction in instruction mode switch. Refer to
546, "Removal and Installation"
Paddle shifter
Combination meter
Continuity
Connector
Terminal
Connector
Terminal
M96
3
M34
26
Existed
M97
3
5
Paddle shifter
Ground
Continuity
Connector
Terminal
M96
3
Not existed
M97
3
CVT shift selector
Condition
Continuity
Terminal
7 – 10
Instruction shift gate position (neutral)
Existed
Other than the above
Not existed
8 – 10
Selector lever: DOWN (
− side)
Existed
Other than the above
Not existed
9 – 10
Selector lever: UP (+ side)
Existed
Other than the above
Not existed
10 – 11
Instruction shift gate position
Not existed
Other than the above
Existed
TM-496
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P0826 UP AND DOWN SHIFT SW
Component Inspection (Paddle Shifter)
INFOID:0000000012201193
1.
CHECK PADDLE SHIFTER
Check continuity between paddle shifter connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace damaged parts.
Paddle shifter
Condition
Continuity
Terminal
1
3
Pressed paddle shifter (shift-up)
Existed
Released paddle shifter
Not existed
1
3
Pressed paddle shifter (shift-down)
Existed
Released paddle shifter
Not existed
P0841 TRANSMISSION FLUID PRESSURE SEN/SW A
TM-497
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P0841 TRANSMISSION FLUID PRESSURE SEN/SW A
DTC Logic
INFOID:0000000012201194
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1. Start the engine.
2. Drive the vehicle.
3. Maintain the following condition for 10 seconds or more.
CAUTION:
Also keep the accelerator pedal position constant.
4. Stop the vehicle.
5. Check the first trip DTC.
Is “P0841” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012201195
1.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace the transaxle assembly. Refer to
TM-577, "Removal and Installation"
.
NO
>> Repair or replace damaged parts.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible cause
P0841
FLUID PRESS SEN/SW A
(Transmission Fluid Pres-
sure Sensor/Switch “A” Cir-
cuit Range/Performance)
When all of the following conditions are sat-
isfied and this state is maintained for 5 sec-
onds:
• TCM power supply voltage: More than 11
V
• DTC other than the applicable DTC is not
detected.
• Primary pulley speed: 300 rpm or more
• Secondary pulley speed: 250 rpm or more
• Target speed for shifting: Less than 0.1
seconds
• Primary pulley pressure is outside the
specified value.
• Harness or connectors
(Secondary pressure sensor circuit is
open or shorted.)
• Harness or connectors
(Primary pressure sensor circuit is open
or shorted.)
• Secondary pressure sensor
Selector lever
: “D” position
Vehicle speed
: Constant speed of 40 km/h (25 MPH)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст