Ford E-250 (2006 year). Manual — part 14

Replacing lost remote entry transmitters

If you would like to have your remote entry transmitter reprogrammed
because you lost one, or would like to buy additional remote entry
transmitters, you can either reprogram them yourself, or take all
remote entry transmitters to your authorized dealer for
reprogramming.

How to reprogram your remote entry transmitters

You must have all remote entry transmitters (maximum of four)
available before beginning this procedure. If all remote entry transmitters
are not present during programming procedure, the ones missing during
programming will no longer operate the vehicle.

To reprogram the remote entry
transmitters:

1. Place the key in the ignition and
turn from the (2) LOCK position to
(3) OFF.

2. Cycle eight times rapidly (within
10 seconds) between the (3) OFF
position and (4) ON. Note: The
eighth turn must end in the (4) ON
position.

3. The doors will lock, then unlock, to confirm that the programming
mode has been activated.

4. Within 20 seconds press any button on the remote entry transmitter.
Note: If more than 20 seconds have passed you will need to start the
procedure over again.

5. The doors will lock, then unlock, to confirm that this remote entry
transmitter has been programmed.

6. Repeat Steps 4 and 5 to program each additional remote entry
transmitter (up to four transmitters).

7. Turn the ignition to the (3) OFF position after you have finished
programming all of the remote entry transmitters.

8. The doors will lock, then unlock, to confirm that the programming
mode has been exited.

3

1

2

5

4

Locks and Security

57

Illuminated entry

The interior lamps illuminate when the remote entry system is used to
unlock the door(s) or sound the personal alarm.

The illuminated entry system will turn off the interior lights if:
• the ignition switch is turned to the 4 (ON) or 1 (ACCESSORY)

position, or

• the remote transmitter lock control is pressed, or
• after 25 seconds of illumination.
The dome lamp control (if equipped) must not be set to the off position
for the illuminated entry system to operate.

The inside lights will not turn off if:
• they have been turned on with the dimmer control, or
• any door is open.

Locks and Security

58

SEATING

Notes:

Reclining the seatback can cause an occupant to slide under the
seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

Do not pile cargo higher than the seatbacks to reduce the risk of
injury in a collision or sudden stop.

Before returning the seatback to its original position, make sure
that cargo or any objects are not trapped behind the seatback.

After returning the seatback to its original position, pull on the
seatback to ensure that it has fully latched. An unlatched seat may
become dangerous in the event of a sudden stop or collision.

Adjusting the front manual seat (if equipped)

Never adjust the driver’s seat or seatback when the vehicle is
moving.

Always drive and ride with your seatback upright and the lap
belt snug and low across the hips.

Lift handle to move seat forward or
backward.

Seating and Safety Restraints

59

Pull lever up to adjust seatback.

Before returning the
seatback to its original

position, make sure that cargo or
any objects are not trapped
behind the seatback. After
returning the seatback to its
original position, pull on the
seatback to ensure that it has fully
latched. An unlatched seat may
become dangerous in the event of
a sudden stop or collision.

Using the manual lumbar support

The lumbar support control is
located on the inboard side of the
driver’s seat.

Turn the lumbar support control
clockwise to increase firmness.

Turn the lumbar support control
counterclockwise to increase
softness.

Adjusting the front power seat (if equipped)

The control is located on the outboard side of the seat cushion.

Press to raise or lower the front
portion of the seat cushion.

Seating and Safety Restraints

60