Chery Tiggo 5 (T21). Service manual — part 186
16–
7
16
ON-VEHICLE SERVICE
Battery
Inspection
1. Check that battery terminals are not loose or corroded.
If battery terminals are corroded, clean them.
2. Check the battery for damage, deformation or leakage. If serious damage, deformation or leakage is
found, replace the battery.
3. Check the battery voltage.
Turn ignition switch to ON, and turn it off 20 to 30 seconds after turning on the headlights. This will
eliminate the surface charge on the battery. Measure battery voltage with digital multimeter.
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Remove the battery.
a. Loosen the negative battery cable locking nut, and
remove the negative (-) battery cable (1).
b. Open the battery positive terminal cover, loosen the
positive battery cable locking nut, and remove the
positive (+) battery cable (2).
c. Remove the battery pressure plate fixing nut (1).
(Tightening torque: 7 ± 1 N·m)
d. Remove the coupling bolt (2) between battery
pressure plate and tank upper crossmember.
(Tightening torque: 7 ± 1 N·m)
Testing Temperature
Specification
20°C
12 - 13 V
CAUTION
Be sure to wear necessary safety equipment to prevent accidents when repairing.
Try to prevent body paint surface from being scratched during removal and installation.
2
1
RT21160020
2
1
RT21160030
16–
8
16
e. Remove the battery.
Installation
Installation is in the reverse order of removal.
CAUTION
Please be careful to prevent metal tools from contacting both electrodes of battery at the same time or
accidentally touching the positive electrode and vehicle body.
CAUTION
Replace battery with a new one which conforms to the specifications.
Used battery contains sulfuric acid and lead, so never discard it at will. Please dispose of it at a qualified
local waste treatment station.
16–
9
16
Battery Tray and Tray Bracket
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Remove the battery (
).
3. Remove the battery tray.
a. Remove 2 coupling bolts (1) between battery tray and
air filter bracket.
(Tightening torque: 7 ± 1 N·m)
b. Remove 6 fixing bolts (2) from the battery tray.
(Tightening torque: 20 ± 2 N·m)
c. Remove the battery tray.
4. Remove the battery tray bracket.
a. Remove 4 fixing bolts (arrow) from the battery tray
bracket.
(Tightening torque: 20 ± 2 N·m)
b. Remove 2 battery tray brackets.
Installation
Installation is in the reverse order of removal.
CAUTION
Be sure to wear necessary safety equipment to prevent accidents when repairing.
Try to prevent body paint surface from being scratched during removal and installation.
1
2
RT21160040
RT21160050
16–
10
16
Alternator
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the engine trim cover assembly (
).
4. Remove the engine lower right protector assembly (
).
5. Loosen the accessory drive belt.
a. Put 15# open wrench (or socket) between engine and
right side-member, and tighten the tensioner pulley
bolt.
b. Rotate open wrench counterclockwise firmly indicated
by the arrow shown in the illustration. Loosen the
accessory drive belt (1) after it is slack.
6. Remove the alternator.
a. Move away the terminal cap, remove the fixing nut (1)
from alternator output cable, and move away the
alternator output cable.
(Tightening torque: 18 - 22 N·m)
b. Disconnect the alternator connector (2).
c. Remove 2 fixing bolts (arrow) from the alternator.
(Tightening torque: 20 + 5 N·m)
d. Remove the alternator from alternator bracket.
CAUTION
Be sure to wear necessary safety equipment to prevent accidents when repairing.
Try to prevent body paint surface from being scratched during removal and installation.
1
RT21160060
1
2
RT21160070
RT21160080
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст