Jaguar X-Type Sedan and Estate (Wagon). Service manual — part 252
Published: 11-May-2011
Engine Cooling - 2.0L NA V6 - AJV6/2.5L NA V6 - AJV6/3.0L NA V6 - AJ27 -
Thermostat
Removal and Installation
Removal
1. Drain the cooling system. For additional information, refer to
For additional information, refer to:
Cooling System Draining, Filling and
Bleeding
(303-03A Engine Cooling - 2.0L NA V6 - AJV6/2.5L NA V6 -
AJV6/3.0L NA V6 - AJ27, General Procedures).
.
2. Detach the oil cooler coolant hose from the thermostat housing and
position to one side.
3. NOTE: The thermostat remains captive in the thermostat housing.
Remove the thermostat.
Remove and discard the gasket.
Installation
1. NOTE: Install a new gasket.
To install, reverse the removal procedure.
1. Tighten to 10 Nm.
2. Fill the cooling system. For additional information, refer to
For additional information, refer to:
Cooling System Draining, Filling and
Bleeding
(303-03A Engine Cooling - 2.0L NA V6 - AJV6/2.5L NA V6 -
AJV6/3.0L NA V6 - AJ27, General Procedures).
.
3. NOTE: For NAS vehicles only.
If required, carry out a long drive cycle.
For additional information, refer to:
Powertrain Control Module (PCM)
Long Drive Cycle Self-Test
(303-14A Electronic Engine Controls - 2.0L NA
V6 - AJV6/2.5L NA V6 - AJV6/3.0L NA V6 - AJ27, General Procedures).
Published: 11-May-2011
Engine Cooling - 2.0L NA V6 - AJV6/2.5L NA V6 - AJV6/3.0L NA V6 - AJ27 - Water
Pump
Removal and Installation
Removal
1. Drain the cooling system. For additional information, refer to
Cooling
System Draining, Filling and Bleeding
.
2. Lower the vehicle.
3. Remove the water pump belt. For additional information, refer to
Section
303-05 Accessory Drive
.
4. Remove the water pump drive pulley.
5. Remove the water pump.
Remove and discard the gasket.
Installation
1. NOTE: Install a new gasket.
To install, reverse the removal procedure.
Tighten to 10 Nm.
2. Tighten to 11 Nm.
Published: 11-May-2011
Engine Cooling - 2.0L NA V6 - AJV6/2.5L NA V6 - AJV6/3.0L NA V6 - AJ27 - Water
Pump Housing
Removal and Installation
Removal
1. Drain the cooling system. For additional information, refer to
Cooling
System Draining, Filling and Bleeding
.
2. Lower the vehicle.
3. Remove the water pump belt tensioner. For additional information, refer
to Section
303-05 Accessory Drive
.
4. Remove the left-hand valve cover. For additional information, refer to
Section
303-01A Engine
Section
303-01B Engine
.
5. Remove the water pump drive pulley.
6. Detach the coolant expansion tank outlet hose from the water pump
housing.
7. Remove the water pump coolant outlet pipe.
Remove and discard the seals.
8. Detach the coolant inlet pipe from the water pump housing.
Remove and discard the gasket.
9. Remove the water pump housing.
Remove and discard the gasket.
10. Remove the water pump from the water pump housing.
Remove and discard the gasket from the water pump.
Installation
1. NOTE: Install a new gasket.
To install, reverse the removal procedure.
Tighten to 10 Nm.
2.
CAUTION: Make sure that the water pump housing is tightened in
the sequence shown. Failure to follow this instruction may result in
damage to the water pump drive pulley bearings.
• NOTE: Install a new gasket.
Tighten in the sequence shown to 10 Nm.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст