SsangYong Rexton. Service manual — part 620
SSANGYONG Y200
6E-16 STEERING COLUMN
SPECIAL TOOLS AND EQUIPMENT
SPECIAL TOOLS TABLE
Steering Wheel
Remover
YAD6E340
SECTION 7A
HEATING AND VENTILATION SYSTEM
TABLE OF CONTENTS
Description and Operation . . . . . . . . ... 7A-2
General . . . . . . . . . . . . . . . ... 7A-2
Specifications . . . . . . . . . . . . . .. 7A-3
Air Delivery and Function . . . . . . . . . . 7A-4
Schematic and Routing Diagrams . . . . . . 7A-6
Diagnostic Information and Procedures . . . .. 7A-7
Insufficient Heating Or Defrosting . . . . . . 7A-7
Blower Electrical . . . . . . . . . . . . .. 7A-9
Improper Air Delivery Or No Mode Shift . . . .. 7A-10
Too Much Heat . . . . . . . . . . . . .. 7A-11
Heater Controls . . . . . . . . . . . . .. 7A-12
Blower Noise . . . . . . . . . . . . . . 7A-13
Component Locator . . . . . . . . . . ... 7A-14
Airflow Through Vents With Rear Heating Duct ... 7A-14
Repair Instructions . . . . . . . . . . . .. 7A-15
On-Vehicle Service . . . . . . . . . . . ... 7A-15
Air Duct Assembly . . . . . . . . . . . 7A-15
Rear Cooler Duct . . . . . . . . . . . ... 7A-16
Heater and Blower Module Assembly . . . . . 7A-17
Heater Suction and Discharge Hose . . . . ... 7A-18
SSANGYONG Y200
7A-2 HEATING AND VENTILATION SYSTEM
DESCRIPTION AND OPERATION
GENERAL
Heater is the system that circulate the suction air
through the heater core to deliver the heat of engine
coolant to the suction air and designed for heating
and defrosting in the passenger room.
Heater system is consist of heater hose, heater module,
blower motor and adjustment system.
The control switch assembly (adjustment system)
equipped with the instrument panel can control the
temperature, the amount and the direction of the outlet.
Also this system can use the suction air as separation
between ambient air and intake air on the vehicle.
YAD7A010
HEATING AND VENTILATION SYSTEM 7A-3
SSANGYONG Y200
Blower Motor
Heater Core
Blower Motor Resistance
Front A/C and Heater Unit
Rear Cooler
Max. Capacity
Fin Pitch
Size (L x H x W)
Heating Capacity
1st Mode
2nd Mode
3rd Mode
4th Mode
Type
Heating Capacity
Cooling Capacity
Expansion Valve
Input Power
Type
Cooling Capacity
Expansion Valve
Input Power
Engine Type
SPECIFICATIONS
Heater+Evaporator and Blower (2 pieces)
Min. 4600 kcal/h (5.5 m
3
/Min)
Min. 4700 kcal/h (7.5 m
3
/Min)
Block Type
Max. 250 W
Evaporator and Blower (only Cooler)
Min. 2700 kcal/h (5 m
3
/Min)
ANGLE Type
Max. 180 W
GSL
GSL
7.425 - 9.075 kcal/h
1.52 mm
194.6 x180 x 35 mm
8,250 (Min. 4,700) kcal/h
3.25
Ω
1.45
Ω
0.35
Ω
Ω
←
←
←
←
←
←
←
←
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст