Peugeot 308 (2022 year). Manual in english — page 5
Safety
Seat belt not fastened/
When the ignition is switched on, if one of the
Advice
5
rear passengers has not fastened their seat
unfastened alerts
belt, the corresponding warning lamp (3, 4 or 5)
The driver must ensure that passengers
comes on in red for 1 minute.
use the seat belts correctly and that they
Seat belt unfastened alert
are all fastened before setting off.
After the ignition is switched on, if the
Wherever seated in the vehicle, you must
driver or a passenger unfastens their seat belt,
always fasten the seat belt, even for short
the corresponding warning lamp (1, 2, 3, 4 or
journeys.
5) comes on in red. At a speed greater than
Do not invert the seat belt buckles, as they
12 mph (20 km/h), the warning lamp flashes,
will not fulfil their role properly.
accompanied by an audible signal for around 2
To ensure the proper functioning of the belt
minutes. After this time has elapsed, the warning
buckles, make sure that there are no foreign
1. Front left seat belt warning lamp
lamp remains on until the seat belt has been
bodies present (e.g. a coin) before fastening.
2. Front right seat belt warning lamp
fastened again.
Before and after use, ensure that the seat belt
3. Rear left seat belt warning lamp
With the ignition on, if the driver or a
is reeled in correctly.
4. Rear centre seat belt warning lamp
passenger fastens their seat belt, the
After folding or moving a seat or rear bench
5. Rear right seat belt warning lamp
corresponding warning lamp (1, 2, 3, 4 or 5)
seat, ensure that the seat belt is positioned
Not fastened/unfastened warning lamp
comes on in green on the display.
and reeled in correctly.
It comes on in red on both the instrument panel
With the ignition on, if one of the front or
and on the seat belts warning lamps display as
rear passenger seats is detected as being
Installation
soon as the system detects that a seat belt is not
unoccupied, the corresponding warning lamp (2,
The lower part of the strap must be
fastened or has been unfastened.
3, 4 or 5) comes on in grey on the display.
positioned as low as possible over the pelvis.
Front seat belt not fastened alert
When there are no longer any not fastened/
The upper part must be positioned in the
When the ignition is switched on, if the
unfastened alerts, the green or grey warning
hollow of the shoulder.
driver or front passenger has not fastened their
lamps remain on for around 30 seconds, then
At the front, adjusting the position of the
seat belt, the corresponding warning lamp (1 or
go off.
seat belt may require the seat height to be
2) comes on in red. At a speed greater than 12
adjusted.
mph (20 km/h), the warning lamp flashes red,
In order to be effective, a seat belt must:
accompanied by an audible signal for around 2
- be tightened as close to the body as
minutes. After this time has elapsed, the warning
possible.
lamp remains on fixed in red until the seat belt is
- be pulled in front of you with a smooth
fastened.
movement, checking that it is not twisted.
Rear seat belt not fastened alert
- must only be used to secure one person.
85
Safety
- not show signs of tearing or fraying.
Impact detection zones
Airbags
- not be changed or modified, in order to
avoid affecting its performance.
General information
System designed to help improve the safety
Recommendations for children
of the occupants sitting in the front seats and
Use a suitable child seat if the passenger
the rear outer seats, in the event of a violent
is less than 12 years old or shorter than 1.5
collision. The airbags supplement the action
metres.
of the seat belts equipped with a force limiting
A. Front impact zone
Never use the same seat belt to secure more
system.
B. Side impact zone
than one child.
Electronic detectors record and analyse the
Never carry a child on your lap.
front and side impacts sustained in the impact
When one or more airbags are deployed,
For more information on Child seats, refer to
detection zones:
the detonation of the pyrotechnic charge
the corresponding section.
- In the event of violent impact, the airbags
incorporated in the system makes a noise and
deploy instantly and help better protect the
releases a small quantity of smoke.
Maintenance
occupants of the vehicle; immediately after the
This smoke is not harmful, but sensitive
In accordance with current safety
impact, the airbags deflate rapidly in order not
individuals may experience irritation.
regulations, for all work on your vehicle's
to hinder the visibility or the possible exit of the
The detonation noise associated with the
seat belts, contact a qualified workshop with
occupants.
deployment of one or more airbags may result
the skills and equipment needed, which a
- In the event of a slight impact, a rear impact
in a slight loss of hearing for a short time.
PEUGEOT dealer is able to provide.
and under certain rollover conditions, the airbags
Have the seat belts checked regularly by a
may not deploy; only the seat belt helps to
PEUGEOT dealer or a qualified workshop,
protect you in these situations.
particularly if the straps show signs of
The seriousness of the impact depends on the
damage.
nature of the obstacle and the speed of the
Clean the seat belt straps with soapy water or
vehicle at the moment of collision.
a textile cleaning product, sold by PEUGEOT
dealers.
The airbags do not operate when the
ignition is switched off.
This equipment will only deploy once. If a
second impact occurs (during the same or a
subsequent accident), the airbag will not be
deployed again.
86
Safety
Front airbags
Lateral airbags
Curtain airbags
5
System contributing towards greater protection
for the driver and passengers (with the exception
of the rear centre passenger) in the event of a
serious side impact in order to limit the risk of
injury to the side of the head.
Each curtain airbag is built into the pillars and
the upper passenger compartment area.
Deployment
It deploys simultaneously with the corresponding
lateral airbag in the event of a serious side
impact applied to all or part of the side impact
System that protects the driver and front
In the event of a serious side impact, this system
zone B.
passenger in the event of a serious front impact,
protects the driver and front passenger to
The curtain airbag inflates between the front
limiting the risk of head and chest injury.
mitigate the risk of injury to the chest, between
and rear occupants of the vehicle and the
The driver's airbag is fitted in the centre of the
the hip and the shoulder.
corresponding windows.
steering wheel; the front passenger airbag is
Each lateral airbag is fitted in the seat backrest
fitted in the dashboard above the glove box.
frame, on the door side.
Malfunction
Deployment
In the event of a malfunction,
Deployment
They deploy, except the front passenger airbag
these warning lamps light up on
The lateral airbags are deployed on one side in
if it is deactivated*, in the event of a serious front
the instrument panel. Contact a PEUGEOT
the event of a serious side impact applied to all
impact to all or part of the front impact zone A.
dealer or a qualified workshop to have the
or part of the side impact zone B.
The front airbag inflates between the thorax and
system checked.
The lateral airbag inflates between the chest of
head of the front occupant of the vehicle and the
The airbags may not be deployed in the event of
the vehicle's occupant and the corresponding
steering wheel, driver's side, and the dashboard,
a serious impact.
door panel.
passenger's side, to cushion their forward
movement.
* For more information on Deactivating the front passenger airbag, refer to the corresponding section.
87
Safety
In the event of a minor impact or bump at
Front airbags
sensors - risk of malfunction of the lateral
the side of the vehicle or if the vehicle
Do not drive holding the steering wheel
airbags!
rolls over, the airbags may not be deployed.
by its spokes or resting your hands on the
All work must be carried out only by a
In the event of a rear or front collision, none of
centre part of the wheel.
PEUGEOT dealer or a qualified workshop
the lateral airbags are deployed.
Passengers must not place their feet on the
dashboard.
Curtain airbags
Do not smoke as deployment of the airbags
Do not fix or attach anything to the roof,
Advice
can cause burns or the risk of injury from a
as this could cause head injuries when the
For the airbags to be fully effective,
cigarette or pipe.
curtain airbag is deployed.
observe the safety recommendations
Never remove or pierce the steering wheel or
Do not remove the grab handles installed on
below.
hit it violently.
the roof.
Do not fix or attach anything to the steering
Adopt a normal and upright sitting position.
wheel or dashboard, as this could cause
Fasten your seat belt and position it correctly.
injuries when the airbags are deployed.
Do not place anything between the occupants
Child seats
and the airbags (e.g. child, animal, object), do
not fix or attach anything near or in the path of
Lateral airbags
The legislation on carrying children is
the airbags, as this could cause injuries when
Use only approved seat covers
specific to each country. Refer to the
they are deployed.
compatible with the deployment of these
legislation in force in your country.
Never modify the original definition of the
airbags. For information on the range of seat
vehicle, particularly in the area directly around
covers suitable for your vehicle, contact a
For maximum safety, please observe the
the airbags.
PEUGEOT dealer.
following recommendations:
Even if all of the precautions mentioned are
Do not fix or attach anything to the seat
- In accordance with European regulations, all
observed, a risk of injury or of minor burns to
backrests (e.g. clothing) as this could cause
children under the age of 12 or less than one
the head, chest or arms cannot be ruled out
injuries to the chest or arm when the airbag is
and a half metres tall must travel in approved
when an airbag is deployed. The bag inflates
deployed.
child seats suited to their weight, on seats
almost instantly (within a few milliseconds)
Do not sit with the upper part of the body any
fitted with a seat belt or ISOFIX mountings.
then deflates within the same time,
nearer to the door than necessary.
- Statistically, the safest seats in your
discharging the hot gas via openings provided
The vehicle's front door panels include side
vehicle for carrying children are the rear
for this purpose.
impact sensors.
seats.
After an accident or if the vehicle has been
A damaged door or any unauthorised or
- A child weighing less than 9 kg must travel
stolen, have the airbag systems checked.
incorrectly executed work (modification or
in the "rearward facing" position both in the
All work must be carried out only by a
repair) on the front doors or their interior trim
front and in the rear.
PEUGEOT dealer or a qualified workshop
could compromise the operation of these
88
Safety
It is recommended that children travel
thrown around the vehicle in the event of
Child seat at the rear
5
on the rear seats of the vehicle:
sharp braking. Refit the head restraint once
- "rearward facing" up to the age of 3,
the child seat has been removed.
Forward-facing or rearward-facing
- "forward facing" over the age of 3.
Installing a booster seat
Make sure that the seat belt is correctly
The chest part of the seat belt must be
positioned and tightened.
positioned on the child's shoulder without
For child seats with a support leg, ensure that
touching the neck.
the support leg is in firm and steady contact
Ensure that the lap part of the seat belt
with the floor.
passes correctly over the child's thighs.
Use a booster seat with a backrest, equipped
An incorrectly installed child seat in a
with a belt guide at shoulder level.
vehicle compromises the child's safety in
► Move the vehicle's front seat forward and
the event of an accident.
Additional protections
straighten the backrest so that the legs of the
Ensure that there is no seat belt or seat belt
To prevent accidental opening of the
child in the forward-facing or rearward-facing
buckle under the child seat, as this could
doors and rear windows, use the "Child lock".
child seat itself do not touch the vehicle's front
destabilise it.
Take care not to open the rear windows by
seat.
Remember to fasten the seat belts or the
more than one third.
► Check that the backrest of the forward-facing
child seat harness keeping the slack relative
To protect young children from the sun's rays,
child seat is as close as possible to the backrest
to the child's body to a minimum, even for
fit side blinds on the rear windows.
of the vehicle's rear seat, and ideally in contact
short journeys.
As a safety measure, do not leave:
with it.
When installing a child seat using the seat
- A child alone and unsupervised inside a
belt, ensure that the seat belt is tightened
vehicle.
Centre rear seat
correctly on the child seat and that it secures
- A child or an animal in a vehicle which is
A child seat with a support leg must never be
the child seat firmly on the vehicle seat. If
exposed to the sun, with the windows closed.
installed on the centre rear passenger seat.
the passenger seat is adjustable, move it
- The keys within reach of children inside the
forwards if necessary.
vehicle.
Remove the head restraint before
installing a child seat with a backrest on a
passenger seat.
Ensure that the head restraint is stored or
attached securely to prevent it from being
89
Safety
Child seat at the front
The front passenger airbag must be
Deactivating the front
deactivated before installing a rearward
passenger airbag
facing child seat. Otherwise, the child risks
being seriously injured or killed if the
airbag is deployed.
► Adjust the front passenger seat to the
Passenger airbag OFF
highest and fully back longitudinal position,
with the backrest straightened.
To ensure the safety of the child, the front
passenger airbag MUST be deactivated
"Forward facing"
when a "rearward facing" child seat is
installed on the front passenger seat.
Otherwise, the child risks being seriously
injured or killed in the event of deployment of
Warning label - Front passenger airbag
the airbag.
Vehicles not equipped with a
deactivation/reactivation control
Installing a "rearward facing" child seat on
You must leave the front passenger
the front passenger seat is strictly prohibited
airbag active.
- risk of death or serious injury in the event of
airbag deployment!
"Rearward facing"
You must comply with the following instruction,
Deactivating/Reactivating the front
as reminded by the warning label on both sides
passenger airbag
of the passenger sun visor:
For vehicles on which it is fitted, the switch is
NEVER use a rearward facing child restraint
located on the side of the dashboard.
on a seat protected by an ACTIVE AIRBAG in
front of it, DEATH or SERIOUS INJURY to the
CHILD can occur.
90
Safety
Group 0+: from birth to 13 kg
Groups 2 and 3: from 15 to 36 kg
5
L1
L6
"RÖMER Baby-Safe"
"GRACO Booster"
Installed in the "rearward facing" position.
The child is restrained by the seat belt.
Only suitable for installation on the front
Groups 2 and 3: from 15 to 36 kg
passenger seat or on the rear side seats.
With the ignition off:
► To deactivate the airbag, turn the key in the
"ISOFIX" mountings
switch to the "OFF" position.
► To reactivate it, turn the key to the "ON"
The seats shown below are fitted with ISOFIX
position.
compliant mountings:
When the ignition is switched on:
This warning lamp comes on and remains
L5
lit to signal deactivation.
"RÖMER KIDFIX 2R"
Or
Can be fitted to the vehicle's ISOFIX
This warning lamp comes on for about 1
mountings.
minute to signal activation.
The child is restrained by the seat belt.
Only suitable for installation on the side rear
Recommended child seats
seats.
The head restraint on the vehicle seat must
The mountings comprise three rings for each
Range of child seats secured using a three-
be removed.
seat, indicated by a marking:
point seat belt.
- Two rings A, located between the vehicle seat
backrest and cushion.
91
Safety
► Remove and stow the head restraint before
"RÖMER Baby-Safe and its ISOFIX base"
installing the child seat on this seat (refit it once
(size category: E)
the child seat has been removed).
► Pass the strap of the child seat behind the
Group 0+: from birth to 13 kg
seat backrest, centring it between the openings
for the head restraint rods.
► Secure the upper strap hook to ring B.
► Tighten the upper strap.
Installed "rearward facing" using an ISOFIX
When fitting an ISOFIX child seat to the
base which is attached to rings A.
These rings are located behind zips.
left-hand rear seat of the bench seat,
The base has a support leg, height-
The 2 latches on ISOFIX child seats are
before fitting the seat, first move the centre
adjustable, which rests on the vehicle's floor.
secured to them.
rear seat belt towards the middle of the
This child seat can also be secured with a
- One ring B, located behind the seat, called the
vehicle, so as to avoid the seat interfering
seat belt. In this case, only the shell is used
TOP TETHER, for attaching seats fitted with an
with the operation of the seat belt.
and attached to the vehicle seat using the
upper strap.
three-point seat belt.
An incorrectly installed child seat in a
vehicle compromises the child's safety in
the event of an accident.
"RÖMER Duo Plus ISOFIX"
Strictly observe the fitting instructions
(size category: B1)
provided in the user guide supplied with the
Group 1: from 9 to 18 kg
child seat.
For information about the options for
fitting ISOFIX child seats in your vehicle,
refer to the summary table.
This system prevents the child seat from tipping
forwards in the event of a front impact.
This ISOFIX mounting system provides fast,
Recommended ISOFIX child seats
reliable and safe fitting of the child seat in the
vehicle.
Also consult the user guide from the child
To secure the child seat to the TOP TETHER:
seat’s manufacturer to find out how to
install and remove the seat.
92
Safety
"RÖMER Duo Plus ISOFIX"
5
(size category: B1)
Group 1: from 9 to 18 kg
Suitable for forward-facing installation only.
Attached to rings A and ring B, referred to as
TOP TETHER, using an upper strap.
Three seat body angles: sitting, reclining,
lying down.
This child seat can also be used in seat
positions not equipped with ISOFIX
mountings. In this case, it must be secured to
the vehicle's seat by the three-point seat belt.
Adjust the front seat of the vehicle so that the
child's feet do not touch the backrest.
i-Size child seats
i-Size child seats have two latches that engage on the two rings A.
These i-Size child seats also have:
- either an upper strap that is attached to ring B.
- or a support leg that rests on the vehicle floor, compatible with the approved i-Size seat position.
Their role is to prevent the child seat from tipping forward in the event of a collision.
For more information on the ISOFIX mountings, refer to the corresponding section.
Installing universal, ISOFIX and i-Size child seats
In compliance with European regulations, this table indicates the options for installing child seats secured using the seat belt and universally approved (a)
as well as the largest ISOFIX and i-Size child seats for the seat positions fitted with ISOFIX anchorage points in the vehicle.
93
Safety
Seat number
Front seats
Rear seats
(d)
(d)
1
3
4
5
6
3
1
4
5
6
Front passenger airbag
Deactivated "OFF"
Activated "ON" (c)
(b)
Position compatible with a universal (a)
no
yes (f) (i)
yes (f) (j)
yes
yes (e)
yes
child seat
Position compatible with an i-Size child
no
no
yes
no
yes
seat
Position equipped with a Top Tether hook
no
no
yes
no
yes
"Carrycot" type child seat
no
no
no
no
no
"Rearward facing" ISOFIX child seat
no
no
no
R3 (g) (h)
no
R3 (g) (h)
"Forward facing" ISOFIX child seat
no
no
F3
no
F3
Child booster seat
no
B3
B3
no
B3
Rules:
- A position that is F3 compatible is also
(a) Universal child seat: child seat that can be
- A position that is i-Size compatible is also
compatible with F2X and F2.
installed in all vehicles using the seat belt.
compatible with R1, R2 and F2X, F2, B2.
- A position that is B3 compatible is also
(b) To install a "rearward facing" child seat at
- A position that is R3 compatible is also
compatible with B2.
this seat position, the front passenger airbag
compatible with R1 and R2.
must be deactivated ("OFF").
94
Safety
(c)
Only a "forward facing" child seat is
and universally approved "rearward facing"
5
authorised at this seat position with the front
and/or "forward facing" (U) for all sizes and
passenger airbag activated ("ON").
weight groups.
Seat position suitable for the installation
(d)
Depending on version, refer to the
of a child seat secured using the seat belt
legislation in force in your country before
and universally approved "forward facing"
installing a child in this seat position.
(UF) for groups 1, 2 & 3 only.
(e)
Never install a child seat with a support leg
Seat position authorised for the
on the centre rear seat.
installation of an i-Size child seat.
Seat position not suitable for the
(f)
For a seat with height adjustment, adjust
installation of a child seat with support
the seat to the highest position and move it
leg.
fully back.
Presence of a Top Tether anchorage
(g)
Adjust the driver's seat to the highest
point at the rear of the backrest,
position.
authorising the installation of a universal ISOFIX
child seat.
(h)
Adjust the passenger seat to the
"Rearward facing" ISOFIX child seat:
intermediate forward longitudinal position.
(i)
For a universal "rearward facing" and/or
- R1: ISOFIX child seat for a baby.
"forward facing" (U) child seat in groups 0,
- R2: ISOFIXreduced size child seat.
0+, 1, 2 or 3.
- R3: ISOFIXlarge size child seat.
"Forward facing" ISOFIX child seat:
(j)
For a universal "forward facing" (UF) child
seat in groups 1, 2 or 3.
- F2X: ISOFIX child seat for toddlers.
Key
- F2: ISOFIXreduced height child seat.
Seat position where the installation of a
- F3: ISOFIXfull height child seat.
child seat is forbidden.
Booster child seat:
Front passenger airbag deactivated.
- B2: reduced width booster seat.
Front passenger airbag activated.
- B3: full width booster seat.
Seat position where the installation of an
Seat position suitable for the installation
ISOFIX child seat is forbidden.
of a child seat secured using the seat belt
95
Safety
For seat adjustments, refer to the table
"Installing universal, ISOFIX and i-Size child
seats".
Manual child lock
The system prevents a rear door from being
opened using its interior handle.
The control is located on the edge of each rear
door (marked by a label on the bodywork).
Activation/Deactivation
► To activate, turn the built-in key fully:
• To the right on the left-hand rear door.
• To the left on the right-hand rear door.
► To deactivate, turn it in the opposite direction.
96
Driving
Driving recommendations
Never park the vehicle and never
On flooded roads
6
leave the engine running on a
We strongly advise against driving on flooded
► Observe the driving regulations and remain
flammable surface (e.g. dry grass, dead
roads, as this could cause serious damage to
vigilant whatever the traffic conditions.
leaves).The vehicle exhaust system is very
the internal combustion engine or electric motor,
► Monitor your environment and keep your
hot, even several minutes after the engine
the gearbox and the electrical systems of the
hands on the wheel to be able to react to
stops. Risk of fire!
vehicle.
anything that may happen any time.
► Drive smoothly, anticipate the need for
Never drive on surfaces covered with
braking and maintain a longer safety distance,
vegetation (e.g. tall grass,
especially in bad weather.
accumulated dead leaves, crops, debris)
► Stop the vehicle before performing operations
such as a field, a country lane overgrown
that require sustained attention (e.g. settings).
with bushes or a grassy verge.
► During long trips, take a break every 2 hours.
This vegetation could come into contact with
the vehicle's exhaust system or other systems
Important!
If the vehicle absolutely must drive through a
which are very hot. Risk of fire!
flooded section of road:
Never leave the engine running in a
► Check that the depth of the water does not
closed space without sufficient
Make sure you do not leave any item in
exceed 15 cm, taking account of waves that
ventilation. Internal combustion engines emit
the passenger compartment which could
might be generated by other users.
toxic exhaust gases such as carbon
act like a magnifying glass under the effect of
► Deactivate the Stop & Start function.
monoxide. Danger of poisoning and death!
the sun's rays and cause a fire. Risk of fire or
► Drive as slowly as possible without stalling. In
damage to interior surfaces!
all cases, do not exceed 6 mph (10 km/h).
In very severe wintry conditions
► Do not stop and do not switch off the engine.
(temperature below -23°C), let the engine
Never leave the vehicle unattended,
On leaving the flooded road, as soon as safety
run for 4 minutes before moving off, to ensure
with the engine running. If you have to
conditions allow, make several light brake
the correct operation and durability of the
leave your vehicle with the engine running,
applications to dry the brake discs and pads.
mechanical components of your vehicle
apply the parking brake and put the gearbox
If in doubt about the state of your vehicle,
(engine and gearbox).
into neutral or position N or P (depending on
contact a PEUGEOT dealer or a qualified
the type of gearbox).
workshop.
Never drive with the parking brake
applied. Risk of overheating and
Never leave children inside the vehicle
damaging the braking system!
unsupervised.
97
Driving
Towing
Tyres
Brakes
► Check the tyre pressures of the towing
Using the engine brake is recommended to limit
Driving with a trailer places greater
vehicle and of the trailer, observing the
the overheating of the brakes. Braking distances
demands on the towing vehicle and
recommended pressures.
are increased when towing a trailer.
particular care must be taken.
Lighting
Side wind
► Check the electrical signalling on the trailer
Bear in mind that the vehicle will be more
Do not exceed the maximum towable
and the headlamp beam height of your vehicle.
susceptible to wind when towing.
weights.
At altitude: reduce the maximum load by
If a genuine PEUGEOT towing device is
10% per 1,000 metres of altitude; the lower
used, the rear parking sensors will be
Anti-theft protection
air density at high altitudes decreases engine
deactivated automatically to avoid the audible
performance.
signal.
Electronic immobiliser
The keys contain a code, which must be
New vehicle: do not tow a trailer until the
When driving
recognised by the vehicle before starting is
vehicle has driven at least 620 miles
possible.
(1,000 kilometres).
Cooling
If the system malfunctions, indicated by the
Towing a trailer uphill causes the coolant
display of a message, the engine will not start.
If the outside temperature is high, let the
temperature to increase. The maximum towable
Contact a PEUGEOT dealer.
engine idle for 1 to 2 minutes after the
load depends on the gradient and the exterior
vehicle comes to a stop, to help it to cool.
temperature. The fan’s cooling capacity does not
increase with engine speed.
► Reduce speed and lower the engine speed to
Before setting off
limit the amount of heating produced.
Nose weight
► Pay constant attention to the coolant
► Distribute the load in the trailer so that the
temperature.
heaviest items are as close as possible to the
If this warning lamp and the STOP
axle and the nose weight (at the point where it
warning lamp come on, stop the
joins your vehicle) approaches the maximum
vehicle and switch off the engine as soon as
permitted without exceeding it.
possible.
98
Driving
Ignition on position
vibrations, for anything up to 2 minutes
Starting / Switching off the
6
(accelerated idle speed).
It allows the use of the vehicle's electric
engine with the key
equipment or the charging of accessories.
► With a Diesel engine, turn the key to position
Once the state of charge of the battery drops to
2, to activate the engine preheating system.
Key ignition switch
the reserve level, the system switches to energy
Wait until this warning lamp goes off on
economy mode. The power supply is cut off
the instrument panel, then turn the key to
automatically to preserve the remaining battery
position 3 without pressing the accelerator pedal,
charge.
to operate the starter motor. Once the engine
has started, release the key and allow it to return
Starting the engine
to position 2.
With the parking brake applied:
► With a manual gearbox, place the gear lever
In wintry conditions, the warning lamp
in neutral then fully depress the clutch pedal.
may stay on for a longer period. When
► With an automatic gearbox, place the gear
the engine is hot, the warning lamp does not
selector in mode N or P then depress the brake
come on.
pedal.
In mild conditions, do not leave the engine
It has 3 positions:
► Insert the key into the ignition switch; the
to warm up while stationary, but move off
1. Stop
system recognises the code.
straight away and drive at moderate speed.
Inserting/removing the key, steering column
► Unlock the steering column by simultaneously
locked.
turning the steering wheel and the key.
If the engine does not start straight away,
2. Ignition on
switch off the ignition. Wait a few
In certain cases, you may need to apply
Steering column unlocked, ignition on,
seconds before operating the starter motor
significant force to move the steering
preheating (Diesel), switching the engine on.
again. If the engine does not start after a few
wheel (e.g. wheels turned to full lock).
3. Starting
attempts, do not keep trying - risk of
► With a petrol engine, operate the starter
damaging the starter motor and the engine!
Avoid attaching heavy objects to the key
Contact a PEUGEOT dealer or a qualified
motor by turning the key to position 3 without
or the remote control. This would weigh
workshop.
pressing the accelerator pedal, until the engine
down on its shaft in the ignition switch and
starts. Once the engine has started, release the
could cause a malfunction.
key and allow it to return to position 2.
Switching off the engine
Petrol engines
► Immobilise the vehicle.
After a cold start, preheating the catalytic
► With the engine at idle, turn the key to
converter can cause noticeable engine
position 1.
99
Driving
► Remove the key from the ignition switch.
Key left in
Starting
► To lock the steering column, turn the steering
When the driver's door is opened, a
wheel until it locks.
message is displayed, accompanied by an
audible signal, if the key has been left in the
To facilitate unlocking of the steering
ignition switch in position 1.
column, it is recommended that the
If the key has been left in the ignition switch
wheels be returned to the straight ahead
in position 2, the ignition will be switched off
position before switching off the engine.
automatically after one hour.
To switch the ignition back on, turn the key to
Never switch off the ignition before the
position 1, then back to position 2.
complete immobilisation of the vehicle.
With the engine off, the braking and steering
assistance systems are also cut off - risk of
► With a manual gearbox, place the gear lever
Starting/Switching off the
loss of control of the vehicle!
in neutral and fully depress the clutch pedal.
engine with Keyless Entry
► With an automatic gearbox, select mode P
Check that the parking brake is correctly
or N and press the brake pedal.
and Start
applied, particularly on sloping ground.
► Press the "START/STOP" button while
When leaving the vehicle, keep the key in
maintaining pressure on the pedal until the
The electronic key must be present in the
your possession and lock the vehicle.
engine starts.
passenger compartment.
Diesel engines
The electronic key is also detected in the
In negative temperatures and/or when the
boot.
Energy economy mode
engine is cold, starting takes place only after the
If the electronic key is not detected, a
After the engine has stopped (position 1. Stop),
preheating warning lamp goes out.
message is displayed.
for a maximum combined duration of 40 minutes,
If this warning lamp comes on after
Move the electronic key so that the engine
you can still use functions such as the audio and
pressing the "START/STOP" button:
can be started or switched off.
telematics system, courtesy lamps or dipped
► Keep the pedal fully depressed and do not
If there is still a problem, refer to the "Key
beam headlamps.
press the "START/STOP" button again until the
not detected - Back-up starting or Back-up
engine is running.
For more information on Energy
switch-off" section.
In all circumstances, if one of the starting
economy mode, refer to the
conditions is not met, a message is displayed.
corresponding section.
In some circumstances, a message indicates
that it is necessary to turn the steering wheel
100
Driving
while pressing the "START/STOP" button to
When the vehicle starts in electric mode,
Switching on the ignition
6
assist unlocking of the steering column.
it makes no noise.
without starting the engine
Pay particular attention to pedestrians and
Petrol engines
cyclists who may not hear the vehicle coming
With Petrol engines, after a cold start,
despite the pedestrian horn.
pre-heating the catalytic converter can cause
noticeable engine vibrations, for anything up
to 2 minutes (accelerated idle speed).
Switching off
► Deactivate cruise control alone or Drive
If the engine stalls, release the clutch
Assist Plus (depending on version).
pedal and fully depress it again, the
► Immobilise the vehicle using the parking
engine will restart automatically.
brake.
► With a manual gearbox, ideally put the gear
lever into neutral.
Starting rechargeable hybrid
With the electronic key in the passenger
► With an automatic gearbox, ideally select
compartment, pressing the "START/STOP"
vehicles
mode P or N.
button, without depressing any of the pedals,
► Fully depress the brake pedal and press
► Press the "START/STOP" button.
allows the ignition to be switched on without
the START/STOP button for approximately 2
► For rechargeable hybrid vehicles, before
starting the engine.
seconds.
leaving the vehicle, check that the READY
► Press this button again to switch off the
► Keep your foot on the pedal until this
indicator lamp is switched off.
ignition and allow the vehicle to be locked.
indicator lamp comes on, indicating the
The automatic gearbox locks in mode P.
activation of the rechargeable hybrid system
In some circumstances, it is necessary to turn
Key not detected
(confirmed by an audible signal).
the steering wheel to lock the steering column.
To exit Park mode, wait for the READY
If the vehicle is not immobilised, the
Back-up starting
indicator lamp to come on.
engine will not stop.
A back-up reader is fitted to the steering column,
to enable the engine to be started if the system
By default, the system starts in Electric mode.
fails to detect the key in the recognition zone, or
With the engine off, the braking and
Depending on certain parameters (battery
if the battery in the electronic key is flat.
steering assistance systems are also cut
charge level or outside temperature), the system
off - risk of loss of control of the vehicle!
determines whether it is necessary to start the
petrol engine.
Never leave your vehicle with the
It is possible to change the driving mode at any
electronic key still inside.
time using the mode selector.
101
Driving
► To confirm the instruction to switch off the
► To release it, briefly push the control while
engine, press the "START/STOP" button for
pressing the brake pedal.
approximately 5 seconds.
Automatic mode is activated by default.
In the event of a fault with the electronic key,
This automatic operation can be deactivated in
contact a PEUGEOT dealer or a qualified
certain situations.
workshop.
Indicator lamp
► Place and hold the remote control against the
Emergency switch-off
This indicator lamp comes on both on the
back-up reader.
In case of emergency only, the engine can be
instrument panel and on the control to
► With a manual gearbox, place the gear lever
switched off without conditions (even when
confirm that the parking brake has been applied,
in neutral, then fully depress the clutch pedal.
driving).
accompanied by display of the message
► With an automatic gearbox, select mode P,
► Press the "START/STOP" button for about
"Parking brake applied".
then depress the brake pedal.
5 seconds.
The indicator lamp goes out to confirm the
► Press the "START/STOP" button.
In this case, the steering column locks as soon
release of the parking brake, accompanied by
The engine starts.
as the vehicle stops.
the display of the message "Parking brake
released".
Back-up switch-off
The indicator lamp flashes in response to a
Electric parking brake
manual request to apply or release the brake.
In automatic mode, this system applies the
In the event of a battery failure, the
parking brake when the engine is switched off
electric parking brake will not operate.
and releases it when the vehicle moves off.
As a safety measure, with a manual gearbox,
if the parking brake is not applied, immobilise
the vehicle by engaging a gear.
As a safety measure, with an automatic
gearbox, if the parking brake is not applied,
immobilise the vehicle by placing the supplied
chocks against one of the wheels.
Contact a PEUGEOT dealer or a qualified
If the electronic key is not detected or is no
workshop.
longer in the recognition zone, a message
At any time, with the engine running:
appears in the instrument panel when closing a
► To apply the parking brake, briefly pull the
door or trying to switch off the engine.
control.
102
Driving
Manual operation
► Select mode D, M or R.
6
► Release the brake pedal and depress the
Manual release
accelerator pedal.
With the ignition on or engine running:
If the brake does not release
► Press the brake pedal.
automatically, check that the front doors
► While maintaining pressure on the brake
are fully closed.
pedal, briefly push the control.
Before leaving the vehicle, check that the
If the brake pedal is not depressed, the
When stationary with the engine running,
parking brake is applied: the parking
parking brake is not released and a
do not depress the accelerator pedal
brake indicator lamps on the instrument panel
message is displayed.
unnecessarily. Risk of parking brake release.
and the control must be on fixed.
If the parking brake is not applied, there is an
audible signal and a message is displayed on
Manual application
Automatic application
opening the driver's door.
With the vehicle stationary:
With the vehicle stationary, the parking brake
► Briefly pull the control.
is applied automatically when the engine is
Never leave a child alone inside the
The control indicator lamp flashes to confirm the
switched off.
vehicle, as they could release the parking
application request.
It is not applied automatically if the
brake.
engine stalls or enters STOP mode with
Automatic operation
Stop & Start.
When the vehicle is parked: on a
Automatic release
steep slope, heavily loaded or during
In automatic mode, the parking brake
towing
First ensure that the engine is running and that
can be manually applied or released at
With a manual gearbox, turn the wheels
the driver's door is closed.
any time using the control.
toward the pavement and engage a gear.
The electric parking brake gradually releases
With an automatic gearbox, turn the wheels
automatically as the vehicle moves off.
toward the pavement and select mode P.
With a manual gearbox
Special cases
When towing, the vehicle is approved for
► Fully depress the clutch pedal and engage
parking on slopes of up to 12%.
first gear or reverse.
Immobilising the vehicle with the
► Depress the accelerator pedal and release
engine running
the clutch pedal.
To immobilise the vehicle with the engine
With an automatic gearbox
running, briefly pull the control.
► Depress the brake pedal.
103
Driving
Parking the vehicle with the brake
► Keep the control pushed in the release
one or both warning lamps on the instrument
released
direction for 10 to a maximum of 15 seconds.
panel, the vehicle’s stability is no longer ensured.
► Release the control.
► In this case, ensure the vehicle's stability by
In very cold conditions (ice), applying the
► Depress and hold the brake pedal.
successive and repeated "pull-release" actions
parking brake is not recommended.
► Pull the control in the application direction for
on the electric parking brake control until the
To immobilise the vehicle, engage a gear or
2 seconds.
vehicle comes to a complete stop.
place the chocks against one of the wheels.
This indicator lamp on the instrument
panel comes on to confirm deactivation of
Manual gearbox
With an automatic gearbox, mode P is
the automatic functions.
automatically selected when the ignition
► Release the control and the brake pedal.
is switched off. The wheels are blocked.
From this point onwards, only the manual
Engaging 5th or 6th gear
For more information on Free-wheeling, refer
functions, using the control, allow the parking
► Move the gear selector fully to the right to
to the corresponding section.
brake to be applied and released.
engage 5th or 6th gear.
► Follow this procedure again to reactivate
Failure to follow this instruction could
With an automatic gearbox, if you open
automatic operation (confirmed by the indicator
cause permanent damage to the gearbox
the driver's door while mode N is
lamp on the instrument panel going out).
(inadvertent engagement of 3rd or 4th gear).
engaged, an audible signal will sound and
Emergency braking
mode P will be engaged. The audible signal
stops when the driver's door is closed.
If depressing the brake pedal fails to provide
Engaging reverse gear
effective braking or in exceptional circumstances
(e.g. driver unwell, assisted driving), the vehicle
Deactivating automatic
can be braked by sustained pulling on the
operation
electric parking brake control. Braking continues
for as long as the control is kept pulled, and
In some situations, for example when it is
ceases when the control is released.
extremely cold or when towing (e.g. caravan,
The ABS and DSC systems stabilise the vehicle
breakdown), it may be necessary to deactivate
during emergency braking.
automatic operation of the system.
If emergency braking malfunctions, the message
► Start the engine.
► Use the control to apply the parking brake, if
"Parking brake fault" will be displayed on the
► Raise the ring under the knob and move the
it is released.
instrument panel.
gear selector to the left, then forwards.
If the ABS and DSC systems
► Take your foot fully off the brake pedal.
malfunction, indicated by lighting
104
Driving
Only engage reverse gear when the
Push selector
B. Driving in automatic mode with regenerative
6
vehicle is stationary with the engine at
braking function (Rechargeable hybrid)
idle.
Press this button to activate the regenerative
braking function.
As a safety precaution and to facilitate
The gearbox also manages braking when the
engine starting:
accelerator pedal is released.
► Always select neutral.
► In mode N, with your foot on the brake pedal,
► Press the clutch pedal.
push without passing the point of resistance:
• Forwards, mode R is selected.
• Backwards, mode D is selected.
Automatic gearbox
Release the selector fully after each push; it
will then return to its initial position.
With petrol / Diesel engines
P.
Auto Park
Special cases
Press this button to switch to Parking mode.
Automatic 8-speed gearbox with push selector.
To avoid mode N (quick change from D to R and
For parking the vehicle: the front wheels are
It also offers a manual mode with gear changes
back again):
blocked.
via control paddles located behind the steering
► In mode R, push backwards past the point of
R. Reverse
wheel.
resistance, mode D is selected.
N. Neutral
► In mode D, push forwards past the point of
To free-wheel and move the vehicle, with the
With Rechargeable hybrid
resistance, mode R is selected.
ignition off.
engines
► To return to mode N, push without passing
For more information on Free-wheeling, refer
Automatic 8-speed gearbox with push selector
to the corresponding section.
the point of resistance.
and regenerative braking function.
D. Driving in automatic mode
Steering-mounted controls
With the exception of the manual mode and
The gearbox manages gear changes
regenerative braking function, its operation is
according to the style of driving, the road
(Depending on equipment)
identical to that of other EAT8 gearboxes.
profile and the vehicle load.
In mode M or D, the steering-mounted control
M. Driving in manual mode (Petrol/Diesel)
paddles can be used to change gear manually.
Press this button to switch to manual mode.
They cannot be used to select neutral or to
The driver changes gear using the steering-
engage or disengage reverse gear.
mounted controls.
105
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст