Harley Davidson Softail Delux FLSTN BIKE 2011-2015. Service Manual — page 33
39
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-41137
HOSE CLAMP PLIERS
All Models
For tightening band type metal clamps on fuel
and oil lines.
HD-41182
FUEL PRESSURE GAUGE
Fuel Injected Models
(1995
1
⁄
2
& Later)
HD-41182 is a 0-100 psi fuel pressure gauge.
It comes with a special adapter that attaches to
the fuel lines of injected models for injector and
system pressure diagnosis.
1) J-34730-16A 90° Hose End Fitting
HD-41185
HOSE CUTTING TOOL
All Models
This is universal hose cutting tool.
It has a replaceable blade and will
cut hose diameters up to 1".
(Replacement Blade HD-41185-1)
HD-44061
FUEL PRESSURE GAUGE ADAPTER
All Models
Used with the HD-41182 Fuel Pressure Gauge
to check fuel pressure with “quick connect”
fuel lines.
HD-47114
FUEL TANK CONSOLE ALIGNMENT RING
XL 1200 Custom Models
This tool is used with a fuel tank filler cap to align
the replacement console on the fuel tank.
V-TWIN ENGINE/
Fuel System cont.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
40
HD-48030
FUEL INJECTION CLEANING KIT
All Fuel Injected Models
Clogged fuel injectors cause sluggish engine performance,
poor fuel economy and rough idle. This kit allows you to
easily correct these issues without replacing costly fuel
injectors. Use this as a money making tool during scheduled
maintenance procedures. Includes all adapters for Harley
and Buell Fuel Injected Models.
NOTE:
Fuel Injector Cleaner NOT included in Kit. Order
HD-48030-10.
1) HD-48030-30
Quick Disconnect
2) HD-48030-40
Fuel Fitting
3) HD-48030-50
Fuel Return Line Plug (Female)
4) HD-48030-60
Fuel Return Line Plug (Male)
5) HD-48030-70
Removal Tool
6) HD-49182-1
Fuel Tank Adapter
7) HD-48030-20
Fuel Injector Cleaner Canister
HD-48030-10
FUEL INJECTION CLEANING FLUID
All Fuel Injected Models
Used with HD-48030 to clean clogged fuel injectors.
NOTE:
This is not a fuel additive. Do not pour into
tank. Case of 12 cans. Use
1
⁄
2
can per engine.
HD-94752-77A
CARBURETOR FLOAT GAUGE
All Models
For setting carburetor float level.
HD-97087-65B
HOSE CLAMP PLIERS
All Models
These hose clamp pliers are smaller
than HD-41137 and can be used
in those hard to get at places.
V-TWIN ENGINE/
Fuel System cont.
41
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
B-45676
SPROCKET SHAFT SEAL INSTALLER
XL Models
(2004 & Later)
Used with HD-42579 to install replacement seals
to the correct depth. Buell dealers received this
XB9/XB12 Firebolt
tool in the XB9R essential program and will not
be shipped again.
HD-33428-A
BIG TWIN 4-SPEED MAIN DRIVE
Big Twin
GEAR BEARING INSTALLER
4-speeds
(1979 & Later)
Used with arbor press. Installs bearing in
transmission case to correct depth without
FX, FLH
damaging components.
HD-34761
SPORTSTER 4-SPEED CLUTCH
XL Models
SPRING COMPRESSOR
(1984
1
⁄
2
-1990)
Relieves diaphragm spring tension for removal
and installation.
HD-38362
SPORTSTER 5-SPEED
XL Models
SPROCKET LOCKING LINK
(1991-2003)
Locks engine sprocket and clutch shell for
Buell Models
sprocket and shaft nut and hub removal
(1995-2003)
and installation.
HD-38515-A
BIG TWIN/SPORTSTER CLUTCH DIAPHRAGM
1340 cc Models
SPRING COMPRESSOR
(1990-1997)
This tool is required for efficient servicing of the
XL Models
1340cc clutch. The compressor relieves spring
(1991 & Later)
pressure for disassembly during servicing.
Buell Models
1) HD-38515-1 Forcing Screw (1340cc)
(1995 & Later)
2) HD-38515-91 Forcing Screw (XL)
3) J-22825-BRG Bearing
4) J-23327-1
Bridge
5) J-28467-34
Handle
6) J-23444-A
Thread Lube
HD-41214
PRIMARY DRIVE LOCKING TOOL
All Big Twins
This tool is made from a special composition
plastic. It is used as a wedge type device to
hold the primary drive gear to allow the
technician to apply the proper torque without
damaging the primary gear.
V-TWIN DRIVE/TRANSMISSION/
Primary Drive/Clutch
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
42
HD-41496
MAIN DRIVE GEAR SEAL INSTALLER
All Models
(1994 & Later)
Used to install the large main drive gear seal.
HD-46283
PRIMARY DRIVE LOCKING TOOL
XL Models
(2004 & Later)
Securely locks the primary drive when removing
and torquing the motor sprocket and clutch hub
XB9/XB12 Firebolt
nuts with 38/57 ratios.
HD-47977
PRIMARY DRIVE LOCKING TOOL
Dyna Models
(2006 & Later)
Securely locks the primary drive when removing
and torquing the motor sprocket and clutch hub nut.
HD-48219
PRIMARY DRIVE LOCKING TOOL
FL/FX Models
(2007 & Later)
Securely locks the primary drive when removing
and torquing the motor sprocket bolt or clutch
hub nut.
HD-91042
CLUTCH HOLDING TOOL
XL Models
(1984 & Earlier)
When applying nut torque during reassembly
this tool is used to prevent the rotation of clutch
1340cc Models
shells and final drive sprockets (supersedes
(1984 & Later)
HD-97173-71 and HD-97175-55 clutch lock plates).
Used for early 1984 and earlier XL’s and late
1984 FL, FX and FLT’s.
HD-95650-42
MAINSHAFT STARTER CLUTCH AND
U
BEARING PULLER
FL
One end used to remove mainshaft starter clutch,
other end for pulling mainshaft ball bearing.
FX
HD-95960-52C
MULTI-PURPOSE PULLER
All Models
This tool supersedes HD-95960-52B &
HD-95960-41A. Pulls “wet clutch” using the
bolts from the clutch & pulls “dry clutch” using
clutch studs with standard nuts.
1) J-23444-A Thread Lube
V-TWIN DRIVE/TRANSMISSION/
Primary Drive/Clutch cont.
43
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-97178-71A
SPORTSTER 4-SPEED
XL Models
CLUTCH SPRING COMPRESSOR
(1971 & Early 1984)
Used to disassemble clutch.
XR
(1983-1984)
1) HD-97182-71 Stud (2)
2) HD-95964-52 Screw Seat
3) HD-97179-100 Support
HD-97200-55A
SPORTSTER 4-SPEED
XL
SPROCKET LOCKING LINK
XR
Locks engine sprocket and clutch sprocket teeth
(1957-1990)
to prevent rotation when nuts are removed or
installed.
HD-96385-78A
FORK SHIFTER GAUGE
Big Twin
4-speeds
Used to set and align transmission shifter forks on
(Mid 1979 & Later)
plate-type shifters.
B-45520
GEAR DETENT ASSEMBLY AID
XL Models
(2004 & Later)
Moves gear detent to permit crankcase reassembly.
Buell dealers received this tool in the XB9R essential
XB9/XB12 Firebolt
program and will not be shipped again.
V-TWIN DRIVE/TRANSMISSION/
Transmission Case
V-TWIN DRIVE/TRANSMISSION/
Primary Drive/Clutch cont.
V-TWIN DRIVE/TRANSMISSION/Shifter
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
44
B-45847
CROSS PLATE
XL Models
(2004 & Later)
Used with HD-35316-A to remove and install the
mainshaft 5th gear and roller bearing from the
XB9/XB12 Firebolt
right crankcase. Buell dealers received this tool
in the XB9R essential program and will not be
shipped again.
J-5586-A
TRANSMISSION SHAFT RETAINING
XL
RING PLIERS
XR
Installs new retaining rings on transmission shafts
without damage to rings or shaft.
All 5-speed Models
HD-34733
BIG TWIN 4-SPEED TRANSMISSION
4-speeds
COUNTERSHAFT GEAR BEARING INSTALLER
Big Twin Transmission
(1977 & Later)
When used with an arbor press, this tool installs
both needle bearings within the countershaft
gear to the correct depth. For all mid-1977 and
later 4-speed Big Twin transmissions.
HD-34734
EARLY BIG TWIN 5-SPEED MAIN DRIVE
5-speeds
GEAR BEARING AND SEAL INSTALLER
(1980-1990)
When used with an arbor press, one end of this
tool installs both the needle bearing on the
transmission side of the gear and the bearing
seal on the clutch side. The other end installs the
needle bearing on the clutch side.
HD-34735
BIG TWIN 4-SPEED TRANSMISSION
All
MAIN DRIVE GEAR BUSHING REMOVER
Big Twin
AND INSTALLER
4-speeds
When used with an arbor press, this tool
removes and installs the main drive gear bushing
quickly and easily. For all Big Twin 4-speed
transmissions.
HD-34810
SPORTSTER 4-SPEED TRANSMISSION
XL Models
MAINSHAFT BEARING INSTALLER
(Late 1984-1990)
The tool consists of a pilot and driver head.
When used with universal Driver Handle
HD-33416 (not included), HD-34810 will align
and install bearing without damage to case or
bearing.
1) HD-34810-1 Driver Head
2) HD-34810-2 Pilot
V-TWIN DRIVE/TRANSMISSION/
Transmission Case cont.
45
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-34902-B
BIG-TWIN MAINSHAFT PRIMARY BEARING
Big Twin
RACE REMOVER AND INSTALLER
(Late 1984 & Later)
1) HD-34902-1 Extender Shaft
2) HD-34902-2 Installer Sleeve
3) HD-34902-3B Puller Plate (improved B version for durability)
4) HD-34902-7 End Cap
5) J-7830-5
Bridge
6) J-21686-12
Forcing Screw
7) J-23444-A
Thread Lube
8) RS-9104-775 6" Bolt (2 Req’d)
9) 10258
Washer (2 Req’d)
HD-35316-C
5-SPEED & 6-SPEED MAIN DRIVE
5-Speed Big Twin
GEAR BEARING REMOVER & INSTALLER
(1980 & Later)
This tool will install Main Drive Gear Bearings for
XL Models
1980 and later 5-speed transmissions and will
(1991 & Later)
also install and remove the Main Drive Gear
from its bearing for all 5-speed models. It does all
Buell Blast
this without having to remove the transmission
(2000 & Later)
case from the motorcycle saving you time
and money.
Buell XB9R Firebolt
(2003 & Later)
1) HD-35316-1
Installer Cup
2) HD-35316-2
Bearing Driver
6-Speed Models
3) HD-35316-3A Cross Plate (Big Twin)
(2006 & Later Dynas)
4) HD-35316-4A 8" Bolt
(2007 & Later FL/FX)
5) HD-35316-5
12" Bolt
6) HD-35316-7
Washer
7) HD-35316-91 Cross Plate (XL)
8) 217801
Bearing
9) J-23444-A
Thread Lube
10) B-43983
Cross Plate (Blast)
11) B-45847
Cross Plate (Firebolt, XL - 2004 & Later)
12) HD-35316-8
Bearing Driver (6-Speed)
13) HD-35316-9
Bearing Driver (6-Speed)
14) HD-35316-10 Pilot (6-Speed)
15) HD-35316-11 Receiver Cup (6-Speed)
16) HD-35316-12 Installer Cup (6-Speed)
HD-35820
EVOLUTION SPORTSTER
XL Models
GEAR SPACING TOOL
Evolution
(1986 - 1990)
Aligns transmission shafts when performing
gear spacing.
HD-37404
SPORTSTER COUNTERSHAFT
XL Models
GEAR SUPPORT PLATE
(1991-2003)
Properly supports countershaft 4th gear
during countershaft removal.
V-TWIN DRIVE/TRANSMISSION/
Transmission Case cont.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
46
HD-37842-A
5-SPEED INNER AND OUTER MAIN DRIVE
Big Twin
GEAR NEEDLE BEARING INSTALLER
(1991 & Later)
Installs inner and outer mainshaft 5th gear
XL Models
needle bearing to correct depth.
(1991 & Later)
HD-39151
SPORTSTER SHIFT DRUM RETAINING
XL Models
RING INSTALLER
5-Speeds
(1991-2003)
Installs shift drum snap rings.
HD-39618
TRANSMISSION SHIFT PAWL ADJUSTER
5 Speed
(1992
1
⁄
2
- 2000)
Two pieces make up this tool. One is to loosen
the jam nut on the pawl adjuster, the other adjusts
the shifter pawl.
1) HD-39618-1
2) HD-39618-2
HD-41184
FINAL DRIVE TOOL
All Big Twin Models
(Belt Driven)
The Final Drive Tool HD-41184 is the
(1980 & Later)
one tool every technician must have.
It holds the Final Drive Sprocket so that
the technician can apply the proper torque
to the nut.
HD-41405
MAIN DRIVE GEAR SEAL INSTALLER
All 1340cc Models
5 Speed Models
HD-41405 is a two piece tool. It consists of
a seal protector and a seal driver. This tool
will install the main drive gear seal to the
proper depth without requiring removal
of the main drive gear from the mainshaft.
HD-42465
TRANSMISSION SHIFT PAWL ADJUSTER
FLSTS Heritage
Springer Models
Two pieces make up this tool. One to loosen
(1997 - 1999)
the jam nut on the pawl adjuster the other
adjusts the shifter pawl.
1) HD-42465-1
1
⁄
4
" Pawl Wrench
2) HD-42465-2
11
⁄
16
" Pawl Wrench
V-TWIN DRIVE/TRANSMISSION/
Transmission Case cont.
47
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-46282
FINAL DRIVE SPROCKET LOCKING TOOL
XL Models
(1991 & Later)
Secures belt sprocket when torquing sprocket
nut. Supersedes HD-42321. Also works on 1991
to 2003 XL models.
HD-46285
TRANSMISSION FIXTURE
XL Models
(2004 & Later)
Supports transmission shafts during assembly
into left crankcase.
XB9/XB12 Firebolt
1) HD-46285-1 Fixture Base
2) B-43985-1
Remover
3) B-43985-3
Installer
4) B-43985-4
Guide
HD-46288
MAINSHAFT LOCKNUT WRENCH
XL Models
(1991 & Later)
New short design removes and installs left-hand
thread mainshaft locknut without wrench slippage.
This short version is better suited for the Sportster
than the longer Big Twin tool, HD-94660-37B.
HD-47855
MAIN DRIVE GEAR NEEDLE
Buell Models
BEARING INSTALLER
(2006 & Later)
(except Blast)
Installs inner and outer main drive gear
needle bearings to correct depth.
XL Models
(2006 & Later)
HD-47856
MAIN DRIVE GEAR SEAL INSTALLER
Buell Models
(2006 & Later)
This is a six-piece tool including an installer
(except Blast)
(HD-47856-1), a pilot (HD-47856-2), two adapters
(HD-47856-3 & HD-47856-4), a nut (HD-47856-6)
Dyna Models
and a Crow's Foot Wrench (HD-47856-7). This tool
(2006 & Later)
is used to install the large main drive gear seal.
XL Models
(2006 & Later)
FL/FX Models
(2007 & Later)
HD-47910
MAINSHAFT LOCKNUT WRENCH
Dyna Models
(2006 & Later)
Removes and installs new larger right-hand
thread mainshaft locknut.
FL/FX Models
(2007 & Later)
V-TWIN DRIVE/TRANSMISSION/
Transmission Case cont.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
48
HD-47932
MAIN DRIVE GEAR NEEDLE
Dyna Models
BEARING INSTALLER
(2006 & Later)
Installs inner and outer main drive gear
needle bearings to correct depth.
HD-47933
MAIN DRIVE GEAR SEAL INSTALLER
Dyna Models
(2006 & Later)
This tool will install the small main drive gear seal
to the proper installed depth without requiring
removal of the main drive gear from the mainshaft.
HD-94660-37B
MAINSHAFT LOCKNUT WRENCH
1340 Models
(1984-1999)
This tool has been redesigned to accommodate
the longer mainshafts specified for 1984 and
Twin Cam 88/88B
later Big Twins. The two-piece design (pilot and
(2000 & Later)
wrench body) allows the technician to easily
remove the left hand thread mainshaft locknut
without wrench slippage.
1) HD-94660-1A Wrench Body
2) HD-94660-2
Pilot
HD-23738-A
MITY-VAC
®
HAND PUMP
All Models
Our most economical yet durable model. High
impact PVC; a self-lubricating, maintenance-free,
sealed, non-corrosive unit. Pumping rate of one
cu. in./stroke and attains a vacuum of 25 inches
of mercury in a few seconds.
HD-25070
HEAT GUN
All Models
This heat gun is universal and can be used
for many functions. It is especially handy
for sealing the silicone filled terminals that
are now being used to provide a waterproof
connection in crucial areas.
(Use with HD-41183 shown on page 34)
V-TWIN DRIVE/TRANSMISSION/
Transmission Case cont.
V-TWIN ELECTRICAL
49
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-26792
TEST SPARKPLUG
All Models
The HD-26792 checks for spark output without
removing spark plug from the engine.
HD-33813
INDUCTIVE TIMING LIGHT
All Models
Accurately times ignition systems. Features
a metal covered inductive pickup with a
heat resistant covering over the lead wire
for durability.
HD-35500-B
DIGITAL MULTIMETER (Fluke 23)
All Models
This multimeter provides the accuracy and features
of more expensive meters plus the convenience of
autoranging. Simply set the rotary switch to volts or
resistance and the HD-35500-A automatically sets the
required range.
HD-41334 RPM Inductive Pick-up
(optional accessory)
HD-35616-210
TEST LIGHT
All Models
Non-powered test light for voltage and continuity
checks. Banana jacks allow for easy connection to
terminal adapters in HD-41404-A Test Connector Kit.
HD-38125-6
PACKARD TERMINAL CRIMP TOOL
All Models
(1994 & Later)
This crimping tool is used for the sealed crimp
style Packard terminals. Instructions for use are
included with the tool.
HD-38125-7
PACKARD TERMINAL CRIMPER
All Models
(1994 & Later)
This crimping tool is used for the
non-sealing Packard terminals.
Dies for crimping are for A thru E.
Instructions for use are included.
HD-38125-8
PACKARD CRIMPING TOOL
All Models
(1994 & Later)
This crimping tool is used for the
non-sealing Packard terminals
F and G. Instructions included.
V-TWIN ELECTRICAL cont.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
50
HD-38625
CRUISE CONTROL TEST HARNESS
FL Ultra Model
(1989-1992)
Use to diagnose cruise control.
HD-39448-LNR
CB MICROPHONE & TRANSCEIVER
All Models with CB
LOAD DEVICE – LOANER TOOL
(1993-1997)
(This tool is no longer available for purchase.
It has been set up to loan as a service for
Harley-Davidson dealers.)
This tester is used in the diagnosis of CB pod
or transceiver failures. Includes CB Microphone
and Load Device.
HD-39448-3
CB POD ADAPTER
All Models with CB
(This tool is no longer available for purchase.
(1993-1997)
It has been set up to loan as a service for
Harley-Davidson dealers.)
This adapter is necessary to diagnose 1993 and
later CB radios. Used with HD-39448.
HD-39617
FLUKE AC/DC CURRENT PROBE
All Models
Used with HD-35500-A, HD-39978 & HD-39200
to measure current draw.
400A DC/400A AC
600 Volts Cat III
Output: 1 millivolt per ampere
HD-39621-A
TERMINAL REPAIR KIT
All Models
This kit includes a wide variety of replacement
Amp terminals and two special terminal release
tools, HD-39621-27 and HD-39621-28. For
terminal crimping use HD-38125-7 (not included).
HD-39621-28
PIN TERMINAL TOOL
All Models
HD-39621-27
SOCKET TERMINAL TOOL
Simplifies removal of Amp pin & socket type
terminals from terminal housing. Both included
in HD-39621-A Repair Kit.
V-TWIN ELECTRICAL cont.
51
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-39965
DEUTSCH TERMINAL CRIMP TOOL
All Models
This terminal crimping tool is specifically
designed to crimp the Deutsch connectors
that are now being used on all Harley-Davidson’s.
HD-39969
ULTRA-TORCH
All Models
Miniature butane torch HD-39969 can be used with
the shrink attachment for the new splice connectors.
Uniformly heats connectors all the way around to
insure a good seal.
HD-39978
DIGITAL MULTIMETER
All Models
(FLUKE 78)
The Fluke 78 provides many of the same features
as the more expensive Fluke meters at an
affordable price. You can measure frequency,
RPM, duty-cycle, dwell (direct reading),
temperature and Min/Max.
HD-41334 RPM Inductive Pick-up
(optional accessory).
HD-41183
HEAT SHIELD ATTACHMENT
All Models
This is an attachment that is designed
to be used in conjunction with the HD-25070
heat gun shown on page 31 for providing a
uniform heat source for sealing the new
silicone filled terminals.Its spoon shaped design
directs heat around the terminal to provide a
good flow of silicone.
HD-41334
RPM INDUCTIVE PICKUP
All Models
Allows Fluke Multimeter to be used
for RPM readings.
HD-41354
SPEEDOMETER TESTER
All Models with
Electronic Speedometers
This speedometer tester plugs into
the harness and can be used to read
inputs and outputs from the electronic
speedometer. It can also test the
calibration of the unit.
233570 Replacement Cable Assembly
V-TWIN ELECTRICAL cont.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
52
HD-41475
DEUTSCH TERMINAL REPAIR KIT
All Models
The HD-41475 is a complete set of Deutsch
terminals used on Harley-Davidson vehicles
organized in durable storage case
1) HD-41475-100 Flat Blade L-Hook
HD-41609
AMP MULTI-LOCK CRIMPER
All Models with
Multi-Lock Terminals
The HD-41609 is used to crimp the
(1996 & Later)
Multi-lock terminals.
HD-41771
ALTERNATOR ROTOR REMOVER & INSTALLER
FL Ultra
(1997 - 2006)
This tool removes and installs the alternator
rotor on the FL Ultra model.
Dyna Police
Models FXDP
(2002-2004)
HD-42376
BATTERY LOAD TESTER
All Models
A versatile volts-amps-load tester made especially
for troubleshooting power systems on motorcycles.
Inlcudes HD-42388 Battery Load Tester Stand.
HD-42879
ELECTRICAL CRIMP TOOL
FL
(1998 & Later)
This crimper is used for the Deutsch Solid
Barrel terminals.
HD-44608
RADIO BREAKOUT BOX
FL Radio
Equipped Models
This tool is designed to perform circuit diagnosis
(1998 & Later)
on the radio system.
HD-44695
TERMINAL CRIMPER
All Models Equipped
With Fuel Gauges
This crimper is used for the smaller
(2000 & Later)
multi-lock terminals.
V-TWIN ELECTRICAL cont.
53
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-45928
TERMINAL REMOVER
All Harley Models
Removes new Micro Pack 64 terminal from
connector without damage to connector body.
HD-45929
TERMINAL CRIMPER
All Harley Models
Securely crimps new Micro Pack 64 terminals
for wire harness repair procedures.
HD-45961
IGNITION SWITCH CONNECTOR REMOVER
FL
(2003 & Later)
Removes connector without damage to the switch.
VRSC
(2002 & Later)
HD-45962
IGNITION SWITCH ALIGNMENT TOOL
FL
(2003 & Later)
Aligns switch for installation.
VRSC
(2002 & Later)
HD-46601
BREAKOUT BOX ADAPTERS
XL & FX Models
(2004 & Later)
Used to connect HD-42682 Breakout Box
to speedometer and tachometer for
diagnostic service.
HD-47853
IGNITION SWITCH WRENCH
Dyna Models
(2006 & Later)
Used to remove and install new style
ignition switch.
HD-47918
ADVANCED AUDIO SYSTEM BREAKOUT BOX
FL Models
(2006 & Later)
Designed to perform circuit analysis on new
Advanced Audio System.
V-TWIN ELECTRICAL cont.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
54
HD-48037
SWR METER ADAPTERS
FL Models
(2003 & Later)
These adapters allow connection of SWR Meter
with PL-259 connectors to mate with the TNC
connector used on 2006 models.
HD-48053
ELECTRICAL SYSTEM ANALYZER
All Models
WITH WIRELESS PRINTER
Electrical Tester used for warranty reimubursement
on batteries in US and Canada. Also used to test the
starting and charging systems of the motorcycles.
1) HD-48053-10
Electrical System Analyzer w/o Wireless Printer
2) HD-48053-20
Wireless Printer
3) HD-48053-30
Replacement Test Leads
4) HD-48053-40
Printer Mounting Bracket (not pictured)
5) HD-48053-50
Rubber Protective Boot (not pictured)
6) HD-48053-60
Battery Warranty Bags
HD-48114
TERMINAL REMOVER
All Models
(2007 & Later)
Removes Molex terminal from connector without
damage to connector body.
HD-48119
TERMINAL CRIMPER
All Models
(2007 & Later)
This crimper is used for Molex terminals.
HD-94465-81
IGNITION TEST ADAPTER
All Models
(1980 & Later)
Connects into wiring harness for ignition system
troubleshooting using a volt/ohm meter.
HD-95715-19C
GENERATOR GEAR PULLER
G
Removes generator drive gears.
XL
1) HD-95635-46
Claw puller
FL
2) HD-95636-46
Center Cap
3) HD-95637-46A Bearing Separator
XR
4) J-23444-A
Thread Lube
V-TWIN ELECTRICAL cont.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст