Nissan Juke F15. Instruction — part 130
C1144 INCOMPLETE STEERING ANGLE SENSOR ADJUSTMENT
BRC-111
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
C1144 INCOMPLETE STEERING ANGLE SENSOR ADJUSTMENT
DTC Logic
INFOID:0000000012199707
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
3. Perform self-diagnosis for “ABS”.
Is DTC “C1144” detected?
YES-1 >> “CRNT” is displayed: Proceed to
BRC-111, "Diagnosis Procedure"
YES-2 >> “PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012199708
1.
ADJUST THE NEUTRAL POSITION OF STEERING ANGLE SENSOR
Perform neutral position adjustment of steering angle sensor. Refer to
.
>> GO TO 2.
2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
With CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1144
ST ANG SEN SIGNAL
(Steering angle sensor not com-
plete)
When neutral position adjustment of steering angle sensor is not complete.
PAST DTC
CRNT DTC
Incomplete neutral position adjustment of steering angle sensor
• Harness or connector
• Steering angle sensor
• ABS actuator and electric unit (control unit)
• Incomplete neutral position adjustment of steering angle sensor
BRC-112
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC]
C1144 INCOMPLETE STEERING ANGLE SENSOR ADJUSTMENT
2. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
3. Perform self-diagnosis for “ABS”.
Is DTC “C1144” detected?
YES
>> GO TO 3.
NO
>> INSPECTION END
3.
CHECK STEERING ANGLE SENSOR SYSTEM
1. Turn the ignition switch OFF.
2. Check the steering angle sensor system. Refer to
BRC-108, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair / replace harness, connector, or terminal.
4.
CHECK DATA MONITOR
With CONSULT
1. “ABS”, “DATA MONITOR” and “STR ANGLE SIG” according to this order.
2. Check that the indication changes with the steering angle when the steering wheel is turned left/right from
the neutral position. Refer to
.
Is the inspection result normal?
YES
>> Replace the ABS actuator and electric unit (control unit). Refer to
.
NO
>> Replace the steering angle sensor. Refer to
C1155 BRAKE FLUID LEVEL SWITCH
BRC-113
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
C1155 BRAKE FLUID LEVEL SWITCH
DTC Logic
INFOID:0000000012199709
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
3. Perform self-diagnosis for “ABS”.
Is DTC “C1155” detected?
YES-1 >> “CRNT” is displayed: Proceed to
BRC-113, "Diagnosis Procedure"
YES-2 >> “PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012199710
1.
CHECK BRAKE FLUID LEVEL
1. Turn the ignition switch OFF.
2. Check the brake fluid level. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Refill brake fluid. Refer to
. GO TO 2.
2.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
1. Erase self-diagnosis result for “ABS”.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1155
BR FLUID LEVEL LOW
(Brake fluid level low)
• When brake fluid level low signal is detected.
• When an open circuit is detected in brake fluid level switch circuit.
PAST DTC
CRNT DTC
• Harness or connector
• Brake fluid level is low
• Harness or connector
• ABS actuator and electric unit (control unit)
• Brake fluid level switch
• Combination meter
• Brake fluid level is low
BRC-114
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC]
C1155 BRAKE FLUID LEVEL SWITCH
2. Turn the ignition switch OFF
→ ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
4. Perform self-diagnosis for “ABS”.
Is DTC “C1155” detected?
YES
>> GO TO 3.
NO
>> INSPECTION END
3.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Check the brake fluid level switch harness connector for disconnection or looseness.
3. Check the combination meter harness connector for disconnection or looseness.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair / replace harness or connector, and GO TO 4.
4.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
3. Perform self-diagnosis for “ABS”.
Is DTC “C1155” detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
CHECK BRAKE FLUID LEVEL SWITCH
Check the brake fluids level switch. Refer to
BRC-116, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace the reservoir tank. Refer to
BR-40, "Disassembly and Assembly"
. GO TO 6.
6.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
1. Erase self-diagnosis result for “ABS”.
2. Turn the ignition switch OFF
→ ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
4. Perform self-diagnosis for “ABS”.
Is DTC “C1155” detected?
YES
>> GO TO 7.
NO
>> INSPECTION END
7.
CHECK CONNECTOR AND TERMINAL
1. Turn the ignition switch OFF.
2. Disconnect brake fluid level switch harness connector.
3. Check the brake fluid level switch harness connector for disconnection or looseness.
4. Check the brake fluid level switch pin terminals for damage or loose connection with harness connector.
5. Disconnect combination meter harness connector.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст