SsangYong Stavic / SsangYong Rodius (2005 year). Service manual — part 226
9
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
RK STICS
STAVIC - 2004.09
2C
2. The wiper relay is turned on 0.3 seconds (T1) after turning “ON” the washer switch over 0.6 seconds (T2) with the
ignition key “ON”, and it is turned on three times immediately after turning off the washer switch.
6. FUNCTIONS OF RK STICS
1) Wiper Control
Wiper MIST and Washer Coupled Wiper
1. The wiper relay is turned on 0.3 seconds (T1) after turning “ON” the washer switch for 0.2 ~ 0.59 seconds (T2) with
the ignition key “ON”, and it is turned off when the parking terminal is turned off.
T1: within 0.5s
T2: over 0.6s
T3: one wipter cycle
10
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
RK STICS
STAVIC - 2004.09
2C
3. If the washer operating signal is inputted while the wipers are operating in intermittent or AUTO mode, the system
stores the previous intermittent interval and operates the washer coupled wiper. After then, the wiper operation
returns back to intermittent or AUTO mode with the stored operating interval.
T1: within 0.3s
T2: 0.2 ~ 0.59s
T3: over 0.6s
T4: 3 cycles
T5: operationg interval
11
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
RK STICS
STAVIC - 2004.09
2C
Rain Sensor Coupled Wiper
If equipped with RE-STICS rain sensor, has following operation system.
1. System layout
This vehicle has a different wiper control logic compared to other models. As shown in the system diagram, the rain
sensor unit does not control wiper directly. The rain sensor unit sends infrared rays signal through LED and then
receives it with photo diode and then sends the returned signal to STICS and the STICS controls the wipers directly.
For more details, refer to rain sensing wiper section in this manual.
Multi-function (wiper)
switch
Rain
sensor
Wiper motor
RESTICS
Wiper LO
Wiper HI
12
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
RK STICS
STAVIC - 2004.09
2C
2. Rain sensing operation point
1) The wiper relay is turned on and the wiper motor runs one cycle when the ignition key is turned to “ON” position
(while the wiper switch is in “AUTO” position).
2) The wiper relay (LO) is turned on and the wiper motor runs one cycle when changing the wiper switch to “AUTO”
position from any other positions (while the ignition key is in “ON” position). When the wiper switch is turned to
“AUTO” position again from other positions, the system drives the wiper relay (LO) to run the wiper motor one cycle
only when the rain sensor detects the “Rain Detected” signal.
3. Rain sensing sensitivity control
The wiper relay is turned on and the wiper motor runs one cycle when the volume sensitivity is increased (ex: from 0 to
1) (while the ignition key is in “ON” position, the wiper switch is in “AUTO” position, and the wiper motor is in “Parked”
position). However, the wiper motor can be operated only when the rain sensor detects the “Rain Detected” signal.
* If the volume sensitivity is changed more than 2 stages within 2 seconds, the wiper motor runs only one cycle.
T1: 1 cycle
T1: 1 cycle
SENSITIVITY
RAIN SENSOR
Rain Detected
OFF
ON
OFF
WIPER RELAY
LO
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст