Peugeot Partner (2022 year). Manual in english — page 5

Lighting and visibility

on the part of the driver. They can also come

In fog or snow, the rain/sunshine sensor

on if rain is detected, at the same time as the

may detect sufficient light. For this

automatic rain sensitive wipers.

reason, the lighting will not come on

As soon as the brightness returns to a sufficient

automatically.

level or after the windscreen wipers are switched

off, the lamps are switched off automatically.

The inner surface of the windscreen may

become misted up and affect the proper

operation of the rain/sunshine sensor.

In humid and cold weather, demist the

windscreen regularly.

The front lamps light up automatically when the

engine starts.

They provide the following functions:

► Turn the ring to the "AUTO" position. When

Daytime running lamps /

- Daytime running lamps (lighting control stalk in

the function is activated, a message is also

Sidelamps

the "AUTO" position with adequate light level).

displayed.

- Sidelamps (lighting control stalk in the "AUTO"

► Turn the ring to another position. An

position with low light levels or "Sidelamps only”

onscreen message is displayed to confirm that

or "Dipped/main beam headlamps").

the function has been deactivated.

The LEDs are brighter when operating as

Malfunction

daytime running lamps.

In the event of a malfunction of the rain/

sunshine sensor, the vehicle’s lamps

Guide-me-home and

come on and this warning lamp is displayed on

the instrument panel, accompanied by an

welcome lighting

audible signal and/or the display of a message.

Have it checked by a PEUGEOT dealer or a

Guide-me-home lighting

qualified workshop.

Automatic

Do not cover the rain/sunshine sensor,

With the ring of the lighting control stalk in the

located on the dashboard or at the top

"AUTO" position and when the light is poor, the

centre of the windscreen behind the interior

dipped beam headlamps come on automatically

rear view mirror (depending on equipment);

when the ignition is switched off.

the associated functions would no longer be

controlled.

Lighting and visibility

You can activate/deactivate this

Do not allow snow to accumulate on the

Automatic lighting

function and adjust the guide-me-

bonnet or roof of the vehicle as this could

home lighting duration in the Driving/Vehicle

systems - General

obstruct the camera.

touch screen menu.

recommendations

Manual

The automatic lighting systems use a detection

Automatic headlamp

camera, located at the top of the windscreen.

dipping

Operating limits

The system may be disrupted or not work

For more information, refer to the

correctly:

General recommendations for

- When visibility conditions are poor

automatic lighting systems.

(e.g. snowfall, heavy rain).

- If the windscreen is dirty, misted-up or

With the ring of the lighting control stalk in the

masked (e.g. sticker) in front of the camera.

"AUTO" position and the function activated on

- If the vehicle is facing highly reflective signs

the touch screen, this system automatically

► With the ignition off, pull the lighting control

or safety barrier reflectors.

switches between dipped and main beam

stalk toward you ("headlamp flash") to activate/

The system is not able to detect:

headlamps, according to lighting and traffic

deactivate the function.

- Road users that do not have their own

conditions, using a camera located at the top of

Manual guide-me-home lighting goes off

lighting, such as pedestrians.

the windscreen.

automatically after a period of time.

- Vehicles with hidden lighting (e.g. travelling

behind a safety barrier on the motorway).

Welcome lighting

- Vehicles at the top or bottom of a steep

With the "Automatic headlamp illumination"

slope, on winding roads, on crossroads.

function activated, in poor light, the sidelamps

and dipped beam headlamps come on

Maintenance

automatically when the vehicle is unlocked.

Clean the windscreen regularly,

Activation, deactivation and the

particularly the area in front of the camera.

duration of the exterior welcome

The internal surface of the windscreen can

lighting are set in the Driving/Vehicle touch

also become misted around the camera.

screen menu.

In humid and cold weather, demist the

windscreen regularly.

Lighting and visibility

This system is a driving aid.

- The dipped beam headlamps

- If the windscreen in front of the camera is

The driver remains responsible for

remain lit. These indicator lamps

dirty, misted or obscured (for example, by a

the vehicle's lighting, its correct use in the

light up on the instrument panel.

sticker).

prevailing light, visibility and traffic conditions,

The function is deactivated if the foglamps

- If the vehicle is facing highly reflective

and for compliance with driving and vehicle

are switched on or if the system detects poor

signs.

regulations.

visibility conditions (e.g. fog, heavy rain,

When the system detects thick fog, it

snowfall).

temporarily deactivates the function.

The system becomes operational when

When the foglamps are switched off or when the

The system is not able to detect:

the vehicle exceeds 16 mph (25 km/h).

visibility conditions become favourable again, the

- Road users that do not have their own

When the speed falls below 9 mph (15 km/h),

function is automatically reactivated.

lighting, such as pedestrians.

the function is no longer operational.

This indicator lamp goes out when the

- Vehicles whose lighting is obscured (for

function is deactivated.

example, vehicles driving behind a safety

barrier on a motorway).

Activation/Deactivation

Pause

- Vehicles at the top or bottom of a steep

The settings are changed via the

If the situation requires a change of headlamp

slope, on winding roads, on crossroads.

Driving/Vehicle touch screen

beam, the driver can take over at any time.

menu.

► A "headlamp flash" pauses the

Clean the windscreen regularly,

When deactivated, the lighting system changes

function and the lighting system switches

particularly the area in front of the

to "automatic illumination of headlamps" mode.

to "automatic illumination of lamps" mode:

camera.

The state of the system is stored when the

- If the "AUTO" and "Dipped beam" indicator

The internal surface of the windscreen can

ignition is switched off.

lamps were on, the system changes to main

also become misted around the camera.

beam.

In humid and cold weather, demist the

Operation

- If the "AUTO" and "Main beam"

windscreen regularly.

If the ambient light level is very low and traffic

indicator lamps were on, the system changes to

Do not allow snow to accumulate on the

conditions permit:

dipped beam.

bonnet or roof of the vehicle as this could

- The main beam headlamps

► To reactivate the function, once again switch

obstruct the detection camera.

come on automatically. These

the headlamps manually between dipped and

indicator lamps light up on the instrument panel.

main beam.

If the ambient light level is sufficient and/or the

The system may be disrupted or not work

traffic conditions do not allow the main beam

correctly:

headlamps to be lit:

- When visibility conditions are poor

(snowfall, heavy rain, etc.).

Lighting and visibility

stuck to the windscreen before operating the

Fast wiping (heavy rain)

Headlamp beam height

wipers.

adjustment

Normal wiping (moderate rain)

After using an automatic car wash, you

may temporarily notice abnormal noises

Intermittent wiping (proportional to the

and poorer wiping performance. You do not

vehicle’s speed)

need to replace the wiper blades.

Switching off

Single wipe (press down and release).

Without AUTO wiping

To avoid inconvenience to other road users,

Automatic wiping

the height of the halogen headlamps should be

adjusted according to the load in the vehicle.

Refer to the corresponding section.

(Initial setting)

Unladen.

Windscreen wash

Partial load.

► Pull the wiper control stalk towards you and

Medium load.

hold.

Maximum authorised load.

A final wiping cycle is performed when

4 5 6

Not used.

screenwashing ends.

With AUTO wiping

The windscreen wash jets are

incorporated into the tip of each wiper

Wiper control stalk

arm.

Screenwash fluid is sprayed along the length

Before operating the wipers in wintry

of the wiper blade. This improves visibility and

conditions, clear any snow, ice or frost

reduces screenwash fluid consumption.

from the windscreen and around the wiper

arms and blades.

With automatic air conditioning, any

Windscreen wipers

action on the screenwash control results

Do not operate the wipers on a dry

► To select the wiping speed: raise or lower the

in temporary closure of the air intake to

windscreen. In extremely hot or cold

stalk to the desired position.

protect the passenger compartment from any

weather, check that the wiper blades are not

odour.

Lighting and visibility

To avoid damaging the wiper blades, do

Screenwash-wipe

- clean them regularly using soapy water.

not operate the screenwash if the

- avoid using them to hold cardboard on the

screenwash reservoir is empty.

windscreen.

Only operate the screenwash if there is no

Reverse gear

- replace them at the first signs of wear.

risk of the fluid freezing on the windscreen

When reverse gear is engaged, the rear wiper

and hindering visibility. During the winter

will come into operation automatically if the front

Before removing a windscreen wiper blade

period, use "very cold climate" rated products.

windscreen wipers are operating.

Never top up with water.

Activation/Deactivation

The settings are changed via the

Low screenwash fluid level

Driving/Vehicle touch screen

When the low level of the reservoir is

menu.

reached, this warning lamp lights up on

the instrument panel, accompanied by an

This function is activated by default.

audible signal and a message.

Operating the wiper control stalk immediately

It comes on when the ignition is switched on,

after switching off the ignition will place the wiper

or every time the stalk is operated, until the

In the event of accumulation of snow or

blades in a vertical position.

reservoir is refilled.

hard frost or if a bicycle carrier is fitted to

► Proceed with the desired operation or the

Refill the screenwash reservoir (or have it

a towing device, deactivate the automatic rear

replacement of the wiper blades.

refilled) the next time you stop.

wiper via the touch screen’s Driving/Vehicle

After refitting a windscreen wiper blade

menu.

Rear wiper

► To return the wiper blades to their initial

position after the operation, switch on the ignition

Special position of the

and operate the wiper control stalk.

windscreen wipers

This maintenance position is used while cleaning

or replacing the wiper blades. It can also be

useful, in wintry weather (ice, snow), to release

► Turn the ring to align the desired symbol with

the wiper blades from the windscreen.

the marking.

Off

To maintain the effectiveness of the flat

wiper blades, it is advisable to:

Intermittent wiping

- handle them with care.

Lighting and visibility

Changing a wiper blade

► Unclip the worn wiper blade closest to you

Do not cover the rain/sunshine sensor.

and remove it.

When using an automatic car wash,

Removing/Refitting at the front

► Install the new wiper blade and clip it to the

switch off the automatic wipers and the

arm.

ignition.

► Repeat the procedure for the other wiper

In winter, wait until the windscreen is

blade.

completely clear of ice before activating the

► Starting with the wiper blade closest to you,

automatic wipers.

once again hold each arm by the rigid section,

then guide it carefully onto the windscreen.

Switching on

Removing/refitting at the rear

► Hold the arm by the rigid section and raise it

as far as possible.

► Clean the rear screen using screenwash

fluid.

► Carry out these wiper blade replacement

► Unclip the worn wiper blade and remove it.

► Give a short downwards push to the control

operations from the driver's side.

► Install the new wiper blade and clip it to the

stalk.

► Starting with the wiper blade farthest from

arm.

A wiping cycle confirms that the instruction has

you, hold each arm by the rigid section and raise

► Once again hold the arm by the rigid section,

been accepted.

it as far as possible.

then guide it carefully onto the rear screen.

This indicator lamp lights up on the

Take care not to hold the arms at the jet

instrument panel, accompanied by

Automatic windscreen

locations.

a message.

Do not touch the wiper blades - risk of

wipers

Depending on version, this indicator lamp

irreparable deformation.

appears on the display or on the instrument

In AUTO mode, the windscreen wipers operate

Do not release them while moving them. Risk

panel, accompanied by a message.

automatically and adapt to the intensity of the

of damaging the windscreen!

rainfall.

Switching off

Detection is via a rain/brightness sensor, located

► Clean the windscreen using screenwash

at the top centre of the windscreen behind the

► Give the control stalk another brief push

fluid.

rear view mirror.

downwards or set the control stalk to another

Do not apply "Rain X" type water-

position (Int, 1 or 2).

repellent products.

This indicator lamp goes off on the

instrument panel, accompanied by

a message.

Lighting and visibility

If the ignition has been off for more than

one minute, the automatic wipers must

be reactivated by pushing the control stalk

downwards.

Malfunction

If a fault occurs with the automatic wipers, the

wipers operate in intermittent mode.

Have it checked by a PEUGEOT dealer or a

qualified workshop.

Safety

- As a safety measure, access to the

Declarations of conformity for radio

General safety

diagnostic socket, used for the vehicle's

equipment

recommendations

electronic systems, is reserved strictly for

The relevant certificates are available on the

PEUGEOT dealers or qualified workshops,

http://public.servicebox.peugeot.com/APddb/

Do not remove the labels attached in

equipped with the special tools required (risk

website.

different places on your vehicle. They

of malfunctions of the vehicle's electronic

include safety warnings as well as

systems that could cause breakdowns or

identification information for the vehicle.

serious accidents). The Manufacturer cannot

Emergency or assistance

be held responsible if this advice is not

For all work on your vehicle, use a

followed.

call

qualified workshop that has the technical

- Any modification or adaptation not intended

information, skills and equipment required, all

or authorised by PEUGEOT or carried out

of which a PEUGEOT dealer is able to

without meeting the technical requirements

provide.

defined by the Manufacturer will result in the

suspension of the commercial warranty.

Depending on country regulations,

certain safety equipment may be

Installation of accessory radio

mandatory: high visibility safety vests,

communication transmitters

warning triangles, breathalysers, spare bulbs,

Before installing a radio communication

1. eCall (SOS)

spare fuses, fire extinguisher, first aid kit, mud

transmitter with an external aerial, you must

2. ASSISTANCE

flaps at the rear of the vehicle, etc.

without fail contact a PEUGEOT dealer for

the specification of transmitters which can

Installing electrical accessories:

be fitted (frequency, maximum power, aerial

eCall (SOS)

- The fitting of electrical equipment or

position, specific installation requirements),

Your vehicle may be fitted with the eCall (SOS)

accessories not approved by PEUGEOT may

in line with the Vehicle Electromagnetic

system either as standard or as an option.

cause excessive current consumption and

Compatibility Directive (2004/104/EC).

The eCall (SOS) system provides direct access

faults and failures with the electrical system

to the emergency services and is built directly

of your vehicle. Contact a PEUGEOT dealer

into the vehicle.

for information on the range of approved

According to the country of sale, the eCall (SOS)

accessories.

system corresponds to the systems PE112,

ERAGLONASS, 999, etc.

Safety

The eCall (SOS) system is activated by default.

- The indicator lamp flashes red: replace the

The eCall (SOS) function is only able to

► In an emergency, press button 1 for more

back-up battery.

collect and process the following data

than 2 seconds.

- The indicator lamp is fixed red: system

relating to the vehicle: vehicle identification

The lit indicator lamp and a voice message

malfunction. The emergency and assistance call

number, vehicle type (passenger vehicle or

confirm that the call has been made to the

services may not work.

light commercial vehicle), fuel type or power

emergency services*.

- If the indicator lamp does not come on when

source, three most recent locations and

The eCall (SOS) system immediately locates

the ignition is switched on, this also means that

direction of travel, number of passengers

your vehicle and puts you in contact with the

there is a system malfunction.

and a timestamped log file of the automatic

appropriate emergency services**.

If the problem persists, contact a qualified

activation of the system and its timestamp.

► Pressing again immediately cancels the

workshop as soon as possible.

The recipients of the processed data are the

request.

emergency call handling centres designated

A system fault does not prevent the

The indicator lamp flashes while the vehicle

by the relevant national authorities in the

vehicle from being driven.

data is being sent, and then remains lit when

territory in which they are located, enabling

communication is established.

priority routing and handling of calls to the

Data processing

“112” emergency number.

If an impact is detected by the airbag

All processing of personal data by

control unit, an emergency call is made

the eCall (SOS) function complies with

Data storage

automatically, irrespective of the deployment

the framework for protection of personal

Data contained in the system’s memory

of any airbags.

information established by Regulation

is not accessible from outside the system until

2016/679 (General Data Protection

a call is made. The system is not traceable

This system is a public service and is

Regulation - GDPR) and Directive 2002/58/

and is not continuously monitored in its

free of charge.

EC of the European Parliament and the

normal operating mode.

Council, and in particular, seeks to protect

The data in the system's internal memory is

the vital interests of the data subject, in

Operation of the system

automatically and continuously erased. Only

accordance with Article 6 (1) d) GDPR.

- Upon switching on the ignition, the indicator

the vehicle’s three most recent locations,

The processing of personal data is strictly

lamp lights up red, then green, and then goes

necessary for the normal functioning of the

limited to the purpose of handling the eCall

out: the system is operating correctly.

system, are stored.

(SOS) function used with the “112” single

When an emergency call is triggered, the data

European emergency call number.

log is stored for no more than 13 hours.

* In accordance with the general conditions of use of the service, available from dealers and subject to technological and technical limitations.

** Depending on the geographic coverage of the "eCall (SOS)" and "ASSISTANCE" systems.

The list of countries covered and the telematic services provided is available from dealers or on the website for your country.

Safety

Access to data

Privacy mode allows you to manage the

available to you in your personal space, via

You have the right of access to data and

level of sharing (data and/or location)

the website for your country.

as appropriate to request the rectification,

between your vehicle and PEUGEOT.

For information about the SOS and

erasure or restriction of processing of any

It can be configured in the Settings touch

Assistance Pack, please refer to the general

personal data not processed in accordance

screen menu.

conditions for these services.

with the provisions of GDPR. Third parties

By default, depending on equipment,

to which data has been disclosed shall

deactivate/reactivate geolocation by

be notified of any rectification, erasure or

simultaneously pressing the 2 buttons, then

Hazard warning lamps

restriction carried out in compliance with

press the "ASSISTANCE" button to confirm.

GDPR, unless it proves impossible or

involves a disproportionate effort.

If you purchased your vehicle outside the

You also have the right to lodge a complaint

PEUGEOT dealer network, we invite you

with the respective data protection

to have a dealer check the configuration of

supervisory authority.

these services and, if desired, modify them to

If you want to claim your above-mentioned

suit your wishes. In a multilingual country,

rights please contact us per email at:

configuration is possible in the official national

privacyrights@stellantis.com.

language of your choice.

For more information regarding our contact

► Pressing this red button causes all the

details please take a look at our Privacy &

For technical reasons, in particular to

direction indicators to flash.

Cookies Policy on the brand's website.

improve the quality of telematic services

They can work with the ignition switched off.

for customers, the Manufacturer reserves the

right to carry out updates to the vehicle's

Automatic operation of

ASSISTANCE

on-board telematic system at any time.

hazard warning lamps

► If the vehicle breaks down, press button 2

for more than 2 seconds to request assistance

When braking in an emergency, depending on

(confirmed by a voice message*).

If you benefit from the Peugeot Connect

the rate of deceleration, the hazard warning

► Pressing again immediately cancels the

Packs offer with the SOS and Assistance

lamps come on automatically. They switch off

request.

Pack included, there are additional services

automatically when you next accelerate.

They can be switched off by pressing the button.

* Depending on the geographic coverage of the "eCall (SOS)" and "ASSISTANCE" systems and the official national language chosen by the owner of the

vehicle.

The list of countries covered and the telematic services provided is available from dealers or on the website for your country.

Safety

The fixed illumination of this warning lamp

Horn

Electronic stability control

signals that there is a fault with the ABS.

(ESC)

The vehicle retains conventional braking. Drive

The electronic stability control programme

carefully at a moderate speed.

includes the following systems:

Have it checked by a PEUGEOT dealer or a

- Anti-lock braking system (ABS) and Electronic

qualified workshop.

brake force distribution (EBFD).

This warning lamp, when lit together with

- Emergency braking assistance (EBA).

the STOP and ABS warning lamps,

- Anti-slip regulation (ASR).

accompanied by a message and an audible

- Dynamic stability control (DSC).

signal, indicates an EBFD malfunction.

- Trailer stability assist (TSA).

You must stop the vehicle.

Stop as soon as it is safe to do so and switch off

Anti-lock braking system

the ignition.

► Press the central part of the steering wheel.

Contact a PEUGEOT dealer or a qualified

(ABS)/Electronic brake force

workshop.

Pedestrian horn (Electric)

distribution (EBFD)

When changing wheels (tyres and rims),

This system alerts pedestrians that the vehicle is

These systems enhance the vehicle’s stability

ensure that these are approved for your

approaching.

and handling during braking, and enable greater

vehicle.

The pedestrian horn operates once the vehicle

control while cornering, particularly on poor or

is moving and at speeds of up to 19 mph

slippery road surfaces.

After an impact

(30 km/h), in forward or reverse gear.

ABS prevents wheel locking in the event of

Have it checked by a PEUGEOT dealer

This function cannot be deactivated.

emergency braking.

or a qualified workshop.

Electronic brake force distribution (EBFD)

Malfunction

manages overall braking pressure on each

In the event of a malfunction, this warning

individual wheel.

Emergency braking

lamp lights up on the instrument panel.

► When braking in an emergency, depress

Have it checked by a PEUGEOT dealer or a

assistance (EBA)

the pedal very firmly and maintain this

qualified workshop.

This system reduces the emergency stopping

pressure.

distance, by optimising the braking pressure.

Normal operation of the ABS may make

It is triggered in relation to the speed at which

itself felt by slight vibrations of the brake

the brake pedal is depressed. The effect of this

pedal.

is a reduction in the resistance of the pedal and

an increase in braking efficiency.

Safety

Anti-slip regulation (ASR)

DSC/ASR systems, so that the wheels can move

ASR/DSC

freely and regain grip.

These systems enhance safety during

/ Dynamic stability control

However, it is recommended that the system be

normal driving, but should not encourage

(DSC)

reactivated as soon as possible.

the driver to take extra risks or drive at high

Anti-slip regulation (or traction control) optimises

These systems are reactivated automatically

speed.

traction by using engine braking and by applying

every time the ignition is switched off, or from 31

It is in conditions of reduced grip (rain, snow,

the brakes on the driving wheels to avoid one

mph (50 km/h).

ice) that the risk of loss of grip increases. It

or more wheels spinning. It also enhances the

At speeds below 31 mph (50 km/h), the systems

is therefore important for your safety to keep

vehicle's directional stability.

can be reactivated manually.

these systems activated in all conditions, and

If there is a difference between the vehicle’s

Press this button or turn the thumbwheel

particularly in difficult conditions.

trajectory and the path desired by the driver, the

to this position.

Correct operation of these systems depends

dynamic stability control system automatically

The indicator lamp in the button or thumbwheel

on compliance with the manufacturer's

uses engine braking and the brakes on one or

comes on: the DSC/ASR systems no longer

recommendations relating to the wheels

more wheels to return the vehicle to the desired

have an effect on engine operation.

(tyres and rims), braking and electronic

path, within the limits of the laws of physics.

To reactivate the system:

components, as well as the assembly and

These systems are activated automatically every

Press this button.

repair procedures provided by PEUGEOT

time the vehicle is started.

dealers.

These systems are activated in the event

In order to ensure that these systems remain

of a problem with grip or trajectory

Turn the thumbwheel to this position.

effective in wintry conditions, the use of snow

(confirmed by this warning lamp flashing on the

or all-season tyres is recommended. All four

instrument panel).

The indicator lamp in the button or thumbwheel

wheels must be fitted with tyres approved for

goes off.

your vehicle.

Deactivation / Reactivation

All tyre specifications are listed on the

Malfunction

tyre/paint label. For more information

In the event of a malfunction, this warning

on Identification markings, refer to the

lamp lights up on the instrument panel,

corresponding section.

accompanied by the display of a message and

an audible signal.

Trailer stability assist (TSA)

Have it checked by a PEUGEOT dealer or a

qualified workshop.

When towing, this system reduces the risk of the

vehicle or trailer snaking.

In exceptional conditions (moving a vehicle that

is bogged down in mud, stuck in snow, on loose

soil, etc.), it may prove useful to deactivate the

Safety

Operation

current legislation in force in your country. It

power of the engine. Operation at high engine

The system is activated automatically when the

must not encourage the driver to take extra

speeds is completely normal.

ignition is switched on.

risks, such as using a trailer in unsuitable

A five-position selector knob allows you to

The electronic stability control system (ESC)

conditions of operation (e.g. excessive load,

choose the setting best suited to the driving

must not have any faults.

exceeded nose weight, worn or under-inflated

conditions encountered.

The vehicle speed must be between 37 and 99

tyres, faulty braking system) or driving at

An indicator lamp associated with each mode

mph (60 and 160 km/h).

excessive speed.

comes on, accompanied by the display of a

If the system detects that the trailer is

In certain cases, the system may not detect

message to confirm your choice.

snaking, it applies the brakes to stabilise

trailer snaking, particularly with a light trailer.

When driving on slippery or poor surfaces, the

Operating modes

the trailer and reduces engine power, if

necessary, to slow the vehicle (indicated by the

system may not be able to prevent sudden

flashing of this warning lamp on the instrument

trailer snaking.

panel and the brake lamps coming on).

For information on weights and towed loads,

refer to the Engine technical data and towed

Advanced Grip Control

loads section or your vehicle’s registration

(Depending on version)

certificate.

A special, patented traction control system,

To ensure safe driving with a Towing device,

which improves driveability on snow, mud and

refer to the corresponding section.

sand.

This system, optimised for operation in a range

Malfunction

of conditions, enables you to manoeuvre in most

If a fault occurs, this warning lamp lights

slippery conditions (encountered during normal

up on the instrument panel, accompanied

passenger car use).

by a message and an audible signal.

Standard (ESC)

When combined with all-season M+S (Mud and

To continue towing a trailer, reduce speed and

Snow) tyres, this system offers a compromise

This mode is calibrated for a low level of

drive carefully!

between safety, grip and driveability.

wheel spin, based on the different levels

Have it checked by a PEUGEOT dealer or a

When combined with suitable tyres, this system

of grip normally encountered on the road.

qualified workshop.

offers a compromise between safety, grip and

Whenever the ignition is switched off, the

The trailer stability control system

driveability.

system automatically resets to this mode.

provides an extra safety feature under

The accelerator pedal should be pressed

normal driving conditions, when following the

sufficiently to allow the system to harness the

recommendations for use of trailers and

Safety

Snow

The ASR and DSC systems will no

During a descent, the system assists the driver

This mode adapts its strategy to the

longer act on the operation of the engine

in maintaining a constant speed, depending on

conditions of grip encountered for each of

or of the brakes in the event of a change of

the gear engaged, while progressively releasing

the two front wheels on moving off.

trajectory.

the brakes.

(mode active up to 50 mph (80 km/h))

These systems are reactivated automatically

For the system to activate, the gradient

from 31 mph (50 km/h) and whenever the

must be greater than 5%.

All terrain (mud, damp grass, etc.)

ignition is switched on.

The system can be used with the gearbox in

This mode, when moving off, allows

neutral.

considerable spin on the wheel with the

Recommendations

Otherwise, engage a gear corresponding to

least grip to optimise clearing of the mud and to

Your vehicle is designed principally to

the speed to prevent the engine stalling.

regain grip. At the same time, the wheel with the

drive on tarmac roads but it allows you to

With an automatic gearbox, the system can

most grip is controlled in such a way as to

occasionally drive on other less passable

be used with the selector at N, D or R.

transmit as much torque as possible.

terrain.

When moving, the system optimises wheel spin

However, it does not permit off-road driving

When the system is regulating, the Active

to respond to the driver's requirements as fully

such as:

Safety Brake system is automatically

as possible.

- crossing and driving on terrain which

deactivated.

(mode active up to 31 mph (50 km/h))

could damage the underbody or strip away

components (fuel pipe, fuel cooler, etc.) due

Sand

The system is no longer available if the

to obstacles or stones in particular,

speed of the vehicle is:

This mode allows little spin on the two

- driving on terrain with steep gradients and

- above 43 mph (70 km/h).

driving wheels at the same time to allow

poor grip,

- managed by the Adaptive cruise control,

the vehicle to move forward and limit the risks of

- crossing a stream.

depending on the type of gearbox.

getting stuck in the sand.

(mode active up to 75 mph (120 km/h))

Hill Assist Descent

Switching on

Do not use the other modes on sand as

the vehicle may become stuck.

Control

By default, the system is not selected.

The state of the function is not saved when the

Hill Assist Descent Control system for medium to

ignition is switched off.

Deactivation

steep slopes, on tarmac or other road surfaces

You can deactivate the ASR and DSC

(e.g. gravel, mud).

systems by turning the knob to the "OFF"

This system reduces the risk of slip or loss of

position.

control of the vehicle when descending, whether

going forward or in reverse.

Safety

indicator lamp goes back to grey in the

The front seat belts are fitted with a pyrotechnic

instrument panel, but the green indicator lamp in

pretensioning system and force limiter.

the button remains on.

This system improves safety in the front seats

Regulation resumes automatically when the

in the event of a front or side impact. Depending

speed falls below 19 mph (30 km/h) again, if the

on the severity of the impact, the pyrotechnic

slope and pedal release conditions are met.

pretensioning system instantly tightens the seat

You can depress the accelerator or brake pedal

belts against the body of the occupants.

again at any time.

The pyrotechnic pretensioning seat belts are

enabled when the ignition is on.

Switching off

The force limiter reduces the pressure of the

► To select the system, at speeds below

31 mph (50 km/h), press this button until

► Press the button until its indicator lamp goes

seat belt on the chest of the occupant, thus

its lamp lights up; this indicator lamp appears in

off; the indicator lamp on the instrument panel

improving their protection.

green on the instrument panel.

goes off.

The system becomes active at speeds below 19

At speeds above 43 mph (70 km/h), the system

mph (30 km/h).

is automatically deactivated; the indicator lamp in

The front seat belts are fitted with a single

► When the vehicle begins its descent, the

the button goes off.

pyrotechnic pretensioning system (or double on

driver can release the accelerator and brake

the driver’s side, depending on equipment) and a

pedals; the system regulates the speed:

Malfunction

force limiter (or progressive force limiter on the

- If the gearbox is in first or second gear,

In the event of a malfunction, this warning

driver’s side, depending on equipment options).

the speed decreases and the

lamp comes on in green on the

This system improves safety in the front seats in

indicator lamp flashes rapidly.

instrument panel, accompanied by the display of

the event of a front or side impact.

- If the gearbox is in neutral or if the clutch

a message.

Depending on the severity of the impact, the

pedal is depressed, the speed decreases and

Have it checked by a PEUGEOT dealer or a

single pyrotechnic pretensioning system

the indicator lamp flashes slowly; in this case,

qualified workshop.

instantly tightens the seat belts against the body

the maintained descent speed is lower.

of the occupants.

On a downward slope, with the vehicle

The double pyrotechnic pretensionsining system

Seat belts

stationary, if the driver releases the accelerator

operates the same way, except that it uses two

and brake pedals, the system will release the

anchor points rather than one, for enhanced

brakes to set the vehicle gradually in motion.

Front seat belts

effectiveness.

The brake lamps light up automatically when the

The pyrotechnic pretensioning seat belts are

system is regulating.

enabled when the ignition is on.

If the speed exceeds 19 mph (30 km/h),

regulation is paused automatically, the

Safety

The force limiter reduces the pressure of the

Two-seat front bench seat

seat belt on the chest of the occupant, thus

improving their protection.

The progressive force limiter operates in

the same way, except that it takes the driver’s

stature into consideration, thus optimising the

reduction in the pressure exerted by the seat

belt on the occupant’s chest in the event of an

impact.

Each rear seat is equipped with a seat belt but

Fastening

no pyrotechnic pretensioning system or force

limiter.

Take care to insert each seatbelt into its

matching buckle.

If the vehicle is fitted with a front bench seat,

Do not interchange the belts or buckles for the

ensure that each seat belt is used with its correct

outer seats with the belt or buckle for the centre

buckle.

seat.

Do not interchange the driver's seat belt or

buckle with the centre seat belt or buckle.

Rear seat belts (row 2)

Rear seat belts

► Pull the strap, then insert the tongue into the

buckle.

► Check that the seat belt is fastened correctly

by pulling on the strap.

Unfastening

► Press the red button on the buckle.

► Guide the seat belt as it is reeled in.

100

Safety

Outer seats

Removal and storage

Depending on equipment, they may be fitted with

► Press the red button on buckle B, then the

a single pretensioning system and force limiters.

button on buckle A.

Be sure to put the correct seat belt in the correct

► Guide the strap as it reels in and take tongue

buckle.

B, then A to the magnet at the anchoring point

Do not interchange the belts or buckles for the

on the roof.

outer seats with the belt or buckle for the centre

seat.

Before performing any operations on the

rear seats, to avoid damage to the seat

Centre seat

belts check that the lateral belts are properly

The seat belt does not have a pyrotechnic

tensioned. The central seat belt must be

pretensioning system and force limiters.

completely reeled in.

Installation

Rear seat belts (row 3)

1. Seat belt not fastened/unfastened warning

lamp

► Pull the strap and insert the tongue A into the

2. Front left-hand seat belt not fastened/

right buckle (located on the passenger’s left side

unfastened warning lamp (or driver's seat

when seated in the vehicle).

belt, depending on country of sale).

► Insert the tongue B into the left buckle

These seat belts are not fitted with a pyrotechnic

3. Front right-hand seat belt not fastened/

(located on the passenger’s right side when

pretensioning system or force limiter.

unfastened warning lamp (or driver's seat

seated in the vehicle).

belt, depending on country of sale).

► Check that each buckle is fastened correctly

Seat belt(s) warning lamps

4. Front centre seat belt (row 1) not fastened/

by pulling the strap.

unfastened warning lamp.

5. Rear left-hand seat belt (row 2) not fastened/

unfastened warning lamp.

101

Safety

6. Rear centre seat belt (row 2) not fastened/

Unfastened

The upper part must be positioned in the

unfastened warning lamp.

After the ignition is switched on, warning lamp 1

hollow of the shoulder.

7. Rear right-hand seat belt (row 2) not

(depending on version) and the corresponding

At the front, adjusting the position of the

fastened/unfastened warning lamp.

indicator lamps light up if the driver and/or one or

seat belt may require the seat height to be

adjusted.

more passengers unfasten their seat belts.

Not fastened at the front

In order to be effective, a seat belt must:

At a speed greater than 12 mph (20 km/h), these

When the ignition is switched on, warning lamp

warning lamps flash, accompanied by an audible

- be tightened as close to the body as

1 lights up on the instrument panel (depending

signal for approximately two minutes. After this

possible.

on version) and the corresponding indicator lamp

time, these warning lamps remain on as long as

- be pulled in front of you with a smooth

(2, 3 or 4 (depending on version)) lights up if the

the seatbelts are not refastened.

movement, checking that it is not twisted.

driver and/or front passenger have not fastened

- must only be used to secure one person.

their seat belts.

Advice

- not show signs of tearing or fraying.

At a speed greater than 12 mph (20 km/h),

- not be changed or modified, in order to

The driver must ensure that passengers

avoid affecting its performance.

these warning lamps flash, accompanied by an

use the seat belts correctly and that they

increasing audible signal for approximately two

are all fastened before setting off.

minutes. After two minutes, these warning lamps

Recommendations for children

Wherever seated in the vehicle, you must

remain on as long as the front seatbelts are not

Use a suitable child seat if the passenger

always fasten the seat belt, even for short

fastened.

is less than 12 years old or shorter than 1.5

journeys.

metres.

Not fastened at the rear

Do not invert the seat belt buckles, as they

Never use the same seat belt to secure more

When the ignition is switched on, with the engine

will not fulfil their role properly.

than one child.

running or the vehicle moving at a speed below

To ensure the proper functioning of the belt

Never carry a child on your lap.

12 mph (20 km/h), warning lamp 1 (depending

buckles, make sure that there are no foreign

For more information on Child seats, refer to

on version) and the corresponding indicator

bodies present (e.g. a coin) before fastening.

the corresponding section.

lamps (5 to 7) light up for around sixty seconds,

Before and after use, ensure that the seat belt

if one or more rear seat belts (row 2) are not

is reeled in correctly.

Maintenance

fastened.

After folding or moving a seat or rear bench

In accordance with current safety

seat, ensure that the seat belt is positioned

regulations, for all work on your vehicle's

and reeled in correctly.

seat belts, contact a qualified workshop with

the skills and equipment needed, which a

There are no seat belt warning lamps for

Installation

PEUGEOT dealer is able to provide.

row 3.

The lower part of the strap must be

positioned as low as possible over the pelvis.

102

Safety

Have the seat belts checked regularly by a

airbags supplement the action of the seat belts

Impact detection zones

PEUGEOT dealer or a qualified workshop,

equipped with a force limiting system.

particularly if the straps show signs of

Electronic detectors record and analyse the

damage.

front and side impacts sustained in the impact

Clean the seat belt straps with soapy water or

detection zones:

a textile cleaning product, sold by PEUGEOT

- In the event of violent impact, the airbags

dealers.

deploy instantly and help better protect the

occupants of the vehicle; immediately after the

impact, the airbags deflate rapidly in order not

A. Front impact zone

In the event of an impact

to hinder the visibility or the possible exit of the

B. Side impact zone

Depending on the nature and

seriousness of the impacts, the pyrotechnic

occupants.

- In the event of a slight impact, a rear impact

When one or more airbags are deployed,

device may trigger before and independently

and under certain rollover conditions, the airbags

the detonation of the pyrotechnic charge

of airbag deployment. Deployment of the

may not deploy; only the seat belt helps to

incorporated in the system makes a noise and

pretensioners is accompanied by a slight

protect you in these situations.

releases a small quantity of smoke.

discharge of harmless smoke and a noise,

The seriousness of the impact depends on the

This smoke is not harmful, but sensitive

due to the activation of the pyrotechnic

nature of the obstacle and the speed of the

individuals may experience irritation.

cartridge incorporated in the system.

vehicle at the moment of collision.

The detonation noise associated with the

In all cases, the airbag warning lamp comes

deployment of one or more airbags may result

on.

The airbags do not operate when the

in a slight loss of hearing for a short time.

Following an impact, have the seat belt

ignition is switched off.

system checked, and if necessary replaced,

This equipment will only deploy once. If a

by a PEUGEOT dealer or a qualified

second impact occurs (during the same or a

workshop.

subsequent accident), the airbag will not be

deployed again.

Airbags

General information

This system is designed to improve the safety

of the occupants of the front seats and the rear

outer seats in the event of a violent collision. The

103

Safety

Front airbags

the steering wheel, on the driver's side, and the

Lateral airbags

dashboard, on the passenger's side, to cushion

their forward movement.

This system protects the driver and front

passenger(s) in the event of a serious front

passenger in the event of a serious side impact,

impact, limiting the risk of head and chest injury.

limiting the risk of injury to the chest, between

The driver's airbag is fitted in the centre of the

the hip and the shoulder.

steering wheel; the front passenger airbag is

Each lateral airbag is fitted in the seat backrest

fitted in the roof.

frame, on the door side.

Deployment

The lateral airbags are deployed on one side in

With the two-seat front bench seat, the

When driving, keep the storage

the event of a serious side impact applied to all

passenger sitting in the centre is also protected.

compartment closed. Otherwise, there is

or part of the side impact zone B.

a risk of injury in the event of an accident or

Deployment

sudden braking.

The lateral airbag inflates between the chest of

the vehicle's occupant and the corresponding

They are deployed, except for the front

door panel.

passenger airbag if it is deactivated*, in the

event of a violent front impact applied to all or

Curtain airbags

part of front impact zone A.

The front airbag inflates between the chest and

head of the front occupant of the vehicle and

* For more information on Deactivating the front passenger airbag, refer to the corresponding section.

104

Safety

If fitted to the vehicle, this system offers

Contact a PEUGEOT dealer or a qualified

discharging the hot gas via openings provided

enhanced protection for the driver and

workshop to have the system checked.

for this purpose.

passenger in the event of a serious side impact,

The airbags may not be deployed in the event of

After an accident or if the vehicle has been

limiting the risk of injury to the side of the head.

a serious impact.

stolen, have the airbag systems checked.

Each curtain airbag is built into the pillars and

All work must be carried out only by a

In the event of a minor impact or bump at

the upper passenger compartment area.

PEUGEOT dealer or a qualified workshop

the side of the vehicle or if the vehicle

With the two-seat front bench seat, the

rolls over, the airbags may not be deployed.

Front airbags

passenger sitting in the centre is not

In the event of a rear or front collision, none of

Do not drive holding the steering wheel

protected.

the lateral airbags are deployed.

by its spokes or resting your hands on the

centre part of the wheel.

Advice

Passengers must not place their feet on the

dashboard.

If fitted to the vehicle, this system offers

For the airbags to be fully effective,

Do not smoke as deployment of the airbags

enhanced protection for the driver and

observe the safety recommendations

can cause burns or the risk of injury from a

passengers (except in the central seats) in the

below.

cigarette or pipe.

event of a serious side impact, limiting the risk of

Adopt a normal and upright sitting position.

Never remove or pierce the steering wheel or

injury to the side of the head.

Fasten your seat belt and position it correctly.

hit it violently.

Each curtain airbag is built into the pillars and

Do not place anything between the occupants

Do not fix or attach anything to the steering

the upper passenger compartment area.

and the airbags (e.g. child, animal, object), do

wheel or dashboard, as this could cause

not fix or attach anything near or in the path of

Deployment

injuries when the airbags are deployed.

the airbags, as this could cause injuries when

It deploys simultaneously with the corresponding

they are deployed.

lateral airbag in the event of a serious side

Lateral airbags

Do not place objects on the dashboard.

impact applied to all or part of the side impact

Use only approved seat covers

Never modify the original definition of the

zone B.

compatible with the deployment of these

vehicle, particularly in the area directly around

The curtain airbag inflates between the front

airbags. For information on the range of seat

the airbags.

and rear occupants of the vehicle and the

covers suitable for your vehicle, contact a

Even if all of the precautions mentioned are

corresponding windows.

PEUGEOT dealer.

observed, a risk of injury or of minor burns to

Do not fix or attach anything to the seat

the head, chest or arms cannot be ruled out

Malfunction

backrests (e.g. clothing) as this could cause

when an airbag is deployed. The bag inflates

injuries to the chest or arm when the airbag is

In the event of a malfunction, this warning

almost instantly (within a few milliseconds)

deployed.

lamp lights up on the instrument panel.

then deflates within the same time,

105

Была ли эта страница вам полезна?

Да!Нет

7 посетителей считают эту страницу полезной.

Peugeot Partner (2022 year). Manual in english — page 5

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.