Nissan Juke F15. Instruction — part 828
FRONT REGULATOR
GW-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
FRONT REGULATOR
Exploded View
INFOID:0000000012199897
Removal and Installation
INFOID:0000000012199898
REMOVAL
1. Remove the front door glass. Refer to
GW-17, "Removal and Installation"
.
2. Disconnect the power window motor harness connector and harness fixing clip.
3. Remove the regulator assembly mounting bolts.
4. Remove the regulator assembly from the door panel as shown
in the figure.
1. Front door panel
2.
Lower sash (front)
3.
Sealing screen
4.
Pull handle bracket
5.
Front door glass run
6.
Front door glass
7.
Power window motor
8.
Front door regulator assembly
9.
Lower sash (rear)
: Vehicle front
JMKIA5589ZZ
JMKIA5808ZZ
GW-20
< REMOVAL AND INSTALLATION >
FRONT REGULATOR
INSTALLATION
Install in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000012199899
DISASSEMBLY
Remove the power window motor from the regulator assembly.
INSPECTION AFTER REMOVAL
Check the regulator assembly for the following items. Replace or grease it if a malfunction is detected.
• Wire wear
• Regulator deformation
ASSEMBLY
Assemble in the reverse order of disassembly.
Inspection and Adjustment
INFOID:0000000012199900
SYSTEM INITIALIZATION
Initialize the system if any of the following work is complete. Refer to
FITTING INSPECTION
• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and guide rail
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.
REAR DOOR GLASS
GW-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR DOOR GLASS
Exploded View
INFOID:0000000012199901
Removal and Installation
INFOID:0000000012199902
REMOVAL
1. Fully open rear door glass.
2. Remove rear door finisher. Refer to
INT-16, "Removal and Installation"
.
3. Remove rear door speaker harness connector and the remove the sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
4. Remove the rear door outside molding.
5. Remove rear door glass run.
6. Operate the power window main switch or regulator handle to raise or lower the door window until the
glass mounting bolts can be seen.
7. Remove rear door glass mounting bolts.
1.
Rear door panel
2.
Sealing screen
3.
Lower sash (front)
4.
Rear door regulator assembly
5.
Power window motor
6.
Rear door glass
7.
Lower sash (rear)
8.
Rear door glass run
JMKIA5590ZZ
GW-22
< REMOVAL AND INSTALLATION >
REAR DOOR GLASS
8. Remove lower sash (rear) mounting bolts and TORX bolt with a
screwdriver (A) as shown in the figure.
9. Remove lower sash (rear) from the rear door panel.
CAUTION:
Avoid contact between lower sash (rear) and rear door glass when removing.
10. Remove rear door glass from the rear panel.
INSTALLATION
Install in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000012199903
SYSTEM INITIALIZATION
Initialize the system if any of the following work is complete. Refer to
.
FITTING INSPECTION
• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and guide rail
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.
JMKIA5591ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст