Jaguar X-Type Sedan and Estate (Wagon). Service manual — part 586
1
1
1
1
1
1
1
1
1
1
1
1
I5:
Is there any 3rd party audio?
Yes
End.
No
Disconnect the Bluetooth link between the handset and vehicle phone system and re-try the call.
GO to I6
.
I6:
Does the 3rd party call audio work with the mobile phone disconnected from the vehicle?
Yes
Re-connect the Bluetooth link between the handset and the vehicle phone system and re-try the call.
GO to I8
.
No
Switch off the handset, remove the battery from the back of the handset. Replace the battery into the handset and
switch on. Make sure the Bluetooth link is disconnected and re-try the call.
GO to I7
.
I7:
Does the 3rd party call audio work with the mobile phone disconnected from the vehicle?
Yes
Problem may be due to a faulty Bluetooth connection.
No
This may be a handset issue, consult the handset supplier.
I8:
Does the 3rd party call audio work with the Bluetooth system?
Yes
Problem may be due to a faulty Bluetooth connection.
No
GO to I9
.
I9:
Does the 3rd party call audio work with the mobile phone in 'handset' mode?
Yes
GO to I10
.
No
Key off ignition and wait 6 minutes for the portable support electronics (PSE) module to shut down. Key on ignition.
Make sure the Bluetooth link is re-connected and re-try the call pairing and connecting.
GO to I14
.
I10:
Does the vehicle have voice control fitted?
Yes
GO to I11
.
No
GO to I12
.
I11:
Does the voice control pick up commands from the user?
Yes
Check harness connections between the microphone and the portable support electronics (PSE) module are not loose
or damaged.
GO to I16
.
No
Refer to the warranty policy and procedures manual if the voice control module is suspect.
I12:
Is the vehicle a USA/Canada/Mexico vehicle?
Yes
GO to I13
.
No
Check harness connections between the microphone and the portable support electronics (PSE) module are not loose
or damaged.
GO to I16
.
I13:
Does the vehicle have the voice control shorting loop fitted?
Yes
Check harness connections between the microphone and the portable support electronics (PSE) module are not loose
or damaged.
GO to I16
.
No
Fit the voice control shorting loop and check for normal operation.
I14:
Does the 3rd party call audio work with the Bluetooth system?
Yes
Problem may be due to a faulty Bluetooth connection.
No
Pair and connect a different known 'good' handset to the vehicle phone system and make an incoming call.
GO to I15
.
I15:
Does the 3rd party call audio work with the Bluetooth system?
Yes
This may be a handset issue, consult the handset supplier.
No
Check harness connections between the microphone and the portable support electronics (PSE) module are not loose
or damaged.
GO to I16
.
I16:
1
1
1
1
1
1
1
1
1
1
Are the microphone harness connections damaged?
Yes
Rectify as necessary. Refer to the electrical guides.
No
Replace the microphone and re-try the call.
GO to I17
.
I17:
Does the 3rd party call audio work with the Bluetooth system?
Yes
Problem may have been due to a faulty microphone.
No
Refer to the warranty policy and procedures manual if a module is suspect.
PINPOINT TEST J : NO IN-VEHICLE AUDIO
TEST
CONDITIONS
DETAILS/RESULTS/ACTIONS
J1:
Can the audio sources be heard through the vehicle speakers e.g. radio?
Yes
GO to J2
.
No
Check D2B connections are not loose or damaged. Reconnect/change/repair the D2B leads and check for normal
operation.
J2:
Can the call be heard when transferred to the handset?
Yes
Key off ignition and wait 6 minutes for the portable support electronics (PSE) module to shut down. Key on ignition.
Make sure the Bluetooth link is reconnected and re-try the call.
GO to J3
.
No
Disconnect the Bluetooth link between the handset and vehicle phone system and re-try the call.
GO to J4
.
J3:
Can the audio be heard through the vehicle speakers?
Yes
The audio problem may have been due to the Bluetooth link being disconnected.
No
Pair and connect a different known 'good' handset to the vehicle phone system and make a call to the 3rd party.
GO to
J7
.
J4:
Does the handset audio work with mobile phone disconnected from the vehicle?
Yes
Key off ignition and wait 6 minutes for the portable support electronics (PSE) module to shut down. Key on ignition.
Switch off the handset; remove the battery from the back of the handset. Replace the battery into the handset and
switch on. Key on ignition. Make sure the Bluetooth link is reconnected and re-try the call.
GO to J6
.
No
Try calling another 3rd party from the handset.
GO to J5
.
J5:
Is there any call audio on the handset?
Yes
Initial audio problem may be due to a fault at the 3rd party end, check by calling them on another number.
No
This may be a handset issue, consult the handset supplier.
J6:
Can the audio be heard through the vehicle speakers?
Yes
The audio problem may have been due to the Bluetooth link being disconnected.
No
Pair and connect a different known 'good' handset to the vehicle phone system and make a call to the 3rd party.
GO to
J7
.
J7:
Can the audio be heard through the vehicle speakers?
Yes
This may be a handset issue, consult the handset supplier.
No
Check harness connections between the Bluetooth upgrade module and the portable support electronics (PSE) module.
GO to J8
.
J8:
Are any of the harness connections damaged?
Yes
Rectify as necessary. Refer to the electrical guides.
No
Refer to the warranty policy and procedures manual if a module is suspect.
PINPOINT TEST K : NO RINGING HEARD THROUGH THE VEHICLE SPEAKERS
TEST
CONDITIONS
DETAILS/RESULTS/ACTIONS
K1:
1
1
1
1
1
1
1
1
1
1
1
When there is no call in progress, and the audio source is changed, is any audio heard e.g. from radio?
Yes
GO to K3
.
No
Check D2B connections are not loose and that all nodes are connected on the D2B ring. Rectify as necessary.
GO to
K2
.
K2:
Are any of the D2B connections damaged?
Yes
Change/repair the D2B leads and check for normal operation.
No
Call Technical Helpline.
K3:
Is the vehicle phone system volume set to more than 15?
Yes
GO to K4
.
No
Make sure that the vehicle phone system is set to more than 15 and retry the call.
K4:
Is the message "incoming call" displayed?
Yes
GO to K5
.
No
GO to K6
.
K5:
On answering the incoming call using the vehicle controls, can the 3rd party be heard through the vehicle speakers?
Yes
GO to K6
.
No
Go to 'No in-vehicle audio' - GO to Pinpoint Test
J.
K6:
Is there any ringing heard on the handset with the Bluetooth link connected?
Yes
GO to K7
.
No
GO to K10
.
K7:
Does the handset support in-band ringing or send its ringing status to the Bluetooth upgrade module?
Yes
Key off ignition and wait 6 minutes for the portable support electronics (PSE) module to shut down. Key on ignition.
Make sure the Bluetooth link is re-connected and re-try the call.
GO to K8
.
No
This is a handset issue, contact the handset supplier or replace with another handset from the approved list.
K8:
Can any ringing be heard through the vehicle speakers?
Yes
The audio problem may have been due to the Bluetooth link being disconnected.
No
Un-pair the current handset and pair/connect a known good handset with the vehicle. Make an incoming call.
GO to
K9
.
K9:
Can any ringing be heard through the vehicle speakers?
Yes
Contact the handset supplier, the handset may be faulty.
No
GO to K10
.
K10:
Is the message "incoming call" displayed?
Yes
Check the handset instructions to find "profile" settings.
GO to K14
.
No
GO to K11
.
K11:
Does the handset have good signal strength?
Yes
Disconnect the Bluetooth connection. Make sure the handset is not set to silent. Then make an incoming call.
GO to
K12
.
No
Move into area where the handset receives good signal strength. Make an incoming call and check for normal
operation.
K12:
Is there any ringing heard on the handset with the Bluetooth link disconnected?
Yes
Reconnect the Bluetooth connection, and then make an incoming call.
GO to K13
.
No
Contact the handset supplier, the handset may be faulty.
K13:
1
1
1
1
1
1
1
1
1
1
1
1
Can any ringing be heard through the vehicle speakers?
Yes
Problem due to a faulty Bluetooth link.
No
GO to K4
.
K14:
Has the handset "profile" been set to "silent"?
Yes
Change settings within profile, make an incoming call and check for normal operation.
No
GO to K15
.
K15:
Has the handset volume been set to minimum?
Yes
Increase volume setting, make an incoming call and check for normal operation.
No
Check Bluetooth connection between the handset and vehicle is OK.
GO to K16
.
K16:
Is the Bluetooth connection OK?
Yes
Disconnect the Bluetooth connection. Make sure that the handset is NOT set to silent, then make an incoming
call.
GO to K17
.
No
Follow the handset instructions for 'connecting' the Bluetooth link, then make an incoming call and check for normal
operation.
K17:
Is there any ringing heard on the handset?
Yes
Reconnect Bluetooth link between the handset and vehicle.
GO to K18
.
No
Un-pair the current handset and pair/connect a known good handset with the vehicle. Make an incoming call.
GO to
K9
.
K18:
Can any ringing be heard through the vehicle speakers?
Yes
Change settings within profile, make an incoming call and check for normal operation.
No
Check harness connections between the Bluetooth upgrade module and the portable support electronics (PSE)
module.
GO to K19
.
K19:
Are any of the harness connections damaged?
Yes
Rectify as necessary. Refer to the electrical guides.
No
Refer to the warranty policy and procedures manual if a module is suspect.
PINPOINT TEST L : LOW AUDIO VOLUME
TEST
CONDITIONS
DETAILS/RESULTS/ACTIONS
L1:
Low volume in vehicle (rather than at 3rd party)?
Yes
GO to L2
.
No
If volume is low at 3rd party.
GO to L9
.
L2:
Is the vehicle phone volume set at 12 or above?
Yes
Check fade & balance are both set at '0' or mid point on slider controls.
GO to L3
.
No
Increase phone volume to above 12.
GO to L1
.
L3:
Is radio volume OK?
Yes
GO to L4
.
No
Call Technical Helpline.
L4:
Is Bluetooth link between the handset and vehicle still connected?
Yes
GO to L5
.
No
Re-connect the Bluetooth link and re-try the call.
GO to L1
.
L5:
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст