Ford Focus RS (2011 year). Manual — part 5
• XX = -1.0 mm +1.0 mm to -2.0 mm.
TIE0037260
29. If further adjustment is required repeat the
door hinge to door adjustment.
30. NOTE: Make sure that the front and rear
doors are in the fully closed position.
If no further adjustment is required check
and note any misalignment of the front door
in relation to the rear door.
• XX = 0.0 mm +1.0 mm to -0.0 mm.
TIE0037261
31. Open the front door and mark the position
of the front door latch striker plate, to use
as reference points as necessary.
32. Loosen the striker plate retaining screws
one half turn.
TIE0037256
33.
CAUTION: Protect the B-pillar using a
soft cloth to prevent damage.
Using a suitable soft faced hammer, adjust
the striker plate as necessary.
TIE0037616
34. Tighten the striker plate retaining screws.
TIE0037264
20 Nm
35. Close the front door.
36. NOTE: Make sure that the front and rear
doors are in the fully closed position.
Check and note any misalignment of the
front door in relation to the rear door.
• XX = 0.0 mm +1.0 mm to -0.0 mm.
TIE0037261
G391258en
501-03-
19
Body Closures
501-03-
19
GENERAL PROCEDURES
37. If further adjustment is required repeat the
front door latch striker plate to B-pillar
adjustment.
38. If no further adjustment is required open
the front door.
39. Connect the electrical connector.
TIE41216
40. Attach the electrical connector to the
A-pillar.
TIE41215
41.
CAUTION: Make sure that the door
check strap is correctly aligned.
Attach the door check strap to the A-pillar.
1. Pull the check strap to the open position.
2. Install the retaining screw.
TIE0037263
1
23 Nm
2
G391258en
501-03-
20
Body Closures
501-03-
20
GENERAL PROCEDURES
Rear Door Alignment
1. NOTE: Make sure that the front and rear
doors are in the fully closed position.
Check and note any misalignment of the rear
door in relation to the door frame and the
rear edge of the front door.
1. 3.5 mm ± 1.0 mm.
2. 6.0 mm ± 2.0 mm.
3. 4.5 mm ± 1.5 mm.
TIE0037294
1
1
2
2
3
3
1
1
2. If adjustment is required open the front door
and mark the position of the rear door
hinges, to use as reference points as
necessary.
3. Open the rear door.
4. Detach the door check strap from the
B-pillar.
1. Remove the retaining screw.
2. Push the check strap to the fully closed
position.
TIE0037258
1
2
5. Close the rear door.
6. Loosen the door hinge to B-pillar retaining
screws one half turn.
TIE0037293
7. Adjust the door hinges as necessary.
TIE0037643
8. Tighten the door hinge to B-pillar retaining
screws.
E0037296
30 Nm
30 Nm
9. Close the front door.
10. NOTE: Make sure that the front and rear
doors are in the fully closed position.
G330082en
501-03-
21
Body Closures
501-03-
21
GENERAL PROCEDURES
Check and note any misalignment of the rear
door in relation to the door frame and the
rear edge of the front door.
1. 3.5 mm ± 1.0 mm.
2. 6.0 mm ± 2.0 mm.
3. 4.5 mm ± 1.5 mm.
TIE0037294
1
1
2
2
3
3
1
1
11. If further adjustment is required repeat the
door hinge to B-pillar adjustment.
12. NOTE: Make sure that the front and rear
doors are in the fully closed position.
If no further adjustment is required check
and note any misalignment of the rear door
in relation to the front door.
• XX = 0.0 mm + 0.0 mm to - 1.0 mm.
TIE0037261
13. Open the front door.
14. Loosen the rear door hinge to door
retaining screws one complete turn.
TIE0037249
15. Adjust the door hinges to door as
necessary.
TIE0037644
16. Tighten the door hinge to door retaining
screws.
TIE0037292
48 Nm
17. Close the front door.
18. NOTE: Make sure that the front and rear
doors are in the fully closed position.
Check and note any misalignment of the rear
door in relation to the front door.
G330082en
501-03-
22
Body Closures
501-03-
22
GENERAL PROCEDURES
• XX = 0.0 mm + 0.0 mm to - 1.0 mm.
TIE0037261
19. If further adjustment is required repeat the
door hinge to door adjustment.
20. If no further adjustment is required check
and note any misalignment of the rear door
in relation to the rear body panel.
• XX = 0.0 mm +1.0 mm to - 0.0 mm.
TIE0037295
21. Open the rear door and mark the position
of the rear door latch striker plate, to use
as reference points as necessary.
22. Loosen the striker plate retaining screws
one half turn.
TIE0037256
23.
CAUTION: Protect the C-pillar using a
soft cloth to prevent damage.
Using a suitable soft faced hammer, adjust
the striker plate as necessary.
TIE0037616
24. Tighten the striker plate retaining screws.
TIE0037264
20 Nm
25. Close the rear door.
26. Check and note any misalignment of the
rear door in relation to the rear body panel.
• XX = 0.0 mm +1.0 mm to - 0.0 mm.
TIE0037295
27. If further adjustment is required repeat the
rear door latch striker plate to C-pillar
adjustment.
G330082en
501-03-
23
Body Closures
501-03-
23
GENERAL PROCEDURES
28. If no further adjustment is required open
the rear door.
29.
CAUTION: Make sure that the door
check strap is correctly aligned.
Attach the door check strap to the B-pillar.
1. Pull the check strap to the open position.
2. Install the retaining screw.
TIE0037263
1
23 Nm
2
G330082en
501-03-
24
Body Closures
501-03-
24
GENERAL PROCEDURES
Luggage Compartment Lid Alignment
1. Open the luggage compartment lid.
2. Remove the luggage compartment lid striker
retaining bolt covers.
E59325
3. Loosen the luggage compartment lid striker
retaining bolts.
E59326
4. Remove the luggage compartment lid
weatherstrip.
TIE0024380
5. Remove the luggage compartment lid bump
stops.
TIE0023906
6. Support the luggage compartment lid and
remove the support strut on both sides.
TIE0023907
7. Loosen the luggage compartment lid hinge
to body retaining bolts 2 complete turns on
both sides (luggage compartment lid shown
removed for clarity).
E59187
8.
CAUTION: Protect the luggage
compartment lid and vehicle body using soft
cloth(s) to prevent damage.
G468127en
501-03-
25
Body Closures
501-03-
25
GENERAL PROCEDURES
Loosen the luggage compartment lid hinge
to luggage compartment lid retaining bolts
2 complete turns on both sides.
E59189
9. Using plastic material, fabricate 4 spacers.
E60431
10. NOTE: Make sure that the luggage
compartment lid is in the fully closed
position.
Insert the spacers between the outer edges
of the luggage compartment lid and the rear
quarter panels on both sides.
E0023914
11. Push down in the luggage compartment lid
hinge area until the luggage compartment
lid is 2 mm below flush with the rear quarter
panel on both sides.
12. Remove the spacers.
13. NOTE: Make sure that the luggage
compartment lid does not move on the
luggage compartment lid hinges.
Carefully open the luggage compartment lid
and tighten the luggage compartment lid
hinge to luggage compartment lid retaining
bolts on both sides.
E59190
23 Nm
14. Tighten the luggage compartment lid hinge
to body retaining bolts on both sides
(luggage compartment lid shown removed
for clarity).
E59188
23 Nm
G468127en
501-03-
26
Body Closures
501-03-
26
GENERAL PROCEDURES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст