Nissan Juke F15. Instruction — part 1330
TM-510
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P0962 PRESSURE CONTROL SOLENOID A
NO
>> There is malfunction of line pressure solenoid valve. Replace transaxle assembly. Refer to
577, "Removal and Installation"
.
P0963 PRESSURE CONTROL SOLENOID A
TM-511
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P0963 PRESSURE CONTROL SOLENOID A
DTC Logic
INFOID:0000000012201210
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1. Start the engine and wait for 5 seconds or more.
2. Check the first trip DTC.
Is “P0963” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012201211
1.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT
1. Turn ignition switch OFF.
2. Disconnect TCM connector and CVT unit connector.
3. Check continuity between TCM harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts.
2.
CHECK CIRCUIT BETWEEN CVT UNIT AND GROUND
Check continuity between CVT unit harness connector terminal and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible causes
P0963
PC SOLENOID A
(Pressure Control Solenoid A
Control Circuit High)
When all of the following conditions are satis-
fied and this state is maintained for 0.2 sec-
onds:
• TCM power supply voltage: More than 11 V
• P0962 is not detected
• TCM judges that solenoid valve circuit is
open.
• Harness or connector
(Line pressure solenoid valve circuit is
open or shorted to power supply)
• Line pressure solenoid valve
TCM
CVT unit
Continuity
Connector
Terminal
Connector
Terminal
F83
30
F82
1
Existed
CVT unit
—
Condition
Resistance
Connector
Terminal
F250
1
Ground
CVT fluid temperature: 20
°C (68°F)
5.5 – 7.0
Ω
CVT fluid temperature: 50
°C (122°F)
6.0 – 8.0
Ω
CVT fluid temperature: 80
°C (176°F)
6.5 – 8.5
Ω
TM-512
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P0963 PRESSURE CONTROL SOLENOID A
NO
>> There is malfunction of line pressure solenoid valve. Replace transaxle assembly. Refer to
577, "Removal and Installation"
.
P0965 PRESSURE CONTROL SOLENOID B
TM-513
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P0965 PRESSURE CONTROL SOLENOID B
DTC Logic
INFOID:0000000012201212
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible causes
P0965
PC SOLENOID B
(Pressure Control Solenoid B
Control Circuit Range Perfor-
mance)
When any of 1 or 2 is satisfied and this state is
maintained for 10 seconds:
1.
When all of the following conditions are
satisfied:
-
DTC other than the applicable DTC is not
detected.
-
Engine speed: More than 625 rpm
-
Selector lever: Other than P/N position
-
CVT fluid temperature: More than -20
°C
(-4
°F)
-
TCM power supply: More than 11 V
-
The difference between instruction pres-
sure of primary pressure and 10-msec-
ago instruction primary pressure is 0
MPa or more
-
Instruction pressure of primary pressure:
0.86 MPa or more
-
Instruction pressure of primary pressure
- primary pressure: More than 1.2 MPa
-
When all of the following conditions are
satisfied and this state is maintained for
1 second:
•
DTC other than the applicable DTC is not
detected.
•
CVT fluid temperature: More than -20
°C
(-4
°F)
•
Selector lever: Other than P/N position
•
Engine speed: More than 625 rpm
•
Instruction pressure of primary pressure:
More than 2 MPa
•
Primary pressure: 0.4 MPa or less
2.
When all of the following conditions are
satisfied:
-
DTC other than the applicable DTC is not
detected.
-
CVT fluid temperature: More than -20
°C
(-4
°F)
-
Selector lever: Other than P/N position
-
TCM power supply: More than 11 V
-
When all of the following conditions are
satisfied and this state is maintained for
5.5 seconds:
•
DTC other than the applicable DTC is not
detected.
•
CVT fluid temperature: More than -20
°C
(-4
°F)
•
Selector lever: Other than P/N position
•
Primary pressure - instruction pressure
of primary pressure: 1.2 MPa or more
-
The difference between instruction pres-
sure of primary pressure and 10-msec-
ago instruction primary pressure is 0
MPa or more
-
Primary pressure - instruction pressure
of primary pressure: More than 1.2 MPa
• Harness or connector
(Primary pressure solenoid valve cir-
cuit is open or shorted.)
• Primary pressure solenoid valve
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст