Peugeot 308 (2022 year). Manual in english — page 4
Ease of use and comfort
The moving part A can be folded against the
High load retaining net (SW)
backrests of the rear seats.
Removal
► With the 2-position boot floor, first remove the
2 covers on each side of the housing.
Installation
► Compress the control B and lift the load
Hooked onto the special upper and lower fixings,
space cover on the right then on the left to
this removable net allows the use of the entire
remove it.
loading volume up to the roof:
Storage
- behind the front seats (row 1) when the rear
A recess located underneath the boot floor can
seats are folded,
be used to store the load space cover:
- behind the rear seats (row 2) when the load
- diagonally with the rigid boot floor.
space cover is removed.
- crosswise with the 2-position boot floor.
It protects the occupants in case of
► Position the left-hand end of the load space
sudden braking.
cover roller in its location 1 behind the rear left
seat.
► Compress the roller control B and put the
roller in place in its location 2 on the right.
► Release the control to secure the load space
cover.
► Unroll it until it clips on the boot pillars.
64
Ease of use and comfort
Behind the front seats
Behind the rear bench seat
To change the height:
3
► Lift and pull the floor towards you using its
central handle, then use the lateral stops to
move it.
► Push the floor all the way forwards to place it
in the desired position.
► Fold down the rear bench seat
► Remove the load space cover roller.
► Insert the ends of the bar, one after the other,
► Insert the ends of the bar, one after the other,
To keep it in the inclined position:
into the fixing points in the roof.
into the fixing points in the roof.
► From the high position, lift the floor towards
► Attach the net’s straps to the lower anchoring
► Attach the straps of the net to the lower rings,
the load space cover.
points, located on the fixings of the rear bench
located on each side trim of the boot.
► Engage it in the inclined position in the lateral
seat backrest.
► Pull on the straps to stretch the net.
stops to secure it in this position.
► Pull on the straps to stretch the net.
2-position boot floor (SW)
12 V accessory socket
(Depending on version)
► To connect a 12 V accessory (maximum
This 2-position floor allows the boot volume to
power: 120 W), lift the cover and plug in a
be optimised using the lateral stops located on
suitable adaptor.
the sides:
► Switch on the ignition.
- High position (100 kg max.): to obtain a flat
floor up to the front seats, when the rear seats
The connection of an electrical device
are folded down.
not approved by PEUGEOT, such as a
- Low position (150 kg max.): maximum boot
USB charger, may adversely affect the
volume.
operation of vehicle electrical systems,
causing faults such as poor radio reception or
On certain versions, the adjustable boot
interference with displays in the screens.
floor cannot be fitted in the low position.
65
Ease of use and comfort
Boot lamp
The load space cover can also be stored here
(SW).
It comes on automatically when the boot is
opened and goes off automatically when the
boot is closed.
The lighting time varies according to the
circumstances:
- When the ignition is off, approximately 10
minutes.
- In energy saving mode, approximately 30
seconds.
- With the engine running, unlimited.
Storage well
► Lift the rigid boot floor as far as possible or lift
the hinged boot carpet (depending on version) to
access the storage well.
► With the 2-position boot floor (SW), lift the
boot floor as far as possible or lift the cover at
the back of the boot to access one or other of the
storage wells.
The cover at the back of the boot is also
accessible from the second row seats if the
backrests of the rear bench seat are folded
down.
Depending on version, it includes:
- A hazard warning triangle.
- A temporary puncture repair kit with the tool
kit.
- A spare wheel with the tool kit.
- The traction battery charging cables
(Rechargeable hybrid).
66
Lighting and visibility
In "AUTO" and sidelamps mode, pull the lighting
only be used in fog or falling snow (rules may
Exterior lighting control
4
control stalk to switch the main beam headlamps
vary depending on country).
stalk
on directly ("headlamp flash").
Do not forget to switch off the foglamps when
they are no longer necessary.
Display
Main lighting
Illumination of the corresponding indicator
Switching off of the lamps when the
lamp on the instrument panel confirms that the
ignition is switched off
selected lighting is on.
When the ignition is switched off, all of the
A fault with a lamp is signalled by the
lamps turn off immediately, except for dipped
permanent illumination of this warning
beam headlamps if automatic guide-me-home
lamp, accompanied by the display of a message
lighting is activated.
and an audible signal.
Switching on the lamps after
Rear foglamps
switching off the ignition
Automatic illumination of lamps/daytime
They only work if the dipped or main
To reactivate the lighting control, rotate the
running lamps
beam headlamps are on.
ring to the "AUTO" position, then to the
Sidelamps only
desired position.
If the driver's door is opened, a temporary
Dipped or main beam headlamps
audible signal warns the driver that the lamps
are on.
They will go off automatically after a period
Headlamp dipping
of time that depends on the level of charge in
► Rotate the ring forwards/backwards to turn
the battery (entering energy economy mode).
them on/off.
When the lighting is switched off automatically
("AUTO" position) the foglamps and the dipped
In some weather conditions (e.g. low
beam headlamps remain on.
temperature or humidity), misting on the
internal surface of the glass of the headlamps
Switching on the foglamps is prohibited
and rear lamps is normal, and will disappear
in clear weather or in rain, both day and
after the lamps have been on for a few
night. In these situations, the power of their
minutes.
beams may dazzle other drivers. They must
► Pull the lighting control stalk to switch
between dipped and main beam headlamps.
67
Lighting and visibility
Never look too closely at the light beam
In daytime running lamps mode, the
Vehicle side marking by lighting the sidelamps
of LED technology lamps - risk of serious
diodes are brighter.
on the traffic side only.
eye injury!
► Within one minute after switching off the
ignition, operate the lighting control stalk
Direction indicators
upwards or downwards, depending on the side
of the traffic (e.g. when parking on the right, push
the lighting control stalk down to light up on the
left).
This is confirmed by an audible signal and the
lighting of the corresponding direction indicator
lamp on the instrument panel.
► To switch off the parking lamps, return the
Travelling abroad
lighting control stalk to the central position.
Vehicles equipped with manual
headlamp beam height adjustment:
► Left or right: lower or raise the lighting control
Headlamp beam height
If planning to use your vehicle in a country
stalk, beyond the point of resistance.
that drives on the other side of the road, the
adjustment
dipped beam headlamps must be adjusted to
If you keep the direction indicators on for
avoid dazzling oncoming drivers. Consult a
more than 20 seconds, the volume of the
Manual headlamp
PEUGEOT dealer or a qualified workshop.
audible signal will increase if the speed is
adjustment
above 50 mph (80 km/h).
Daytime running lamps/
Three flashes
Sidelamps
► Press briefly upwards or downwards, without
These LED lamps at the front of the vehicle light
going beyond the point of resistance; the
up automatically when the engine starts.
direction indicators will flash 3 times.
They perform the following functions:
The brightness of the daytime running lamps is
- Daytime running lamps (lighting control stalk
reduced when the direction indicators are on.
at position "AUTO" with adequate ambient light).
- Sidelamps (lighting control stalk at position
To avoid dazzling other road users, the height
Parking lamps
"AUTO" with low ambient light or "Sidelamps
of these headlamp beams must be adjusted
(Depending on version)
only" or "Dipped/main beam headlamps").
according to the load in the vehicle.
68
Lighting and visibility
0
(Initial setting)
is detected by the rain/sunshine sensor, the
The inner surface of the windscreen may
4
Driver only or driver + front passenger
sidelamps and dipped beam headlamps are
become misted up and affect the proper
1
5 people
switched on automatically, without any action on
operation of the rain/sunshine sensor.
2
5 people + load in the boot
the part of the driver. They may also come on if
In humid and cold weather, demist the
3
Driver only + load in the boot
rain is detected, at the same time as automatic
windscreen regularly.
4 5 6
Not used
operation of the windscreen wipers.
As soon as the brightness returns to a sufficient
level or after the windscreen wipers are switched
Guide-me-home and
Automatic Peugeot Matrix
off, the lamps are switched off automatically.
welcome lighting
LED Technology 2.0
Malfunction
headlamp adjustment
In the event of a malfunction of the rain/
Guide-me-home lighting
This system automatically adjusts the height of
sunshine sensor, the vehicle’s lamps
the headlamp beams according to the load in the
Automatic
come on and this warning lamp is displayed on
vehicle.
With the ring of the lighting control stalk in the
the instrument panel, accompanied by an
In the event of a malfunction, this warning
"AUTO” position and when the light is poor, the
audible signal and/or the display of a message.
lamp lights up on the instrument panel,
dipped beam headlamps come on automatically
Have it checked by a PEUGEOT dealer or a
accompanied by the display of a message and
when the ignition is switched off.
qualified workshop.
an audible signal.
You can activate/deactivate and adjust
The system places the headlamp beams in the
Do not cover the rain/sunshine sensor
the duration of the guide-me-home
lowest position.
located at the top centre of the
lighting in the Settings > Vehicle touch screen
Have it checked by a PEUGEOT dealer or a
windscreen behind the interior rear view
application.
qualified workshop.
mirror; the associated functions would no
Manual
longer be controlled.
Do not touch the Peugeot Matrix LED
Technology 2.0 headlamps - risk of
In fog or snow, the rain/sunshine sensor
electrocution!
may detect sufficient light. For this
reason, the lighting will not come on
automatically.
Automatic illumination of
lamps
With the lighting control stalk in the “AUTO”
position and if a low level of exterior brightness
69
Lighting and visibility
► With the ignition off, pull the lighting control
Do not allow snow to accumulate on the
Automatic lighting
stalk toward you ("headlamp flash") to activate/
bonnet or roof of the vehicle as this could
deactivate the function.
systems - General
obstruct the camera.
Manual guide-me-home lighting goes off
recommendations
automatically after a period of time.
The automatic lighting systems use a detection
Automatic headlamp
Welcome lighting
camera, located at the top of the windscreen.
dipping
When the vehicle is unlocked in low light
Operating limits
conditions and the "Automatic illumination of
The system may be disrupted or not work
For more information, refer to the
headlamps" function is activated, this system
correctly:
General recommendations for
automatically switches on:
- When visibility conditions are poor
automatic lighting systems.
- On the outside, sidelamps, dipped beam
(e.g. snowfall, heavy rain).
headlamps and door mirror spotlamps.
- If the windscreen is dirty, misted-up or
With the ring of the lighting control stalk in the
- Inside, courtesy lamps and footwell lighting.
masked (e.g. sticker) in front of the camera.
"AUTO" position and the function activated on
- If the vehicle is facing highly reflective signs
the touch screen, this system automatically
Door mirror spotlamps
or safety barrier reflectors.
switches between dipped and main beam
These spotlamps facilitate access to the vehicle
The system is not able to detect:
headlamps, according to lighting and traffic
by lighting the ground near the front doors.
- Road users that do not have their own
conditions, using a camera located at the top of
The spotlamps come on automatically:
lighting, such as pedestrians.
the windscreen.
- when the vehicle is unlocked.
- Vehicles with hidden lighting (e.g. travelling
- when a door is opened.
behind a safety barrier on the motorway).
- when a request to locate the vehicle is
- Vehicles at the top or bottom of a steep
received from the remote control.
slope, on winding roads, on crossroads.
They also come on with the welcome lighting
and guide-me-home lighting functions.
Maintenance
They go off automatically after 30 seconds.
Clean the windscreen regularly,
particularly the area in front of the camera.
The internal surface of the windscreen can
also become misted around the camera.
In humid and cold weather, demist the
windscreen regularly.
70
Lighting and visibility
The state of the system is stored when the
Pause
4
ignition is switched off.
If the situation requires a change of headlamp
When the system detects thick fog, it
beam, the driver can take over at any time.
temporarily deactivates the function.
► Switch the headlamps manually between
dipped and main beam to pause the function.
If the "AUTO" and "Dipped beam" indicator
Operation
lamps were on, the system changes to main
If the ambient light level is very low and traffic
beam.
conditions permit:
If the "AUTO" and "Main beam" indicator lamps
- The main beam headlamps
were on, the system changes to dipped beam.
come on automatically. These
► To reactivate the function, once again switch
indicator lamps light up on the instrument panel.
the headlamps manually between dipped and
If the ambient light level is sufficient and/or the
main beam.
traffic conditions do not allow the main beam
headlamps to be lit:
Malfunction
- The dipped beam headlamps
If a malfunction occurs with the system or
This system is a driving aid.
remain lit. These indicator lamps
the camera, this warning lamp lights up
The driver remains responsible for
light up on the instrument panel.
on the instrument panel, accompanied by an
the vehicle's lighting, its correct use in the
The function is deactivated if the foglamps
audible signal and a message.
prevailing light, visibility and traffic conditions,
are switched on or if the system detects poor
Have it checked by a PEUGEOT dealer or a
and for compliance with driving and vehicle
visibility conditions (e.g. fog, heavy rain,
qualified workshop.
regulations.
snowfall).
When the foglamps are switched off or when the
Peugeot Matrix LED
visibility conditions become favourable again, the
The system becomes operational when
function is automatically reactivated.
Technology 2.0
the vehicle exceeds 16 mph (25 km/h).
This indicator lamp goes out when the
When the speed falls below 9 mph (15 km/h),
function is deactivated.
For more information, refer to the
the function is no longer operational.
If the function is selected but the display
General recommendations for
on the instrument panel and the alerts are
automatic lighting systems.
Activation/Deactivation
not available, the indicator lamp comes on in
grey.
Available only on versions equipped with Full
It is configured in the Settings > Vehicle
LED headlamps with Matrix Beam function.
touch screen application.
71
Lighting and visibility
This system automatically adapts the main
signalled by the indicator lamp going off on
Followed vehicle
beam according to the driving conditions, so that
the instrument panel.
optimum illumination is maintained for the driver,
without causing a nuisance to other road users.
Travelling abroad
Vehicles equipped with the Peugeot
The driver remains responsible for the
Matrix LED Technology 2.0 function:
vehicle's lighting, its correct use in the
If planning to use your vehicle in a country
prevailing light, visibility and traffic conditions,
that drives on the other side of the road,
and for compliance with driving and vehicle
deactivate the function to avoid dazzling
regulations.
oncoming drivers.
When approaching a vehicle from behind, only
The system is active from 25 mph
those lamp segments directed at the followed
(40 km/h) and deactivates below 12 mph
Operation
vehicle go off, thereby creating a "tunnel" so as
(20 km/h).
not to dazzle its driver.
Using a camera, the system detects the driving
conditions (brightness, lights from oncoming or
Oncoming vehicle
followed vehicles, road turns) and adapts the
Activation/Deactivation
beams of the main headlamps accordingly.
► Place the ring of the lighting control stalk in
The modules that make up the main beams
the “AUTO” position.
switch on and off gradually, segment by
This indicator lamp comes on in the
segment, depending on the driving conditions
instrument panel.
detected.
It is configured in the Settings > Vehicle
Nominal main beam lighting is restored as soon
touch screen application.
as the vehicle is no longer detected by the
The state of the system is stored when the
system.
ignition is switched off.
When an oncoming vehicle approaches, only
When deactivated, the lighting system changes
those lamp segments directed at this vehicle
to "Automatic illumination of lamps" mode.
go off, thereby creating a "tunnel" during the
It is recommended that you deactivate
duration of the approach.
the function in foggy or snowy conditions
Entering an illuminated area
or in case of heavy mist.
At the entrance to an illuminated area (for
The function temporarily is deactivated when
example, a town), the lamp segments are
the system detects thick fog or when the
gradually switched off from the outside to the
foglamps are switched on manually. This is
72
Lighting and visibility
inside of the vehicle to switch to the dipped
Wiper control stalk
With AUTO wiping
4
beams.
Exiting an illuminated area
Before operating the wipers in wintry
conditions, clear any snow, ice or frost
The lamp segments gradually light up from the
from the windscreen and around the wiper
inside to the outside of the vehicle to restore the
arms and blades.
main beams.
Pause
Do not operate the wipers on a dry
Windscreen wipers
If the situation requires a change of headlamp
windscreen. In extremely hot or cold
► To select the wiping speed: raise or lower the
beam, the driver can take over at any time.
weather, check that the wiper blades are not
stalk to the desired position.
► Switch the dipped/main beam headlamps
stuck to the windscreen before operating the
Fast wiping (heavy rain)
manually to pause the function.
wipers.
The lighting system changes to "Automatic
Normal wiping (moderate rain)
illumination of lamps" mode.
After using an automatic car wash, you
► To reactivate the function, manually switch
may temporarily notice abnormal noises
Intermittent wipers
the dipped/main beam headlamps again.
and poorer wiping performance. You do not
need to replace the wiper blades.
or
Malfunction
Automatic wipers
If a malfunction occurs with the adaptive
With intermittent wipers
headlamp lighting or the camera, this
Switching off
warning lamp is displayed on the instrument
panel, accompanied by an audible signal and a
Manual
message.
Have it checked by a PEUGEOT dealer or a
After the ignition has been switched off,
qualified workshop.
the wipers may move slightly at the foot
Do not cover the rain/sunshine sensor
of the windscreen.
located at the top centre of the
windscreen behind the interior rear view
mirror; the associated functions would no
longer be controlled.
73
Lighting and visibility
In position 1 or 2, the wiping frequency is
With automatic air conditioning, any
reactivate wiping when the ignition is switched
automatically reduced when the speed of
action on the screenwash control results
on again (unless the ignition was off for less
the vehicle drops below 3 mph (5 km/h).
in temporary closure of the air intake to
than 1 minute).
When the speed is above 6 mph (10 km/h)
protect the passenger compartment from any
The first rotation of the ring to the screenwash
again, the wiping frequency returns to the
odour.
position triggers a single wipe. If the ring is
original frequency (fast or normal).
then left in the intermittent wiping position, the
To avoid damaging the wiper blades, do
rear wiper adopts a wiping speed dependent
not operate the screenwash if the
on that of the windscreen wipers and the
Single wipe
screenwash reservoir is empty.
speed of the vehicle.
If the wiper control stalk is:
Only operate the screenwash if there is no
► In the INT or AUTO position, pull the stalk
risk of the fluid freezing on the windscreen
briefly towards you then release it.
Reverse
and hindering visibility. During the winter
► In the 0 position, press briefly on the stalk
When reverse gear is engaged, the rear wiper
period, use "very cold climate" rated products.
then release it.
will come into operation automatically if the front
Never top up with water.
Pressing and holding triggers continuous wiping
windscreen wipers are operating.
at the normal wiping speed.
It is configured in the Settings > Vehicle
Rear wiper
touch screen application.
Windscreen wash
In the event of accumulation of snow or
► Pull the wiper control stalk towards you and
hard frost or if a bicycle carrier is fitted to
hold.
a towing system, deactivate the automatic
A final wiping cycle is performed when
rear wiper via theSettings > Vehicle touch
screenwashing ends.
screen application.
► Turn the ring to align the desired symbol with
The windscreen wash jets are
the marking.
incorporated into the tip of each wiper
Off
Rear screenwash
arm.
► Turn the ring as far as it will go and hold it in
An additional jet is installed below the
Intermittent wiping
position.
midpoint of the arm on the driver's side.
The screenwash and the wiper operate for as
Screenwash fluid is sprayed along the length
Screenwash-wipe
long as the ring remains turned.
of the wiper blade. This improves visibility and
A final wiping cycle is performed when screen
reduces screenwash fluid consumption.
washing ends.
If the ignition has been switched off with
the rear wiper active, operate the ring to
74
Lighting and visibility
An additional jet is fitted above the number plate
Automatic windscreen
Adjusting the sensitivity
4
to clean the reversing camera (depending on
wipers
version).
► The washing of the reversing camera is
In AUTO mode, the front wipers work
triggered by operating the rear screenwash.
automatically and adapt to the intensity of
precipitation depending on the sensitivity of the
Front intermittent wiping
sensor selected.
The first position (upper) corresponds to the
The rainfall detection function uses a rain/
In Intermittent mode, the driver can adjust the
lowest sensitivity of the sensor.
sunshine sensor located at the top centre of the
wiping frequency by turning the ring to one of the
The last position (lower) corresponds to the
windscreen, behind the rear view mirror.
5 available positions.
highest sensitivity of the sensor.
In certain weather conditions (e.g. fog,
The higher the sensitivity, the faster the system
frost, snow, projections on salty roads),
reacts and increases the wiping frequency.
the driver may have to return to manual
A rotation of the ring from a higher position to a
wiping.
lower position triggers a confirmation wiping.
After the ignition has been switched off
The first (upper) position corresponds to the
Switching on/off
for more than 1 minute with the wiper
longest time interval between 2 wipes for light
control stalk in the AUTO position, when the
rain.
To switch on:
ignition is switched on again:
The last (lower) position corresponds to the
► Put the wiper control stalk in the AUTO
- the system works, depending on the
shortest time interval between 2 wipes for heavy
position.
volume of rain detected, as soon as the
rain.
► Turn the ring to adjust the sensitivity of the
vehicle exceeds 6 mph (10 km/h), if the
A rotation of the ring from a higher position to a
sensor.
outside temperature is below +3°C.
lower position triggers a confirmation wiping.
A wiping cycle, accompanied by the display of
- the system works immediately, depending
a message, confirms that the request has been
After the ignition has been switched off
on the volume of rain detected, if the outside
taken into account.
for more than 1 minute with the wiper
temperature is above +3°C.
► To switch off, put the wiper control stalk in
control stalk in the INT, 1 or 2 position, when
another position or in the 0 position.
the ignition is switched on again:
Do not cover the rain/sunshine sensor.
- the system works as soon as the vehicle
When using an automatic car wash,
exceeds 6 mph (10 km/h), if the outside
switch off the automatic wipers and the
temperature is below +3°C.
ignition.
- the system works immediately, if the
outside temperature is above +3°C.
75
Lighting and visibility
In winter, wait until the windscreen is
Before removing a windscreen wiper blade
Changing a wiper blade
completely clear of ice before activating the
automatic wipers.
Removing/Refitting at the front
Malfunction
If a fault occurs with the automatic wipers, the
wipers operate in intermittent mode.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
Operating the wiper control stalk immediately
after switching off the ignition will place the wiper
Special position of the
blades in a vertical position.
windscreen wipers
► Proceed with the desired operation or the
replacement of the wiper blades.
This maintenance position is used while cleaning
or replacing the wiper blades. It can also be
After refitting a windscreen wiper blade
► Carry out these wiper blade replacement
useful, in wintry weather (ice, snow), to release
► To return the wiper blades to their initial
operations from the driver's side.
the wiper blades from the windscreen.
position after the operation, switch on the ignition
► Starting with the wiper blade farthest from
and operate the wiper control stalk.
To maintain the effectiveness of the flat
you, hold each arm by the rigid section and raise
wiper blades, it is advisable to:
it as far as possible.
- handle them with care.
Take care not to hold the arms at the jet
- clean them regularly using soapy water.
locations.
- avoid using them to hold cardboard on the
Do not touch the wiper blades - risk of
windscreen.
irreparable deformation.
- replace them at the first signs of wear.
Do not release them while moving them. Risk
of damaging the windscreen!
► Clean the windscreen using screenwash
fluid.
Do not apply "Rain X" type water-
repellent products.
76
Lighting and visibility
► Unclip the worn wiper blade closest to you
Take care not to use an incorrect position
4
and remove it.
during fitting - risk of damage!
► Install the new wiper blade and clip it to the
arm.
► Repeat the procedure for the other wiper
blade.
► Starting with the wiper blade closest to you,
once again hold each arm by the rigid section,
then guide it carefully onto the windscreen.
Removing/refitting at the rear
► Hold the arm by the rigid section and raise it
as far as possible.
► Clean the rear screen using screenwash
fluid.
► Identify the position of the arm on which the
wiper blade is attached.
► Unclip the worn wiper blade by pulling it
towards the rear screen and remove it.
► Install the new wiper blade in the same
position of the arm and clip it into position.
► Once again hold the arm by the rigid section,
then guide it carefully onto the rear screen.
77
Safety
be held responsible if this advice is not
General safety
Hazard warning lamps
followed.
recommendations
- Any modification or adaptation not intended
or authorised by PEUGEOT or carried out
Do not remove the labels attached in
without meeting the technical requirements
different places on your vehicle. They
defined by the Manufacturer will result in the
include safety warnings as well as
suspension of the commercial warranty.
identification information for the vehicle.
Installation of accessory radio
Depending on country regulations,
► Pressing this button causes all the direction
communication transmitters
certain safety equipment may be
indicators to flash.
Before installing a radio communication
mandatory: high visibility safety vests,
They can work with the ignition switched off.
transmitter with an external aerial, you must
warning triangles, breathalysers, spare bulbs,
without fail contact a PEUGEOT dealer for
spare fuses, fire extinguisher, first aid kit, mud
Automatic operation of
the specification of transmitters which can
flaps at the rear of the vehicle, etc.
be fitted (frequency, maximum power, aerial
hazard warning lamps
position, specific installation requirements),
When braking in an emergency, depending on
Installing electrical accessories:
in line with the Vehicle Electromagnetic
the rate of deceleration, the hazard warning
- The fitting of electrical equipment or
Compatibility Directive (2004/104/EC).
lamps come on automatically. They switch off
accessories not approved by PEUGEOT may
automatically when you next accelerate.
cause excessive current consumption and
Declarations of conformity for radio
They can be switched off by pressing the button.
faults and failures with the electrical system
equipment
of your vehicle. Contact a PEUGEOT dealer
The relevant certificates are available on the
for information on the range of approved
accessories.
website.
- As a safety measure, access to the
diagnostic socket, used for the vehicle's
electronic systems, is reserved strictly for
PEUGEOT dealers or qualified workshops,
equipped with the special tools required (risk
of malfunctions of the vehicle's electronic
systems that could cause breakdowns or
serious accidents). The Manufacturer cannot
78
Safety
Have it checked by a PEUGEOT dealer or a
According to the country of sale, the eCall (SOS)
Horn
5
qualified workshop.
system corresponds to the systems PE112,
ERAGLONASS, 999, etc.
The eCall (SOS) system is activated by default.
Emergency or assistance
► To make an emergency call manually, press
call
button 1 for more than 2 seconds.
The lit indicator lamp and a voice message
confirm that the call has been made to the
emergency services*.
The eCall (SOS) system immediately locates
your vehicle and puts you in contact with the
appropriate emergency services**.
► Pressing again immediately cancels the
► Press the central part of the steering wheel.
request.
The indicator lamp flashes while the vehicle
Pedestrian horn
1. eCall (SOS)
data is being sent, and then remains lit when
2. ASSISTANCE
communication is established.
(Rechargeable hybrid)
In the event that a serious accident is
This system alerts pedestrians that the vehicle
eCall (SOS)
detected by the sensors built into the
is approaching, when driving in Electric mode
(100% electric driving).
Your vehicle may be fitted with the eCall (SOS)
vehicle, such as the airbag control unit, an
The pedestrian horn operates once the vehicle
system either as standard or as an option.
emergency call is made automatically.
is moving and at speeds of up to 19 mph
The eCall (SOS) system provides direct contact
(30 km/h), in forward or reverse gear.
to the emergency services and is fully built
The eCall (SOS) system is a public
This function cannot be deactivated.
into the vehicle. This contact is made either
service and is free-of-charge.
automatically via the sensors built into the
Malfunction
vehicle, or by pressing button 1.
In the event of a malfunction, this warning
lamp lights up on the instrument panel.
* In accordance with the general conditions of use of the service, available from dealers and subject to technological and technical limitations.
** Depending on the geographic coverage provided by the "eCall (SOS)" and "ASSISTANCE" systems.
The list of countries covered and the telematic services provided is available from dealers or on the website for your country.
79
Safety
Operation of the system
Council, and in particular, seeks to protect
the vehicle’s three most recent locations,
- Upon switching on the ignition, the indicator
the vital interests of the data subject, in
necessary for the normal functioning of the
lamp lights up for a few seconds and then goes
accordance with Article 6 (1) d) GDPR.
system, are stored.
out: the system is operating correctly.
The processing of personal data is strictly
When an emergency call is triggered, the data
- The indicator lamp flashes red: emergency
limited to the purpose of handling the eCall
log is stored for no more than 13 hours.
battery is flat. This will be recharged after a few
(SOS) function used with the “112” single
minutes' driving.
European emergency call number.
Access to data
- The indicator lamp is fixed red: system
The eCall (SOS) function is only able to
You have the right of access to data and
malfunction. The emergency and assistance call
collect and process the following data
as appropriate to request the rectification,
services may not work.
relating to the vehicle: vehicle identification
erasure or restriction of processing of any
- If the indicator lamp does not light up when
number, vehicle type (passenger vehicle or
personal data not processed in accordance
the ignition is turned on, this is also a system
light commercial vehicle), fuel type or power
with the provisions of GDPR. Third parties
malfunction.
source, three most recent locations and
to which data has been disclosed shall
If the problem persists, contact a qualified
direction of travel, number of passengers
be notified of any rectification, erasure or
workshop as soon as possible.
and a timestamped log file of the automatic
restriction carried out in compliance with
activation of the system and its timestamp.
GDPR, unless it proves impossible or
The malfunction of the system does not
The recipients of the processed data are the
involves a disproportionate effort.
prevent the vehicle from driving.
emergency call handling centres designated
You also have the right to lodge a complaint
by the relevant national authorities in the
with the respective data protection
When an onboard system update is
territory in which they are located, enabling
supervisory authority.
being performed, the eCall (SOS)
priority routing and handling of calls to the
If you want to claim your above-mentioned
function is not available.
“112” emergency number.
rights please contact us per email at:
privacyrights@stellantis.com.
Data processing
Data storage
For more information regarding our contact
All processing of personal data by
Data contained in the system’s memory
details please take a look at our Privacy &
the eCall (SOS) function complies with
is not accessible from outside the system until
Cookies Policy on the brand's website.
the framework for protection of personal
a call is made. The system is not traceable
information established by Regulation
and is not continuously monitored in its
2016/679 (General Data Protection
normal operating mode.
Regulation - GDPR) and Directive 2002/58/
The data in the system's internal memory is
EC of the European Parliament and the
automatically and continuously erased. Only
80
Safety
ASSISTANCE
During an update to the vehicle's
Anti-lock braking system
5
on-board telematics system, the
► If the vehicle breaks down, press button 2
(ABS)/Electronic brake force
ASSISTANCE system will be unavailable.
for more than 2 seconds to request assistance
distribution (EBFD)
(confirmed by a voice message*).
► Pressing again immediately cancels the
If you benefit from the Peugeot Connect
These systems enhance the vehicle’s stability
request.
Packs offer with the SOS and Assistance
and handling during braking, and enable greater
Pack included, there are additional services
control while cornering, particularly on poor or
Privacy mode allows you to manage the
available to you in your personal space, via
slippery road surfaces.
level of sharing (data and/or location)
the website for your country.
ABS prevents wheel locking in the event of
between your vehicle and PEUGEOT.
For information about the SOS and
emergency braking.
It can be configured in the Settings touch
Assistance Pack, please refer to the general
Electronic brake force distribution (EBFD)
screen application.
conditions for these services.
manages overall braking pressure on each
individual wheel.
If you purchased your vehicle outside the
► When braking in an emergency, depress
PEUGEOT dealer network, you are
the pedal very firmly and maintain this
Electronic stability control
invited to have a dealer check the
pressure.
configuration of these services and, if desired,
(ESC)
Normal operation of the ABS may make
modify it as required. In a multilingual country,
The electronic stability control programme
itself felt by slight vibrations of the brake
services can be configured to use the official
includes the following systems:
pedal.
national language of your choice.
- Anti-lock braking system (ABS) and Electronic
brake force distribution (EBFD).
The fixed illumination of this warning lamp
For technical reasons and in particular to
- Emergency braking assistance (EBA).
signals that there is a fault with the ABS.
improve the quality of telematics services
- Post Collision Safety Brake (PCSB).
The vehicle retains conventional braking. Drive
provided to customers, the Manufacturer
- Anti-slip regulation (ASR).
carefully at a moderate speed.
reserves the right to carry out updates to the
- Dynamic stability control (DSC).
Have it checked by a PEUGEOT dealer or a
vehicle's on-board telematics system at any
– Trailer stability assist (TSA).
qualified workshop.
time.
This warning lamp, when lit together with
the STOP and ABS warning lamps,
* Depending on the geographic coverage of the "eCall (SOS)" and "ASSISTANCE" systems and the official national language chosen by the owner of the
vehicle.
The list of countries covered and the telematic services provided is available from dealers or on the website for your country.
81
Safety
accompanied by a message and an audible
The system is not operational if the capability
Anti-slip regulation (ASR)/
signal, indicates an EBFD malfunction.
of the vehicle is to trigger and execute the
Dynamic stability control
You must stop the vehicle.
automatic post collision braking is not available,
Stop as soon as it is safe to do so and switch off
as it can occur in destructive accidents or in
(DSC)
the ignition.
other specific accident scenarios.
Anti-slip regulation (or traction control) optimises
Contact a PEUGEOT dealer or a qualified
It is possible to override the automatic braking by
traction by using engine braking and by applying
workshop.
pressing the brake pedal or accelerator pedal.
the brakes on the driving wheels to avoid one
or more wheels spinning. It also enhances the
When changing wheels (tyres and rims),
Operating conditions
vehicle's directional stability.
ensure that these are approved for your
The system operates, if the following conditions
If there is a difference between the vehicle’s
vehicle.
are met:
trajectory and the path desired by the driver, the
- Airbags or pyrotechnic seat belt pretensioners
dynamic stability control system automatically
After an impact
have been deployed by the collision.
uses engine braking and the brakes on one or
Have it checked by a PEUGEOT dealer
- Braking systems and electric functions remain
more wheels to return the vehicle to the desired
or a qualified workshop.
continuously operational during and after
path, within the limits of the laws of physics.
collision.
These systems are activated automatically every
Emergency braking
- Driver has not depressed the brake or
time the vehicle is started.
accelerator pedal.
These systems are activated in the event
assistance (EBA)
of a problem with grip or trajectory
This system reduces the emergency stopping
Malfunction
(confirmed by this warning lamp flashing on the
distance, by optimising the braking pressure.
In the event of a
instrument panel).
It is triggered in relation to the speed at which
malfunction, one of these
the brake pedal is depressed. The effect of this
warning lamps will come on fixed on the
Deactivation/Reactivation
is a reduction in the resistance of the pedal and
instrument panel, accompanied by the Service
In exceptional conditions (e.g. moving a vehicle
an increase in braking efficiency.
warning lamp, the display of a message and an
that is bogged down in mud, stuck in snow, on
audible signal.
loose soil), it may prove useful to deactivate the
Post Collision Safety Brake
Have it checked by a PEUGEOT dealer or a
DSC/ASR systems, so that the wheels can move
(APCB)
qualified workshop.
freely and regain grip.
If an accident is detected, the vehicle initiates
Reactivate the system as soon as the level of
automatic post collision braking. The goal of this
grip permits.
system is to reduce the risk of further collisions if
On GT Pack versions
the driver does not react.
82
Safety
Malfunction
on Identification markings, refer to the
5
In the event of a malfunction, this warning
corresponding section.
lamp lights up on the instrument panel,
accompanied by the display of a message and
Trailer stability assist (TSA)
an audible signal.
When towing, this system reduces the risk of the
Have it checked by a PEUGEOT dealer or a
vehicle or trailer snaking.
qualified workshop.
ASR/DSC
Operation
These systems enhance safety during
The system is activated automatically when the
► Press this button to deactivate/reactivate the
normal driving, but should not encourage
ignition is switched on.
DSC/ASR system (confirmed by the indicator
the driver to take extra risks or drive at high
The electronic stability control system (ESC)
lamp coming on/going out).
speed.
must not have any faults.
Deactivation/reactivation of the DSC/ASR
It is in conditions of reduced grip (rain, snow,
The vehicle speed must be between 37 and 99
system is indicated by this indicator lamp
ice) that the risk of loss of grip increases. It
mph (60 and 160 km/h).
on the instrument panel coming on/going out and
is therefore important for your safety to keep
If the system detects that the trailer is
the display of a message.
these systems activated in all conditions, and
snaking, it applies the brakes to stabilise
The DCS/ASR system is automatically
particularly in difficult conditions.
the trailer and reduces engine power, if
reactivated every time the ignition is switched off.
Correct operation of these systems depends
necessary, to slow the vehicle (indicated by the
On non-GT Pack versions
on compliance with the manufacturer's
flashing of this warning lamp on the instrument
The ASR system is deactivated/
recommendations relating to the wheels
panel and the brake lamps coming on).
reactivated in the ADAS touch screen
(tyres and rims), braking and electronic
For information on weights and towed loads,
application.
components, as well as the assembly and
refer to the Engine technical data and towed
Deactivation/reactivation of the ASR
repair procedures provided by PEUGEOT
loads section or your vehicle’s registration
system is indicated by this indicator lamp
dealers.
certificate.
on the instrument panel coming on/going out and
In order to ensure that these systems remain
To ensure safe driving with a Towing device,
the display of a message.
effective in wintry conditions, the use of snow
refer to the corresponding section.
The ASR system is automatically reactivated
or all-season tyres is recommended. All four
every time the ignition is switched off or at
wheels must be fitted with tyres approved for
Malfunction
speeds over 31 mph (50 km/h)
your vehicle.
If a fault occurs, this warning lamp lights
Reactivation is manual below 31 mph (50 km/h).
All tyre specifications are listed on the
up on the instrument panel, accompanied
tyre/paint label. For more information
by a message and an audible signal.
83
Safety
To continue towing a trailer, reduce speed and
over. It can be released by pulling the strap firmly
Front seat belts
drive carefully!
and then releasing it so that it reels in slightly.
The front seat belts are fitted with a pyrotechnic
Have it checked by a PEUGEOT dealer or a
Pyrotechnic pretensioning
pretensioning system and a progressive force
qualified workshop.
This system improves safety in the event of a
limiting system.
frontal or side impact.
The trailer stability control system
Depending on the severity of the impact, the
provides an extra safety feature under
Rear seat belts
pyrotechnic pretensioning system instantly
normal driving conditions, when following the
tightens the seat belts against the body of the
recommendations for use of trailers and
occupants.
current legislation in force in your country. It
The pyrotechnic pretensioning seat belts are
must not encourage the driver to take extra
enabled when the ignition is on.
risks, such as using a trailer in unsuitable
Progressive force limiting system
conditions of operation (e.g. excessive load,
This system reduces the pressure of the seat
exceeded nose weight, worn or under-inflated
belt on the chest of the occupant, taking their
tyres, faulty braking system) or driving at
stature into account, thus improving their
excessive speed.
protection.
In certain cases, the system may not detect
trailer snaking, particularly with a light trailer.
In the event of an impact
When driving on slippery or poor surfaces, the
Depending on the nature and
Each of the rear seats has a three-point seat belt
system may not be able to prevent sudden
seriousness of the impacts, the pyrotechnic
with inertia reel.
trailer snaking.
device may trigger before and independently
The outer seats are fitted with a pyrotechnic
of airbag deployment. Deployment of the
pretensioning and force limiting system.
pretensioners is accompanied by a slight
discharge of harmless smoke and a noise,
Fastening
Seat belts
due to the activation of the pyrotechnic
► Pull the strap, then insert the tongue into the
Inertia reel
cartridge incorporated in the system.
buckle.
The seat belts are equipped with an inertia
In all cases, the airbag warning lamp comes
► Check that the seat belt is fastened correctly
reel which allows the strap length to adjust
on.
by pulling on the strap.
automatically to the shape of the user. The seat
Following an impact, have the seat belt
belt returns to its storage automatically when it
system checked, and if necessary replaced,
Unfastening
is not used.
by a PEUGEOT dealer or a qualified
► Press the red button on the buckle.
The inertia reels are fitted with a device which
workshop.
► Guide the seat belt as it is reeled in.
automatically locks the strap in the event of a
collision, emergency braking or if the vehicle rolls
84
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст