Harley Davidson Softail Delux FLSTN BIKE 2011-2015. Service Manual — page 31
7
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-33805
CLEVEBLOCK SPREADING TOOL
All Five Speed Rubber
Mount Big Twins
This tool facilitates installation of swing arms.
(1980-2001)
(Except Dyna Models)
1) J-23444-A Thread Lube
HD-34190
FORK BUSHING AND SEAL INSTALLER
FXRT
(1983 & 1987)
Installs bushing and seal without damaging
XR &
components.
(1983-1987)
FX
(1984-1987)
HD-34633
AIR SUSPENSION PUMP AND GAUGE
All Air Suspension
Equipped Models
Accurately fills air suspensions without pressure
loss when disconnecting. (Improved design)
1) HD-34633-3 Gauge
2) HD-34633-4 Hose & Fitting
3) HD-34633-5A Plunger
HD-34634
FORK BUSHING AND SEAL INSTALLER
FLT
Installs bushing and seal without damaging
FXWG
components.
(1984-Later)
HD-36583
FORK BUSHING AND SEAL INSTALLER
FXLR/FXRS
(1987 & Later)
Installs bushing and seal without damaging
components.
XL Models
(1988 & Later)
FXD Dyna Models
(1992 & Later)
HD-39301-A
STEERING HEAD BEARING RACE REMOVER
FXST
(1988 & Later)
Used to remove steering head bearing
outer races.
XL Models
(1982 & Later)
HD-39301-1 Removal Tool
HD-39301-2 Driver Handle Adapter
FXD Dyna Models, FLT
(1992 & Later)
V-TWIN CHASSIS/Forks & Frame
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
8
HD-39302
STEERING HEAD BEARING RACE INSTALLER
FXST
(1988 & Later)
Used to install steering head outer races.
XL Models
(1982 & Later)
FXD Dyna Models
(1992 &Later)
FLT (1993 & Later)
HD-39754
FXST FORK SPREADING TOOL
FXSTS
(1993 & Later)
This tool spreads the dog bones on the Springer
front end to allow installation of the front fender.
FXSTSB
(1995 & Later)
HD-39787-A
RIVET TOOL
All Models
HD-39787-A is great for rivets on all fiberglass
components, i.e. Tour Paks, etc. Old rivets
are drilled out and discarded. New rivets are
nice and snug when using HD-39787-A.
HD-39994-A
PAINT REPAIR KIT
All Models with
clear coat paint
This kit is used to repair surface imperfections
on painted steel or fiberglass parts. No need
to repaint or replace components when this kit
is used.
1) HD-39994-4 Hookit Pad
5) HD-39994-8
Wipes
2) HD-39994-5 Buff Pad
6) HD-39994-9
Finishing Material
3) HD-39994-6 Sanding Block
7) HD-39994-10
Final Finish
4) HD-39994-7 10 Micro Fine Discs 8) HD-39994-11A Medium Cut Material
HD-41177
FORK HOLDING TOOL
All Models
The HD-41177 is used to hold the fork legs
during normal service procedures when removed
from the chassis.
HD-45327
SWINGARM BEARING INSTALLER
FL Models
(2002 & Later)
Installs both left and right side swingarm bearings
squarely on their bores to the installed depth.
V-TWIN CHASSIS/
Forks & Frame cont.
9
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-45966
FRONT FORK COMPRESSOR
All Models with
cartridge style forks
Used for quick and easy compression of cartridge
style front forks for service repairs. Mounts in a
vise and includes an adapter for FL forks to eliminate
direct contact with spring coil. Also includes a
special rod to pull up the fork damper rod. Fits
models with lowering kits.
HD-45966-2 Collar
HD-46247-A
VEHICLE ALIGNMENT TOOL
All FL Models
(1993 & Later)
Vehicle alignment is very important to ensure
proper handling and vibration control. Use of
HD-46247 greatly reduces the time required
to perform the alignment procedure. New -A
version includes -7 & -8 for 2007 models.
HD-46247-1 Left Side (1993-2006)
HD-46247-2 Right Side (1993-2006)
HD-46247-7 Left Side (2007 & Later)
HD-46247-8 Right Side (2007 & Later)
HD-46281
SWINGARM BEARING
XL Models
REMOVER & INSTALLER
(2004 & Later)
Removes and installs spherical swingarm bearings.
HD-47190
SEAT MOUNTING SCREW TOOL
Softail
Tool encapsulates the seat mounting screw to
avoid slipping off the screw and damaging the
rear fender paint.
HD-47255
STEERING BEARING ENDPLAY WRENCH
FX Springer Models
Adjusts the preload on Springer steering
head bearings.
HD-47925
REAR AXLE WRENCH
FL Models
Allows a secure hold on the rear axle nut for
VRSC Models
loosening or removal of the rear axle without
removal of the exhaust system.
V-TWIN CHASSIS/
Forks & Frame cont.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
10
HD-59000-B
OIL LEVEL GAUGE
Cartridge Fork Models
This tool is used for accurate fork oil
level adjustment.
HD-93330
IGNITION FORK LOCK TOOL WITH PAINT
FLT Models
(1980-1992)
Correctly spaces fork lock and adjustment screw
and prevents mispositioning of screw while
tightening.
1) HD-93330-1 Touch-Up Paint
2) HD-93330-2 Ignition Fork Gauge
HD-96200-80
REAR SWING ARM ASSEMBLY TOOL
FLT Models
(1980-2001)
To remove and install rear swing arm pivot
components.
1) HD-96209-80 Draw Bolt
2) HD-96204-80 Inside Press Collar
3) HD-96210-80 Washer
4) Nut (
7
⁄
16
- 20)
5) HD-96202-80 Press Collar
6) HD-96208-80 Press Plug
HD-43293-A
BRAKE CALIPER PISTON REMOVER
All Models
(2000 & Later)
This tool will remove the pistons from four
piston brake calipers.
HD-97168-77
ALIGNMENT GAUGE
FL, FX
(1973-1979)
Used to align rear brake disc and brake pads.
0
0
0
0
0
1
2
3
4
5
60
mL
V-TWIN CHASSIS/
Forks & Frame cont.
V-TWIN CHASSIS/Brakes
11
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-34633
AIR SUSPENSION PUMP AND GAUGE
All Air Suspension
Models
Accurately fills air suspensions without pressure
loss when disconnecting.
1) HD-34633-3 Valve
2) HD-34633-4 Hose & Fitting
3) HD-34633-5A Plunger
HD-94700-52C
SHOCK ABSORBER SPANNER WRENCH
K, KH
Used to adjust shock absorbers for more or
FL
less spring compression.
XL Models
(1967-1974)
FXD Dyna Models
(1991 & Later)
XL Sport
(1996 & Later)
HD-94820-75A
REAR SHOCK SPANNER WRENCH
XL Models
(1975 & Later)
Adjusts spring compression.
FLT
FXR
HD-28431-C
(24) 1-OZ. FLUORESCENT ADDITIVES (OIL)
All Models
HD-28431-6A
(6) 1-OZ. FLUORESCENT ADDITIVES (OIL)
HD-28431-16
(1) 16 OZ. FLUORESCENT ADDITIVE (OIL)
Improved additive shows brighter under black light.
HD-34816
OIL FILTER SWITCH WRENCH
All 1340 cc
Evolution Models
This tool will easily install and remove oil
except FLT & FLHT
pressure switches without damage to the switch
itself. The extension handle is not used when
XL Models
servicing Sportsters.
(Late 1983-1985)
V-TWIN CHASSIS/
Shock Absorbers
V-TWIN ENGINE/General
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
12
HD-35457
BLACK LIGHT LEAK DETECTOR
All Models
The Black Light Oil Leak Detector provides
an effective time saving method for pinpointing
engine oil leaks. Simply add 1 oz. of fluorescent
oil additive to the engine crankcase (6 oz.
included). Run the engine for ten minutes to
circulate the fluorescent oil additive throughout
the engine. Oil leak will fluoresce a bright yellow
when illuminated with HD-35457 Black Light.
HD-39565
ELECTRONIC LISTENING TOOL, ENGINE EAR
®
All Models
The Engine EAR
®
helps to amplify sounds and
also shuts out surrounding noises. Very helpful in
identifying worn components and internal engine
noises. Comes with carrying case.
HD-39964
COOL TOOL
All Models
This cutting fluid works well with both
taps and reamers.
HD-41417
PROPANE ENRICHMENT KIT
All Models
Checks for suspected leaks in engine intake by
changing engine tone when propane enters source
of leak. Kit comes with all necessary components
except for propane bottle.
HD-41675
OIL PRESSURE SENDING UNIT WRENCH
XL Sport
(1996 & Later)
The oil pressure sending unit on all 1995 to
current vehicles can be difficult to remove because
of its location on the engine.
V-TWIN ENGINE/General cont.
13
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-42310
ENGINE/TRANSMISSION STAND
See Below
The Engine/Transmission Stand will make engine
repair easier than ever before. Engines and
transmissions can be rotated and tilted into various
work positions. Crankcases can even be split to
perform complete engine overhauls. Transmissions
can also be supported for easy maneuverability.
HD-42310-200 Wing Nut firmly locks cradle in stand
for crankcase main bearing lapping.
B-43987
Engine Cradle (Blast 2004 & Later) & (XB9R Firebolt 2003 & Later)
HD-42310
Benchtop Stand (Cradles Not Included)
HD-42310-1
Evolution/Shovelhead Cradle
HD-42310-2B
Twin Cam 88 Cradle (Slotted holes for easy attachment)
HD-42310-3
Sportster Engine Cradle (thru 2003)
HD-42310-20A
5-Speed Transmission Cradle
HD-42310-25A
Twin Cam 88B Cradle
HD-42310-40
V-Rod Cradle
HD-42310-45
Sportster Engine Cradle (2004 & Later)
HD-42310-50A
6-Speed Transmission Cradle
HD-42310-200
Cradle Lock Wing Nut
HD-42310-150
ENGINE STAND DRIP TRAY
All Models
This tool is used with the HD-42310 Engine Stand
to catch engine and transmission oil.
HD-42311
OIL FILTER WRENCH
All Models
Use to remove oil filters.
HD-42508
TORX PLUS BIT KIT
1997 Models
Torx Plus fasteners were used on 1997 model
year vehicles. The HD-42508 Torx Plus Bit Kit
includes T-40 I.P. & T-45 I.P. tools necessary to
service these fasteners.
1) HD-42508-1 Holder
2) HD-42508-2 T-40 Torx Bit
3) HD-42508-3 T-45 Torx Bit
V-TWIN ENGINE/General cont.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
14
HD-43646-A
ROLLING ENGINE STAND
All Models
This engine stand uses the cradles from the
Bench Top Engine stand and can be rolled around
the service department. The engines can be tilted
into various positions and is height adjustable.
HD-43464-A includes wide span leg for V-Rod engine.
HD-43646-50 Wide Span Leg For V-Rod Engine
(for previous stand HD-43646)
HD-43646-10 Oil Drip Tray
HD-44067-A
OIL FILTER WRENCH
All Models
Allows access around the crank position
sensor to remove the oil filter. New improved
version allows removal of filters attached to an
accessory oil cooler adapter.
HD-46284
ENGINE HOOK
XL Models
(2004 & Later)
Lifts XL engine from chassis during removal and
installation. Used with floor crane or chainfall.
HD-47183
LEAK DETECTOR PENLIGHT
All Models
Small penlight design permits leak
detection in very tight areas.
HD-47184
LEAK DETECTOR FLASHLIGHT
All Models
Convenient flashlight design permits leak
detection in tight places. Clips to battery
terminal for 12 volt power.
HD-47187
TECHNICIAN PENLIGHT
All Models
Provides bright white light source in poorly
lit areas.
V-TWIN ENGINE/General cont.
15
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-47188
TECHNICIAN FLEX LIGHT
All Models
Flexible neck provides bright white light
source in hard-to-reach areas.
HD-96950-68
VACUUM GAUGE
FL
(1965 & Earlier)
Measures front chain case vacuum to detect air
leaks (30 in. water, 1.05 P.S.I.).
FLT (1984
1
⁄
2
& Earlier)
1) HD-96955-68 Fitting
FX
2) HD-96952-68 Gauge
HD-33223-1
CYLINDER COMPRESSION GAUGE
All Models
This new compression gauge features a quick
disconnect coupler for easy handling. Used for
all models.
HD-33446-B
CYLINDER BORING TORQUE PLATES
All Big Twin Evolution
This tool properly stresses the cylinder to simulate
Sportster Evolution
engine operating conditions. It is required to
properly hone, bore, and measure the cylinder.
Shovelhead
Used in conjunction with HD-33446-86 (included)
for XL Evolution.
1) HD-33446-1 Top Plate
2) HD-33446-2 Bottom Plate
3) HD-33446-4 Evolution Bolts (4) & Washers (4)
4) HD-33446-5 Shovelhead Lower Bolts (4) & Washers (4)
5) HD-33446-6 Shovelhead Upper Bolts (5) & Washers (5)
HD-34624
CYLINDER HEAD STUD INSTALLER
Early 1340cc
Evolution Only
This tool installs the cylinder studs into the
engine case to the proper depth. (Early 1340cc
Evolution only)
1) HD-34624-1 Guide Spacer Tube
2) HD-34624-2 Screw Assembly
V-TWIN ENGINE/General cont.
V-TWIN ENGINE/Cylinder Head & Cylinder
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
16
HD-35667-A
CYLINDER LEAKDOWN TESTER
All Models
HD-35667-A will test for defective piston rings,
cylinder walls, valves, gaskets and all related
leakage problems. HD-35667-A uses existing shop
air and pinpoints the exact defect.
HD-39782-A
CYLINDER HEAD SUPPORT STAND
All Models
The cylinder head support stand kit includes
adapters to fit all Harley-Davidson cylinder heads.
These stands are especially nice for use when
removing or installing valve guides. They make
it easy to use an arbor press to push the guides
in and out on a straight line.
1) HD-39782-1 Stand
6) HD-39782-4
Adapter
2) HD-39782-2 Adapter
7) HD-39782-5
Adapter
3) HD-39782-6 Adapter
8) HD-39782-13 V-Rod Intake Adapter
4) HD-39782-7 Adapter
9) HD-39782-14 V-Rod Exhaust Adapter
5) HD-39782-3 Adapter
HD-39786
CYLINDER HEAD HOLDING FIXTURE
All Models
The cylinder head holding fixture is a
double ended tool. The ends are threaded
into the spark plug hole of the cylinder to
allow you to clamp the head into a vise.
This is especially handy when reaming and
honing valve guides.
HD-42324-A
CYLINDER TORQUE PLATES
Twin Cam 88
Permits accurate measurement of bore to
check for conditions of wear, taper, and out-of-round.
1) HD-42324-1A Lower Plate
2) HD-42324-2A Upper Plate
3) HD-42324-4 Bolt (4 Required)
HD-48116
HEAD TEMP SENSOR SOCKET
XL Models
(2007 & Later)
Used to remove head temperature sensor.
Buett Models
(1999 & Later)
CYLINDER LEAKDOWN TESTER
JHYUY
Guibikhf iugu iu ptr td6rd
Foihjolm oijfollkop Yuooifoihfm
knsdl hlno hslnslnnsdl hlno
bs npond bpdk kznh
odlbndpob npond bndb n
CYLINDER LEAKDOWN TESTER
Bdhgkjsbkdv ’ ksjjlkn lk
knsdl hlno hslnsln nlslns finbp pffb
odlbndpob nponno[bho
knsdl hlno hslnsln nlslns finbp pffb
odlbndpob npdb ndbno[bho
knsdl hlno hslnslnnsdl hlno hso[bho
knsdl hlno hslnslp pffb
odlbndpob npond bndb ndbno[bho
Bdhgkjsbkdv ’ ksjjlkn lk
knsdl hlno hslnsln nlslns finbp pffb
odlbndpob nponno[bho
knsdl hlno hslnsln nlslns finbp pklhb
odlbndpob npdb ndbno[bho
knsdl hlno hslnslnnsdl hlno hso[bho
bs npond bpdk kznh
odlbndpob npond bndb ndbno[bho
Bdhgkjsbkdv ’ ksjjlkn lk
knsdl hlno hslnsln nlslns finbp pffb
odlbndpob nponno[bho
knsdl hlno hslnsln nlslns finbp pklhb
Bdhgkjsbkdv Majjlkn Nolk
knsdl hlno hslnsln
ndpob npond
Bdhgkjsbkdv hlno hslnslp
knsdl hlno hslnsln
ndpob npond
V-TWIN ENGINE/
Cylinder Head & Cylinder cont.
17
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-48262
O2 SENSOR WRENCH
All Models w/
O2 Sensor
Used to remove O2 Sensor.
HD-94585-30
CYLINDER BASE NUT WRENCH
All Shovelhead Models
Fits
5
/
8
” nuts.
HD-94589-29B
CYLINDER BASE NUT AND HEAD
WL, G
BOLT WRENCH
KH, XL
Fits
9
/
16
” nuts.
All Shovelhead Models
HD-94590-73
SOCKET HANDLE, CYLINDER HEAD BOLT
U, K
BOLT WRENCH
KH, XL
3
/
8
” square drive for use with standard socket.
All Shovelhead Models
HD-34623-C
PISTON PIN RETAINING RING INSTALLER
All Evolution
This tool takes the frustration out of piston
Shovelhead
service by allowing a convenient means to
install retaining rings quickly and easily on all
XL Models
1983-Later Evolution pistons and Shovelhead
(Late 1985)
pistons 1983-later. Also works on late 1985
1000cc piston. New version adapts to redesigned
Buell XB9R Firebolt piston pin.
HD-35102
PISTON PIN BUSHING HONE (20mm)
All Models
This tool finish sizes wrist pin bushings after
reaming. Used for all models.
V-TWIN ENGINE/
Cylinder Head & Cylinder cont.
V-TWIN ENGINE/Piston & Connecting Rod
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
18
HD-42317-A
PISTON PIN RETAINING RING INSTALLER
Twin Cam 88/B
Used to install piston pin retaining clips.
HD-42318
CONNECTING ROD BUSHING REAMER
Twin Cam 88/B
Reamer sizes replacement connecting rod
bushings to size.
HD-42320-A
PISTON PIN EXTRACTOR
All Models -
(1965 & Later)
Removal of the piston pin can be time consuming.
With the HD-42320-A Pin Extractor, the job is easy.
Position the pin extractor next to a piston pin and
turn the handle. The piston pin will be removed
in seconds. New version removes redesigned
Buell Firebolt piston pins.
HD-42322
PISTON SUPPORT PLATE
All Models
Used to provide a stable platform for the piston
during piston ring installation and cylinder installation.
HD-42569
CONNECTING ROD BUSHING HONE
Twin Cam 88/B
Hone achieves final surface finish on bushing
after it has been reamed.
HD-43645
REAMER DRIVE SOCKET
Twin Cam 88/B
Used with HD-42318 Connecting Rod Bushing
Reamer & HD-42316 Crankshaft Bushing Reamer
to turn reamer shank.
1) HD-43645-1 Socket
2) HD-43645-4 Handle
V-TWIN ENGINE/Piston &
Connecting Rod cont.
19
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-94800-26A
CONNECTING ROD BUSHING REAMER SET
Used for reaming pistons and upper connecting
rod bushings.
1) HD-94800-1
.7922/.7920
Reamer 73-83 FL
Shovelhead
84-Later Evolution
1340
2) HD-94800-2
.7916/.7914
Reamer 57-85 XL
86 & Later
Evolution XL
3) HD-94800-3
.767
Pilot
73-83 Shovelheads
84-Later Evolution
1340
4) HD-94800-4
.773
Pilot
57-85 XL
86-Later Evolution
XL
HD-95952-33C
CONNECTING ROD CLAMPING TOOL
All Models
Holds connecting rod when fitting piston
pin bushing.
1) HD-95954-33 Base
2) HD-95952-1 (pkg of 2)
XL Models
(1996 & Later)
Twin Cam 88
(1999 & Later)
3) HD-95952-3 (pkg of 2)
1340 Evolution Models
(1984 & Later)
4) RS-9400-810 Thumb Screw (2 required)
HD-95970-32D
PISTON PIN BUSHING TOOL
All Models
Used to remove and replace piston pin bushings
without removing connecting rod from
crankcase.
1) HD-95970-101 Washer
2) HD-95984-32B Receiver Cup
3) HD-95986-32B Remover/Installer
4) J-28668-5
Bolt
5) J-23444-A
Thread Lube
6) J-22342-18
Nice Bearing
7) RS-3600-450
Nut (
3
⁄
8
-16)
8) HD-95986-99
Remover/Installer
9) HD-95984-99
Receiver Cup
V-TWIN ENGINE/Piston &
Connecting Rod cont.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
20
HD-96333-51E
PISTON RING COMPRESSING TOOL
All Models
To insert pistons with rings into cylinders.
Compresses rings to bore size.
1) HD-96333-100 Ring Compressor Pliers
2) HD-96333-101 Band 2
7
⁄
8
–3
1
⁄
8
3) HD-96333-102 Band 3
3
⁄
8
–3
5
⁄
8
4) HD-96333-103 Band 3
5
⁄
8
–3
7
⁄
8
5) HD-96333-105 Band 3
7
⁄
8
–4
1
⁄
8
6) HD-96333-106 Band 4
1
⁄
8
–4
3
⁄
8
VRSC Models 1250 cc Engine
HD-96740-36
CONNECTING ROD LAPPING ARBOR
FL
For lapping connecting rod bearing races when
XL
fitting new rollers.
K, KH
1) HD-96746-36 1
5
⁄
8
" Lap
1)
(FL, XL, K, KH, XR, FXU, FLT, FX)
U
2) HD-96741-17 Lapping Arbor
3) HD-96745-17 Adjusting Nut
FLT
4) HD-96743-17 Lock Nut
5) HD-96744-17 Adjusting Collar
B-45655
CRANKCASE BEARING REMOVER
Twin Cam 88/B
& INSTALLER
(2003 & Later)
Used with HD-42720 to remove and install
XB9/XB12 Firebolt
crankcase main bearings.
(2003 & Later)
XL Models
(2004 & Later)
HD-34813
ROWE FLYWHEEL REBUILDING JIG
All Models
This tool is used to remove and replace the
mainshaft, crank pin nut, and upper flywheel.
It is also used to tighten the crank pin nut.
HD-38871
CRANKSHAFT BUSHING PLATE
XL Models
PILOT AND REAMER
(1991 & Later)
Reams inboard Camshaft crankcase bushings.
1) HD-38871-4 Plate
2) HD-38871-2 Reamer
3) HD-38871-5 Screws
V-TWIN ENGINE/Piston &
Connecting Rod cont.
V-TWIN ENGINE/Flywheel & Crankcase
21
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
HD-39361-B
BIG TWIN SPROCKET SHAFT SEAL INSTALLER
FL/FX
(1969 & Later)
Installs sprocket shaft seal.
Use with HD-97225-55B.
New -B version works on all models including
2006 & later models.
HD-39458
SPROCKET SHAFT BEARING OUTER
Big Twins
RACE INSTALLER
(1969-2002)
Used with a shop press to simply and easily install
XL Models
the Timkin bearing races to the correct depth.
(1977-2003)
1) HD-39458-1 Base
2) HD-39458-2 Sportster Pilot
3) HD-39458-3 Big Twin Pilot
HD-39958
PINION BEARING RACE REMOVAL
Big Twins
& INSTALLATION TOOL
(1958 & Later)
This tool is used to remove and install
the pinion bearing outer race on 1958
to current models.
HD-41492-A
CRANKSHAFT LOCKING TOOL
All Big Twins
(Except Twin Cam 88)
The HD-41492-A locks the crankshaft by engaging
the pinion shaft splines. This permits the removal
and torquing of the pinion nut during installation.
HD-41506
CRANKSHAFT LOCKING TOOL
XL Models
(1991-1999)
The HD-41506 locks the crankshaft by
engaging the pinion shaft splines.
This permits the removal and torquing of
the pinion nut during installation.
HD-42122
FLYWHEEL PROTECTIVE COVER
Fuel Injected Engines
(1995-1998)
The HD-42122 is used to protect the flywheel
when removing the crankpin.
HD-42315
CRANKSHAFT BUSHING REMOVER
Twin Cam 88
& INSTALLER
Removes and installs crankshaft bushing
in support plate.
1) HD-42315-1 Remover/Installer
2) HD-42315-2 Base
V-TWIN ENGINE/
Flywheel & Crankcase cont.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
APPLICATION
22
HD-42316
CRANKSHAFT BUSHING REAMER
Twin Cam 88
Tool reams replacement crankshaft bushings.
1) HD-42316-1 Reamer
2) HD-42316-2 Pilot
HD-42326-A
CRANKSHAFT GUIDE
All Twin Cam 88/B
Spreads crankcase pinion bearing rollers
XB9/XB12 Firebolt
during crankcase reassembly.
(2003 & Later)
XL Models
(2004 & Later)
HD-42579
SPROCKET SHAFT BEARING INSTALLER
XL Models
(1977-2003)
This tool will install the Sprocket Shaft Bearing
to the proper depth.
1) HD-42579-4
Handle
2) HD-42579-2
Screw
3) HD-42579-3
Collar
4) J-23444-A
Thread Lube
5) 12702
Bearing
6) 12330
Washer
HD-42720-A
CRANKCASE BEARING REMOVER
Twin Cam 88
& INSTALLER
Removes and installs right crankcase main bearing.
1) HD-42720-1 Installer
2) HD-42720-2 Base
3) HD-42720-5 Base (2003 TC88/B)
HD-42774
SPROCKET SHAFT SEAL INSTALLER
XL Models
(1977-2001)
The HD-42774 will install the sprocket shaft seal.
Used with HD-42579 Sprocket Shaft Bearing Installer.
HD-43720
TIMKEN SNAP REMOVER & INSTALLER
Big Twin Models
(1969 & 2002)
Removes and installs the Timken outer race
snap ring in the left crankcase half.
V-TWIN ENGINE/
Flywheel & Crankcase cont.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст