Harley Davidson Softail Delux FLSTN BIKE 2011-2015. Service Manual — page 32
23
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-43984
CRANKSHAFT LOCKING TOOL
XL Models
(2000 & Later)
Tool will lock the crankshaft by engaging the
pinion gear splines. This permits the removal
and torquing of the pinion shaft nut.
HD-44062
BALANCER SHAFT RETENTION PINS
Twin Cam 88B
Tool secures the balancers during servicing of
counterbalancer components.
HD-44063
HYDRAULIC TENSION COMPRESSOR
Twin Cam 88B
Tool will compress the hydraulic tensioner assembly
to permit balancer chain removal.
HD-44064-A
BALANCER SHAFT SPROCKET
Twin Cam 88B
ALIGNMENT TOOL
Verifies proper alignment of the crankshaft and
balancer’s three sprockets.
HD-44065
CRANKCASE BEARING REMOVER & INSTALLER
Twin Cam 88B
(2000-2002)
Removes and installs the right crankcase
main bearing.
1) HD-44065-1
Installer
2) HD-44065-4
Base
HD-44066
BALANCER SHAFT INNER/OUTER
Twin Cam 88B
BEARING REMOVER & INSTALLER
Removes and installs the balancer’s inner & outer
support bearings.
1) B-43993-6
Installer
2) HD-44066-2
Cross Plate
3) HD-44066-4
Forcing Screw
4) HD-44066-5
Collet
5) J-23444-A
Thread Lube (not shown)
V-TWIN ENGINE/
Flywheel & Crankcase cont.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
24
HD-44069
TIMKEN SNAP RING REMOVER & INSTALLER
XL Models
(1977-2003)
Removes and installs the Timken outer race
snap ring in the left crankcase half.
HD-44358
FLYWHEEL SUPPORT FIXTURE
Twin Cam 88
(1999 & Later),
Used to support all straight crankpin
flywheels during servicing.
Twin Cam 88B
(2000 & Later),
1) HD-44358-1
Bracket
2) HD-44358-2
Hold Down Assembly
XL Models
3) HD-44358-3
Button (10-24 thread)
(2000 & Later)
4) HD-44358-8
Button (
3
⁄
8
-16 thread)
HD-44404
TIMKEN BEARING REMOVER
XL Models
(2000-2003)
Used with the HD-34902-B to remove the
inner Timken bearing from the flywheel.
HD-44408
HYDRAULIC TENSIONER RETAINERS
Twin Cam 88B
Secures the tensioner in a compressed position
during servicing.
HD-45206
SPROCKET SHAFT SEAL INSTALLER
XL Models
(2002-2003)
Installs sprocket shaft seal to the correct depth
in the crankcase without damage to the seal lip
and case bore. Used with the HD-42579 Sprocket
Shaft Bearing Installer.
HD-46287
LAPPING TOOL ADAPTER
XL Models
(2004 & Later)
Adapts HD-96710-40D for lapping of the
right main bearing outer race. Included in
XB12/XB9
HD-96710-40D Lapping Kit.
(2003 & Later)
V-TWIN ENGINE/
Flywheel & Crankcase cont.
25
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-46663
CRANKCASE BEARING REMOVER ADAPTER
XL Models
(2004 & Later),
Used with the HD-42720-5 Base and B-45655
Bearing Remover to remove the late style
XB9/XB12 Firebolt
crankcase bearing.
HD-47256
CRANKSHAFT ROTATING WRENCH
XL, Buell Models
Six splines engage the crankshaft to simplify
rotating the engine during service.
HD-47257
CRANKSHAFT ROTATING WRENCH
Twin Cam 88/88B
Ten splines engage the crankshaft to simplify
FL Models
rotating the engine during service.
(1999-2006)
FX Models
(2000-2006)
Dyna Models
(1999-2005)
HD-48283
CRANKSHAFT ROTATING WRENCH
Twin Cam 88/88B
24 splines engage the crankshaft to simplify rotating Dyna Models
the engine during service.
(2006 & Later)
FL/FX Models
(2007 & Later)
HD-48309
BALANCER BEARING INSTALLER
Big Twins
(2007 & Later)
Installs balancer and inner bearing as a single unit.
HD-48457
COUNTER BALANCER REMOVER
Big Twins
(2007 & Later)
Removes new style counter balancer.
V-TWIN ENGINE/
Flywheel & Crankcase cont.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
26
HD-48474
COUNTER BALANCER OUTER BEARING
Big Twins
REMOVER & INSTALLER
(2007 & Later)
Removes and installs outer bearing for new style
counter balancer.
HD-94461-81
CRANKCASE OIL PASSAGE DRILLING JIG
Big Twins
(1973-1980)
Replacement oil pumps have a relocated oil
passage outlet. This tool allows accurate drilling
of a matching passage into the crankcase for
proper engine oiling. Contains six mounting screws.
Two
1
⁄
4
- 24 screws for 1973 to 1975 models.
HD-94547-100
SPROCKET SHAFT BEARING RACE REMOVAL
Big Twins
& INSTALLATION TOOL
(1969-2002)
To remove and install engine sprocket shaft
bearing outer races from crankcase. Use with
HD-94547-102 Driver Handle.
HD-94547-101
SPROCKET SHAFT BEARING RACE
XL Models
REMOVAL & INSTALLATION TOOL
(1977-2003)
To remove and install engine sprocket shaft
bearing outer races from crankcase. Use with
HD-94547-102 Driver Handle.
HD-95715-19C
SPROCKET SHAFT EXTENSION AND
All Big Twins
BEARING PULLER
Used to remove sprocket shaft extension and
sprocket shaft Timken bearing inner race. Also
pulls front wheel speedometer drive gear.
1) HD-95635-46 Puller
2) HD-95637-46A Bearing Separator
3) HD-95636-46 Adapter
4) J-23444-A
Thread Lube
V-TWIN ENGINE
Flywheel & Crankcase cont.
27
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-96015-52
SPROCKET SHAFT TIMKEN BEARING
K, KH
INNER RACE PULLER
XL Models
Fits between sprocket shaft inner race and
(1976 & Earlier)
flywheel.
1) HD-96017-52 Puller Halves
2) HD-96018-52 Puller Collar
*Use with HD-33418 Universal Puller
Forcing Screw.
HD-96015-77B
SPROCKET SHAFT TIMKEN BEARING
XL Models
INNER RACE PULLER
(1977 - Early 1981)
Fits between sprocket shaft inner race and
flywheel.
1) HD-96017-77 Puller Halves
2) HD-96018-52 Puller Collar
*Use with HD-33418 Universal Puller Forcing Screw.
HD-96295-65D
TIMING MARK VIEW PLUG
All Models
The clear plastic plug threads into the crankcase
timing hole for accurate ignition timing with
strobe timing light, HD-33813. Allows easy viewing
without danger of getting oil all over.
HD-96650-80
FLYWHEEL TRUING STAND
All Models
Used to true crankshaft alignment. Measures and
indicates to .002"
1) Screw (not sold separately)
2) Screw (not sold separately)
3) Washer (not sold separately)
4) Nut (not sold separately)
5) Set of Indicators (not sold separately)
6) HD-96652-19 Stationary Center (sold separately)
7) HD-96660-41 Moveable Center (sold separately)
V-TWIN ENGINE
Flywheel & Crankcase cont.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
28
HD-96710-40D
CRANKCASE MAIN BEARING LAPPING TOOL
All Models
For aligning right and left main bearing races
and lapping. Also used to lap pinion shaft
bearing race on engines with Timken bearings.
1) HD-96710-51
Collar Spanner Wrenches
2) HD-96712-40A Lapping Arbor
3) HD-96718-40A Lap, 1
3
⁄
8
"
4) HD-96718-58A Lap, 1
3
⁄
4
"
5) HD-96719-40A Nut
6) HD-96719-87
Spacer
7) HD-96720-40A Collar
8) HD-96720-87
Adapter Sleeve
9) HD-96721-40A Collar
10) HD-96721-87A Lap, 1
5
⁄
8
"
11) HD-96722-40A Nut
12) HD-96728-56A Guide Sleeve & Sleeve Nut
13) HD-96727-56A Guide Sleeve & Sleeve Nut
14) HD-96710-50
Handle Assembly
15) HD-96719-87
Spacer XL (1987-2003)
16) HD-96720-87
Adapter Sleeve XL (1987-2003)
17) HD-96721-87A Lap, 1
5
⁄
8
" XL (1987-2003)
18) HD-46287
Lapping Tool Adapter XL (2004 & Later),
XB12/XB9 (2003 & Later)
HD-97225-55C
SPROCKET SHAFT BEARING INSTALLER
For installing flywheel assembly into crankcase
Big Twins
Timken bearing.
(1955 & Later)
Presses main bearing into inner race to
Dyna Models
correct depth.
(2006 & Later)
1) HD-97227-55A
Screw
FL/FX Models
2) HD-97228-55A
Collar
(2007 & Later)
3) RS-25100-300
Bearing
4) 212434
Washer
5) HD-97229-55
Handle
6) J-23444-A
Thread Lube (not shown)
7) HD-97225-1
Sprocket Shaft Adapter
8) HD-97225-2
Collar
B-45523
VALVE GUIDE REAMER (7mm)
XL Models
(2004 & Later)
Reams replacement intake and exhaust valves
guides to the proper size.
XB9/XB12 Firebolt
V-TWIN ENGINE
Flywheel & Crankcase cont.
V-TWIN ENGINE/Camshaft,
Valves & Valve Train
29
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
B-45524-A
VALVE GUIDE REMOVER / INSTALLER (7mm)
XL Models
(2004 & Later)
Removes worn guides and installs replacement
guides to the correct height.
XB9/XB12 Firebolt
1) B-45524-1
Remover
2) B-45524-2A Installer
B-45525
VALVE GUIDE HONE (7mm)
XL Models
(2004 & Later)
Applies final surface finish and crosshatch
to replacement guides.
XB9/XB12 Firebolt
HD-33443
BIG TWIN TAPPET GUIDE ALIGNMENT TOOL
1340cc
Evolution
This tool aligns the tappet guides to the engine
case. The result is proper alignment of the cam
lobes to the valve tappets. (1340cc Evolution only).
HD-33871
SPORTSTER VALVE GUIDE INSTALLER
XL Models
(1957-1985)
Installs shoulderless valve guides to correct depth.
*Use with HD-34740 Driver & Remover Handle.
HD-34107
VALVE GUIDE DEPTH/CUTTING TOOL
All Shovelhead Models
Obtains proper clearance between exhaust valve
head and guide.
HD-34199-A
PUSHROD HEIGHT GAUGE
All Evolution Models
(1984-1990)
This tool allows the technician to quickly
and accurately determine the proper size
push rod when servicing the valve train.
Used in conjunction with HD-34199-86 for
XL Evolution.
HD-34199-86
PUSHROD HEIGHT GAUGE ADAPTER
XL Models
(1986-1990)
This tool when used with HD-34199 (previously
essential) allows the technician to quickly and
accurately determine the proper size pushrod
when servicing the valve train.
V-TWIN ENGINE/Camshaft,
Valves & Valve Train cont.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
30
HD-34641
FXST REAR INTAKE VALVE SPRING
All Softail Models
COMPRESSOR
This tool compresses intake valve spring on the
rear cylinder of the FXST so that the rocker box
can be removed while the engine is still in the
frame. It does this without damage to the valve
stem, valve spring, or rocker cover.
HD-34643-A
EVOLUTION SHOULDERLESS VALVE
All EVO
GUIDE SEAL INSTALLER
(1984 & Later)
This tool installs the valve guide seals securely
Twin Cam 88/88B
without damage to the seal itself on all
(2000-2004)
Evolution models.
HD-34723
8mm VALVE GUIDE FLEX HONE
XL Models
Evolution - All
Used to properly finish valve guides (.315).
The hone is made of 180 grit silicon carbide
Twin Cam 88/88B
to ensure a smooth finish.
HD-34724-A
10mm VALVE GUIDE FLEX HONE
All Shovelhead Models
Used to properly finish valve guides (.394).
The hone is made of 180 grit silicon carbide
to ensure smooth finish.
HD-34731
EVOLUTION VALVE GUIDE INSTALLER
All EVO Models
(1984 & Later)
This tool takes the guesswork out of valve guide
installation and insures that the guide is installed
Twin Cam 88/88B
to the proper depth on all Evolution models.
(2000-2004)
HD-34736-B
VALVE SPRING COMPRESSOR
All Models
Compresses valve springs on all cylinder
heads. Forcing screw design allows gradual,
controlled compressing.
V-TWIN ENGINE/Camshaft,
Valves & Valve Train cont.
31
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-34740
VALVE GUIDE & VALVE GUIDE SEAL HANDLE
All XL Models
(1957 & Later)
Use to remove shoulderless valve guides on
XL’s and the Evolution engine. (Also used as
driver for HD-33871, HD-34643, HD-34731,
and HD-35103.)
HD-34751
VALVE GUIDE CLEANING BRUSH
All Models
Hand held
1
⁄
2
" dia. nylon brush for cleaning
valve guides after honing.
HD-35103
BIG TWIN VALVE GUIDE SEAL INSTALLER
All Shovelhead Models
This tool installs the valve guide seals to proper
height without damage. For all Shovelheads.
Use with HD-34740 Handle.
HD-35758-C
NEWAY VALVE SEAT CUTTER SET
All Models
HD-35758-C is approved and recommended by
the Harley-Davidson Service Department. This
special cutter set is reasonably priced and consists
of one of each of the following Neway part numbers.
Includes:
Neway No.
Description
622
Cutter, 1
1
⁄
2
" dia. (31° x 46°)
205
Cutter, 1
1
⁄
2
" dia. (60°)
293
Cutter, 1
3
⁄
4
" dia. (60°)
642
Cutter, 1
3
⁄
4
" dia. (31° x 46°)
140-5⁄16
Solid Pilot -
5
⁄
16
" dia. -3, -2, -1, Std., +1
140-11⁄16
Solid Pilot -
11
⁄
32
" dia. -4, -3, -2, -1 Std., +1
140-3⁄8
Solid Pilot -
3
⁄
8
" dia. -2, -1, -2, Std., +1, +2, +3, +4
503
T-Wrench
160
Molded Storage/Carrying Case
14060
HD-35758-51 6mm Pilot
203
HD-35758-53 Exhaust Seat Cutter, 1
1
⁄
4
dia. (31° x 46°)
271
HD-35758-54 Intake Seat Cutter, 1
1
⁄
2
dia. (70°)
PM140702
B-35758-52A 7mm Pilot
HD-35759
NEWAY MODEL 1700 POWER HEAD
All Models
Features Include:
*115V, 60 RPM Drive
*Used with HD-35761, Track Mounted
Headstand and HD-35758 Cutter Set
V-TWIN ENGINE/Camshaft,
Valves & Valve Train cont.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
32
HD-35760
BENCH MOUNT HOLDING FIXTURE
All Models
For hand or stone cutters. Used with HD-35758
Cutter Set.
HD-35761
TRACK MOUNT HOLDING FIXTURE
All Models
For use with HD-35759 Neway Power Head &
HD-35758 Cutter Set.
HD-38361
CAM GEAR GAUGE PIN SET .108"
1340cc Models
(1990 & Later)
Used to measure and verify cam gear sizes
and color coding.
XL Models
(1991 & Later)
HD-39847
RATCHETING TAP HANDLE
All Models
This is a universal ratcheting tap handle.
Also works extremely well with reamers.
HD-39932
VALVE GUIDE REAMERS
HD-39933
HD-41201
These reamers are used to finish ream newly
installed valve guides.
1) a.
HD-39932
Spiral Flute
High Speed Steel
EVO All/Iron XL INT (1957-1985)
Twin Cam 88/88B (2000-2004)
1)
b.
HD-39932-CAR
Spiral Flute
Carbide
EVO All/Iron XL INT (1957-1985)
Twin Cam 88/88B (2000-2004)
2) a.
HD-39933-INT
Spiral Flute
High Speed Steel
Shovelhead Intake
1)
b.
HD-39933-INT-CAR
Spiral Flute
Carbide
Shovelhead Intake
3) a.
HD-39933-EXH
Spiral Flute
High Speed Steel
Shovelhead Exhaust
1)
b.
HD-39933-EXH-CAR
Spiral Flute
Carbide
Shovelhead Exhaust
4) a.
HD-41201
Spiral Flute
High Speed steel
Iron XL Exhaust (1957-1985)
1)
b.
HD-41201-CAR
Spiral Flute
Carbide
Iron XL Exhaust (1957-1985)
NOTE: Carbide reamers can be resharpened.
V-TWIN ENGINE/Camshaft,
Valves & Valve Train cont.
33
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-42313
CAM CHAIN TENSIONER UNLOADER
Twin Cam 88/88B
Removes cam chain tensioner pressure
from cam chain during disassembly
and reassembly.
1) HD-42313-1 Tensioner Unloader
2) HD-42313-2 Retaining Pin (1 pin)
HD-42314
CAMSHAFT/CRANKSHAFT
Twin Cam 88/88B
SPROCKET LOCKING TOOL
Locks camshaft/crankshaft sprockets
during disassembly & reassembly to
permit proper torquing.
HD-42325-A
CAMSHAFT NEEDLE BEARING
Twin Cam 88/88B
REMOVER & INSTALLER TOOL
Used to remove and replace the camshaft’s
two inner needle bearings.
1) HD-42325-3
Removal Collet
2) HD-42325-5
Plate Assembly
3) HD-42325-6
Installer
4) HD-42325-7
Installer Forcing Screw
5) HD-42325-8
Thumb Screw (4 required)
6) 10213
Hex Nut
7) 13324
Washer
8) 15427
Bearing
9) J-23444-A
Thread Lube
10) HD-52325-12 Removal Collet (1”)
11) HD-52325-13 Installer (1”)
HD-42928
CAMSHAFT NEEDLE BEARING
FX
REMOVING & INSTALLING TOOL
FL, FLT
Used to remove and install camshaft needle bearings.
(1958-1999)
1) HD-42928-1 Plate
2) HD-42928-2 Remover
3) HD-42928-3 Installer
4) HD-42928-4 Thumb Screw (3 req’d)
V-TWIN ENGINE/Camshaft,
Valves & Valve Train cont.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
34
HD-43419
GIZMATIC 3
Universal
Uses tungsten carbide cutters to machine the valve face.
This unique tool allows quick resurfacing of valves by
hand. The high and low spots common to traditional
valve grinding equipment are virtually eliminated.
Grinding valves leaves a crosshatch pattern on the valve
face which is not the optimum surface for valve-to-head
seating. The Gizmatic-3 leaves a concentric pattern on
the valve face. This is the best surface for proper valve
seating in the head. Use Gizmatic-3 for the valves and
the HD-35758-B Valve Seat Cutter Set for the heads.
HD-43644
CAMSHAFT REMOVER & INSTALLER
Twin Cam 88/88B
This three piece tool is used to remove and
install front and rear cylinder camshafts and
install bearings in the support plate.
1) HD-43644-1 Camshaft Remover/Installer
2) HD-43644-2 Bearing Support Plate
3) HD-43644-3 Bearing Installer
HD-46583
VALVE GUIDE INSTALLER
103 cu. in. Powertrains
Presses replacement valve guides to the correct
height in 103 cu. in. models.
HD-46584
VALVE GUIDE SEAL INSTALLER
103 cu. in. Powertrains
Installs replacement valve guide seals to the
correct installed height in 103 cu. in. models.
HD-47248
LOWER ROCKER BOX WRENCH
Twin Cam 88/88B
Permits easy access to fasteners when servicing
XL, Buell Models
the lower rocker box.
HD-47250
INTAKE MANIFOLD WRENCH
All Models
Used for easy access to remove and install the
intake manifold fasteners.
HD-47258
UPPER ROCKER BOX WRENCH
All Models
Permits easy access to fasteners with engine in
chassis when servicing the upper rocker cover.
V-TWIN ENGINE/Camshaft,
Valves & Valve Train cont.
35
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-47941
CAMSHAFT LOCKING TOOL
Dyna Models
(2006 & Later)
Locks camshaft/crankshaft sprockets during
disassembly and reassembly to permit proper
torquing.
HD-47956
CAMSHAFT ASSEMBLY TOOL
Dyna Models
(2006 & Later)
HD-47956 is a three-piece tool including a 1.5"
Guide (HD-47956-1), a 1.35" Guide (HD-47956-2),
and a Support Plate (HD-47956-3). The tool is used
to hold the camshafts and secondary cam chain while
the cam support plate is installed on the camshafts.
HD-94438-79
HYDRAULIC LIFTER GAUGE
All Shovelhead Models
Used to check pushrods for correct adjustment.
HD-94802-36A
CAM GEAR SHAFT BUSHING
FL
REAMER–.812 DIA.
(1969 & Earlier)
Used to fit cam gear shaft bushings.
HD-94803-67
REAR INTAKE CAMSHAFT COVER
G
BUSHING REAMER—1.125 DIA.
XL
For reaming timer shaft bushings in gear case cover.
XR
HD-94804-57
ROCKER ARM BUSHING REAMER–.555 DIA.
XL
Used to line ream replacement rocker arm
FL
bushings to size.
FLT
FX
HD-94812-77A
PINION SHAFT BUSHING REAMER
XL Models
AND PILOT
(1977 & Later)
Reams pinion shaft bushing in gear cover.
1) HD-94812-1 Reamer .563 dia.
2) HD-94812-2 Pilot (1977-1986)
3) HD-94812-87 Pilot (1987-Later)
V-TWIN ENGINE/Camshaft,
Valves & Valve Train cont.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
36
HD-95632-79
CAM GEAR GAUGE PIN SET .105"
All Models
Used to select proper cam gear size and verify
color coding.
HD-96550-36A
VALVE LAPPING TOOL
All Models
Suction cup secures to valve head while
lapping.
HD-96796-47
VALVE SPRING TEST FIXTURE
All Models
Has adjustable platform for various length
springs. A tone device indicates when to read
scale. Used with torque wrench (not included).
HD-97102-81
VALVE LIFTER REMOVER
All Shovelhead Models
Simplifies removal of loctited hydraulic valves.
HD-97273-60
CAMSHAFT NEEDLE BEARING
XL Models
INSTALLER
(1957-1990)
Used to install camshaft needle bearings.
*Use with HD-33416 Driver Handle.
HD-44455
OIL LINE REMOVER/OIL LINE
Softail Models
RETAINER INSTALLER
(2000 & Later)
Removes oil lines and installs replacement
retainer clips.
V-TWIN ENGINE/Camshaft,
Valves & Valve Train cont.
V-TWIN ENGINE/Gearcase
37
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-94555-55C
PINION GEAR SHAFT NUT SOCKET
All Big Twins
(1954-1992)
Fits pinion gear nut which secures pinion to
gear shaft.
HD-94805-57
PINION SHAFT BUSHING REAMER AND
FLT, FX
TWO PILOTS
FL Models
Used to size pinion shaft gear case cover bushing
(1964 & Later)
on FL, FLT, FX and idler gear bushing on XL.
XL Models
1) HD-94806-57 .562 Dia. Reamer
2) HD-94815-58 Reamer Pilot
(1964 & later–FL, FLT and FX)
3) HD-94807-57 Reamer Pilot (XL)
HD-96295-65D
TIMING MARK VIEW PLUG
All Models
Clear plastic plug threads into crankcase timing
hole for accurate ignition timing with strobe
timing light.
HD-96830-51B
PINION GEAR PULLER AND COLLARS
All Big Twins
(1954 -1989)
Used to remove and install pinion gear.
1) HD-96831-51A Screw Assembly
2) HD-96836-57 Collar (G, XL, K, KH)
3) HD-96836-51 Collar (FL, FLT, FX)
4) HD-96832-51A Body
5) HD-96830-100 Nut
6) J-23444-A
Thread Lube
HD-96921-52C
OIL PRESSURE GAUGE SET
All Models
A complete oil pressure tester that includes
adapters for V-Twin applications. The tool checks
oil pump pressure under operating conditions.
Gauge is graduated 0-60 psi. Includes adapters:
1) HD-96921-100A Gauge Assembly
2) HD-96940-53
Banjo Bolt
3) HD-96921-120
Twin Cam 88B
4) HD-96921-110
Twin Cam 88
5) HD-96921-106
1/2-20 Threaded Adapter
6) HD-96925-58
XL (1986 to 1990)
7) HD-96940-52A
Banjo Bolt
8) HD-96921-104
Washer (2 req’d)
V-TWIN ENGINE/Gearcase cont.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
38
HD-96921-110
OIL PRESSURE GAUGE ADAPTER
Twin Cam 88
This tool is used with HD-96921-52B to accurately
check oil pressure.
HD-96921-120
OIL PRESSURE GAUGE ADAPTER
Twin Cam 88B
This tool is used with HD-96921-52B to accurately
check oil pressure.
HD-96925-58
OIL PRESSURE GAUGE ADAPTER
XL Models
(1986-1990)
This tool, when used with HD-96921-52B, will
allow the technician to connect the tool using
the threaded crankcase access hole.
HD-97080-77A
PINION SHAFT RACE INSTALLER
XL Models
(1977 - Early 1981)
Tool for installing inner race on pinion
gear shaft.
HD-33413-A
CARBURETOR IDLE ADJUSTMENT TOOL
All Models
Easily adjusts fast and slow idle setting without air
cleaner removal. HD-33413-1 replacement tip
& bit.
1) HD-33413-1A Replacement Tip
HD-35801
INTAKE MANIFOLD SCREW WRENCH
All Evolution Models
This extra long bolt wrench allows the technician
to remove and install the
1
⁄
4
" socket head cap
intake manifold screws quickly and easily without
having to remove vehicle components.
V-TWIN ENGINE/Gearcase cont.
V-TWIN ENGINE/Fuel System
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст