Chrysler Voyager. Manual — part 19
Symptom:
P0141-1/2 O2 SENSOR HEATER FAILURE
When Monitored and Set Condition:
P0141-1/2 O2 SENSOR HEATER FAILURE
When Monitored:
During vehicle shutdown after the vehicle has been driven for greater
than 10 miles with the throttle open for a minimum of 3 minutes. Battery voltage greater
than 11.0 volts.
Set Condition:
O2 sensor continues to rise, (instead of fall) after the diagnostics has
turned the ASD relay back on. Two trip fault.
POSSIBLE CAUSES
O2 SENSOR HEATER OPERATION
O2 HEATER ELEMENT
O2 SENSOR HEATER GROUND CIRCUIT OPEN
ASD RELAY OUTPUT CIRCUIT OPEN
PCM
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, read DTC’s.
Is the Good Trip display and equal to zero?
All
Yes
→ Go To 3
No
→ Go To 2
2
Turn the ignition off.
NOTE: Wait a minimum of 8 minutes to allow the O2 Sensor to cool down
before continuing the test. Allow the O2 Sensor voltage to stabilize between
0.4 to 0.6 volts.
Turn the ignition on.
With the DRBIII
t, actuate the O2 Heater Test.
With the DRBIII
t, monitor O2 Sensor voltage for at least 2 minutes.
Does the voltage stay between 0.4 and 0.6 volts?
All
Yes
→ Go To 3
No
→ Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
75
DRIVEABILITY - SBEC
TEST
ACTION
APPLICABILITY
3
NOTE: Allow the O2 sensor to cool down to room temperature.
Turn the ignition off.
Disconnect the O2 Sensor harness connector.
Measure the resistance across the O2 Sensor Heater element component side.
NOTE: O2 Sensor Heater Resistance Specification: 1/1 and 2/1 O2 Sensor 3.0
to 4.0 ohms 2/1 and 2/2 4.0 to 5.0 ohms.
Is the resistance between 4.0 and 7.0 ohms?
All
Yes
→ Go To 4
No
→ Replace the O2 Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
4
Turn the ignition off.
Disconnect the O2 Sensor harness connector.
Measure the resistance of the O2 Sensor Heater ground circuit in the O2 Sensor
harness connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 5
No
→ Repair the O2 Sensor Heater ground circuit for an open.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
5
Turn the ignition off.
Disconnect the O2 Sensor harness connector.
With the DRBIII
t, actuate the O2 Heater Test.
Measure the voltage of the ASD Relay Output circuit in the O2 Sensor harness
connector.
Is the voltage above 11.0 volts?
All
Yes
→ Go To 6
No
→ Repair the open in the ASD Relay Output circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
6
NOTE: Before Continuing: Disconnect the PCM harness connector and
check the related wiring terminals for corrosion, damage or terminal push
out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.
All
Repair
Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
76
DRIVEABILITY - SBEC
P0141-1/2 O2 SENSOR HEATER FAILURE —
Continued
Symptom:
P0171-1/1 FUEL SYSTEM LEAN
When Monitored and Set Condition:
P0171-1/1 FUEL SYSTEM LEAN
When Monitored:
With the engine running in closed loop mode, the ambient/battery
temperature above 20 deg. F and altitude below 8000 ft.
Set Condition:
If the PCM multiplies short term compensation by long term adaptive and
a certain percentage is exceeded for two trips, a freeze frame is stored, the MIL illuminates
and a trouble code is stored.
POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
RESTRICTED FUEL SUPPLY LINE
FUEL PUMP INLET STRAINER PLUGGED
FUEL PUMP MODULE
O2 SENSOR
O2 SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
O2 SENSOR HEATER OPERATION
THROTTLE POSITION SENSOR VOLTAGE GREATER THAN 0.92 VOLTS WITH THROTTLE
CLOSED
TP SENSOR SWEEP
MAP SENSOR OPERATION
ECT SENSOR OPERATION
ENGINE MECHANICAL PROBLEM
FUEL FILTER/PRESSURE REGULATOR (HIGH)
PCM
TEST
ACTION
APPLICABILITY
1
NOTE: Check for contaminates that may have damaged the O2 Sensor:
contaminated fuel, unapproved silicone, oil and coolant.
Turn the ignition on.
With the DRBIII
t, read DTC’s.
Is the Good Trip displayed and equal to zero?
All
Yes
→ Go To 2
No
→ Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
77
DRIVEABILITY - SBEC
TEST
ACTION
APPLICABILITY
2
Warning: The fuel system is under a constant pressure (even with the engine
off). Before testing or servicing any fuel system hose, fitting or line, the fuel
system pressure must be released.
Install a fuel pressure gauge to the fuel rail.
Turn the ignition on.
With the DRBIII
t, actuate the ASD Fuel System test and observe the fuel pressure
gauge.
NOTE: Fuel pressure specification is 400 KPa +/- 34 KPa (58 psi +/- 5 psi).
Turn the ignition off.
Choose a conclusion that best matches your fuel pressure reading.
All
Within Specification
Above Specification
Replace the fuel filter/pressure regulator.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
Below Specification
Caution: Stop All Actuations.
3
Turn the ignition on
With the DRBIII
t, read the O2 Sensor voltage.
Is the voltage between 0.4 to 0.6 volts?
All
Yes
→ Go To 4
No
→ Go To 10
4
Turn the ignition off.
NOTE: Wait a minimum of 10 minutes to allow the O2 Sensor to cool down
before continuing the test. Allow the O2 Sensor voltage to stabilize between
0.4 to 0.6 volts.
Turn the ignition on.
With the DRBIII
t, actuate the O2 Heater Test.
With the DRBIII
t, monitor O2 Sensor voltage for at least 2 minutes.
Does the voltage stay between 0.4 and 0.6 volts.
All
Yes
→ Replace the O2 Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No
→ Go To 5
5
Turn the ignition on.
With the DRBIII
t, read TP Sensor voltage.
NOTE: The throttle must be against the stop.
Is the TP Sensor voltage 0.92 or less with the throttle closed?
All
Yes
→ Go To 6
No
→ Check for a binding throttle condition. If OK, replace the TP
Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
78
DRIVEABILITY - SBEC
P0171-1/1 FUEL SYSTEM LEAN —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст