Renault Arkana (2021 year). Manual in english — page 8
LANE DEPARTURE WARNING (5/5)
This function is an additional driving aid. This function is not under any circumstances intended to replace the due care
and attention of the driver, who should at all times be in control of the vehicle.
System servicing/repairs
- In the event of an impact, the camera alignment may be changed, and its operation may consequently be affected. Deactivate
the function, then consult an authorised dealer.
- Any work in the area where the camera is located (repairs, replacements, windscreen modifications etc.) must be carried
out by a qualified professional.
Only an authorised dealer is qualified to service the system.
In the event of system disturbance
Some conditions can disturb or damage the operation of the system, such as:
- windscreen obscured (by dirt, ice, snow, condensation etc.);
- a complex environment (tunnel etc.);
- poor weather conditions (snow, rain, hail, black ice etc.) ;
- poor visibility (night, fog etc.);
- the road markings are irregular or difficult to distinguish (e.g. partially erased, excessive spacing, distorted road surface) ;
- being dazzled (glaring sun, lights of vehicles travelling in the opposite direction etc.);
- the road is narrow, winding or undulating (tight bends etc.);
- closely following a vehicle travelling in the same lane.
Risk of false alarms or absence of warnings
2.41
LANE KEEPING ASSIST (1/6)
Note: make sure the windscreen is not
1
obscured (dirt, mud, snow, condensa-
tion etc.).
Using information from the 1 camera,
This function is an addi-
the function triggers corrective action
tional driving aid and the
on the vehicle steering system when
driver is responsible for
a continuous or broken line is crossed
steering wheel operation.
or when approaching the roadside (di-
This system is not a substitute for
vider, barrier, pavement, embankment,
the driver and the driver must drive
etc.) without the direction indicator
with his hands on the streering
lights being activated.
wheel when driving.
Always be careful when driving, as
the system may not be unexpect-
edly deactivated or operated, or
may operate unecessarily depend-
ing on the road conditions and at-
tention circumstances.
You can retake control of the ve-
hicle at any time by operating the
steering wheel.
2.42
LANE KEEPING ASSIST (2/6)
To disable the function, press the 2
switch as many times as required to
select “Lane Keeping deactivated” on
the instrument panel.
Warning light
goes out on the in-
strument panel.
Note: deactivating the “Lane Keeping
2
Assist” function causes deactivation of
the “Lane Departure Warning” function.
Activation/deactivation
To activate the function, press the 2
switch as many times as required to
select “Lane Keeping Assist” on the in-
strument panel.
The “Lane Keeping activated” message
and “
” warning light are displayed
on the instrument panel.
When Lane Keeping Assist is activated,
the “Lane Departure Warning” function
is automatically activated. ➥ 2.37
Each time the vehicle is started,
the function continues the mode
saved the last time the engine was
stopped.
2.43
LANE KEEPING ASSIST (3/6)
The function operates if the vehicle
Special case
breaches a line or if the vehicle ap-
When using the system:
proaches the roadside (divider, barrier,
-
If the system can no longer detect
pavement, embankment, etc.) without
any action by the driver on the steer-
the direction indicator lights being ac-
tivated.
ing wheel, the
warning light
appears in orange on the instrument
In these cases:
3
panel, accompanied by the message
- the function triggers an action on the
“Keep hands on steering wheel” and
vehicle’s steering system to correct
an audible warning.
the vehicle trajectory;
-
if the system is active for too long,
- the 3 indicator on the side of the
an audible warning is emitted and
breached line turns to yellow on the
the indicator 3 on the side of the line
instrument panel.
concerned flashes until the driver
takes control.
Note: on bends, the function allows for
slightly cutting the bend.
Operation
When the function is activated, the
If the corrective action on the steer-
Please note that the system
warning light and the left and
ing system is not sufficient, the
warning may appear late
right lines 3 are displayed in grey on the
warning light and 3 indicator on the side
according to road condi-
instrument panel.
of the breached line turn to red on the
tions when driver’s hands
instrument panel, accompanied by a vi-
are off the steering wheel.
The function is set to operate when
bration on the steering wheel.
the vehicle speed is between approxi-
Always have your hands on the
mately 43 mph (70 km/h) and 112 mph
steering wheel when driving.
(180 km/h) and if the
warning
The system may warn driver that
light and 3 correction indicators are col-
driver is not holding the steering
oured white.
wheel when the driver operates
steering wheel excessively or holds
on the steering wheel softly.
You can interrupt the trajectory cor-
rection at any time by moving the
steering wheel.
2.44
LANE KEEPING ASSIST (4/6)
Temporarily not available
Conditions for non-activation
– very fast lane departure;
of the system
4
The system cannot be activated when:
- driving continuously on a line;
- four seconds approximately after
- reverse gear is engaged;
changing lanes;
- the field of vision of the camera is ob-
- tight bends;
structed;
- impaired visibility;
- the û
warning light is displayed.
- activation of one of the direction indi-
The
warning light and the left/
cator lights;
right line warning lights are displayed in
- strong acceleration;
grey on the instrument panel.
– emergency braking;
- ...
Adjustment
-
“Warning”: adjust the line detection
If the function is unavailable, the
Vehicles fitted with a multimedia
sensitivity level. To do this, select:
warning light and the left/right correc-
screen.
- “Late”: line detected when cross-
tion warning lights 3 appear in grey on
To access the multimedia screen func-
ing;
the instrument panel.
tion settings 4, refer to the multimedia
- “Standard”: line detected on ap-
instructions:
proach;
- “Vibration”: adjust steering wheel
- “Early”: line detected nearby.
vibration for the
“Lane Departure
Warning” function;
Please refer to the multimedia instruc-
tions for further information.
2.45
LANE KEEPING ASSIST (5/6)
- press the 6 or 7 control repeatedly to
Operating faults
reach the “DRIVING ASSIST” menu.
When the system detects an operating
Press the switch 8 OK;
fault, the
warning light lights up
– scroll repeatedly by pressing 6 or 7
on the instrument panel, with the mes-
to reach the “Lane Keeping sen-
sage “Front camera to check”.
sitivity” menu. Press the switch 8
Consult an approved dealer.
OK ;
- scroll repeatedly pressing control 6
6
or 7 to adjust the setting. Press the 8
5
OK button.
8
7
Adjustments (continued)
Vehicles not fitted with a multimedia
screen
- With the vehicle stopped, press the
switch 5 as many times as required
to reach the “Vehicle” tab;
- press the 6 or 7 control repeatedly to
reach the “Settings” menu. Press the
switch 8 OK;
2.46
LANE KEEPING ASSIST (6/6)
This function is an additional driving aid. This function is not under any circumstances intended to replace the due care
and attention of the driver, who should at all times be in control of the vehicle.
System servicing/repairs
- In the event of an impact, the camera alignment may be changed, and its operation may consequently be affected. Deactivate
the function and consult an authorised dealer.
- Any work in the area where the camera is located (repairs, replacements, windscreen modifications etc.) must be carried
out by a qualified professional.
Only an authorised dealer is qualified to service the system.
In the event of system disturbance
Some conditions can disturb or damage the operation of the system, such as:
- windscreen obscured (by dirt, ice, snow, condensation etc.);
- a complex environment (tunnel etc.);
- poor weather conditions (snow, rain, hail, black ice etc.) ;
- poor visibility (night, fog etc.);
- the road markings are irregular or difficult to distinguish (e.g. partially erased, excessive spacing, distorted road surface) ;
- being dazzled (glaring sun, lights of vehicles travelling in the opposite direction etc.);
- the road is narrow, winding or undulating (tight bends etc.);
- closely following a vehicle travelling in the same lane.
In this case, the “Lane Keeping Assist” may react incorrectly or not at all.
Risk of unwanted, incorrect correction or no correction of trajectory.
Deactivating the function
You must disable the function if:
- the area of the camera has been damaged (on the windscreen side or the interior rear-view mirror side);
- the road is slippery (snow, black ice, aquaplaning, gravel etc.) ;
- poor visibility (night, fog etc.);
- the windscreen is cracked or distorted (do not carry out windscreen repairs in this area; have it changed by an Authorised
Dealer);
- the vehicle is towing a trailer or a caravan;
- the vehicle is entering an area with several surface markings (an area with road works etc.).
2.47
BLIND SPOT WARNING (1/7)
A
B
C
A
B
Using information from the sensors in-
Special feature
stalled on each side of the rear bumper
Ensure that the C area around the
(area C), the function warns the driver:
radars on each side of the rear bumper
are not obstructed (by dirt, mud, snow
- when another vehicle appears in the
etc.)
detection area A;
If a radar is obscured, the message
and/or
“Side radars no visibility” will appear on
- when there is a risk of collision with
the instrument panel. Clean the area
a vehicle that is in area B, driving
where the sensors are located.
faster than you.
This function is an addi-
tional driving aid. This func-
The function warns you when the ve-
tion is not under any cir-
hicle is travelling at a speed above ap-
cumstances intended to
proximately 9 mph (15 km/h).
replace the due care and attention
of the driver, who should at all times
be in control of the vehicle.
2.48
BLIND SPOT WARNING (2/7)
- press the switch 5 OK again to acti-
vate or deactivate the function:
1
=
function activated
<
function deactivated
3
2
5
4
Activation/deactivation
- press the 3 or 4 control repeatedly to
reach the “Settings” menu. Press the
Vehicles fitted with a multimedia
switch 5 OK;
screen 1
- press the 3 or 4 control repeatedly to
To activate or deactivate the function,
reach the “DRIVING ASSIST” menu.
refer to the multimedia instructions.
Press the switch 5 OK;
Select “ON” or “OFF”.
- press the 3 or 4 control repeatedly to
reach the “Blind spot alert” menu and
Vehicles not fitted with a multimedia
press the 5 OK switch;
screen
- With the vehicle stopped, press the 2
switch as many times as required to
The system’s detection range oper-
reach the “Vehicle” tab;
ates according to a standard lane
width. When driving in a narrow
lane, the function can warn you
when a vehicle is detected beyond
the adjacent lane.
2.49
BLIND SPOT WARNING (3/7)
6
A
B
7
A
B
Indicator 6
Operation
An indicator light 6 is located on each
The function warns you when the speed
rear view mirror 7.
of your vehicle is over 9 mph (15 km/h):
- when another vehicle is in the blind
Note: clean the rear view mirrors 7 reg-
spot area A and travelling in the
ularly so that the indicators 6 can be
same direction as your vehicle;
seen.
- when a vehicle approaches quickly
from the rear in an adjacent lane
within the range of detection area B.
If you overtake another vehicle, the 6
indicator will only come on if that vehi-
cle remains for a long enough period in
your vehicle’s blind spot A.
The function does not notify the
driver if the other vehicles are not
moving.
2.50
BLIND SPOT WARNING (4/7)
Display E
Conditions for non-function
6
Direction indicator activated, the 6
- When driving on a road with tight
warning light flashes when the func-
bends;
tion detects a vehicle in the blind spot
- in reverse.
warning area and/or a vehicle is rapidly
D
approaching from the rear on the side
If the vehicle is equipped with a towbar
towards which you will turn the wheel.
recognised by the system, the “Trailer:
If you cancel the direction indicator, the
blind spot alert off” message displayed
function will return to the initial warning
on the instrument panel informs you
(display D).
that the function is not operational. For
information on the range of equipment
E
adapted to your vehicle, we advise you
to consult an approved Dealer.
Display D
First warning: direction indicator not
activated, the 6 warning light indicates
that a vehicle is detected in the blind
spot area and/or that a vehicle is rap-
idly approaching from the rear in an ad-
jacent lane.
When the engine is started, the
system adopts the last status saved
before the ignition was switched off
(refer to the previous pages).
2.51
BLIND SPOT WARNING (5/7)
Operating faults
If the system detects a fault, the mes-
sage “Check Side radars” is displayed
on the instrument panel. Consult an ap-
proved dealer.
-The system’s detection
range operates according
to a standard lane width. If
you are driving in wide traf-
fic lanes, the system might not
be able to detect a vehicle in the
blind spot.
- The system might be disrupted
momentarily if it is exposed to
strong electromagnetic waves
(as beneath high-tension power
lines) or to very poor weather
conditions
(heavy rain, snow
etc.). Remain aware of driving
conditions.
Due to the presence of sensors
There is a risk of accidents.
behind the bumper, it is advisable to
entrust any operation on the bumper
(repair, replacement, paintwork,
etc.) to a qualified professional.
2.52
BLIND SPOT WARNING (6/7)
This function is an additional driving aid. This function is not under any circumstances intended to replace the due care
and attention of the driver, who should at all times be in control of the vehicle.
The driver should always adapt their speed to the traffic conditions, regardless of the system indications.
The system should under no circumstances be taken to be an obstacle detector or an anti-collision system.
System servicing/repairs
- In the event of an impact, radar alignment may be changed, and its operation will consequently be affected. Deactivate the
function and consult an authorised dealer.
- Any work in the area where the radars are located (repairs, replacements, etc.) must be carried out by a qualified profes-
sional.
Only an authorised dealer is qualified to service the system.
System disturbance
Some conditions can disturb or damage the operation of the system, such as:
- complex surroundings (metal bridges, tunnels, roads with barriers at the edge, etc.);
- poor weather conditions (snow, hail, black ice, etc.).
Risk of false alarms or absence of warnings
In the event of the system behaving abnormally, deactivate it and consult an authorised dealer.
2.53
BLIND SPOT WARNING (7/7)
Limitation of the system operation
- The radar area should be kept clean and free of any modifications in order to ensure the proper operation of the
system.
- Small objects moving close to the vehicle (motorcycles, bicycles, pedestrians, etc.) may not be recognised by the system.
- When turning into a bend, the radars may temporarily cease to detect vehicles in adjacent lanes.
- The function may warn you late if two other vehicles are approaching from the rear, driving side by side in the adjacent lanes
(i.e. driving on a 3-lane road) at a much higher speed than your vehicle.
- The system may not provide a warning when the other vehicles are travelling at a significantly different speed.
- If the vehicle is being overtaken by a long vehicle (e.g. heavy goods vehicle overtaking at a similar speed to the vehicle) the
system may interrupt the warning before the end of the manoeuvre.
- The vehicle is travelling on a winding road.
Deactivating the function
You must disable the function if:
- the radar area has been damaged (rear bumper);
- the vehicle is fitted with a towbar that is not recognised by the system.
2.54
SAFE DISTANCE ALERT (1/4)
Note: ensure that the windscreen and
1
the bumper are not obscured (by dirt,
mud, snow, condensation forming,
etc.).
The function is activated when the vehi-
cle speed is between about 19 and
124 mph (30 and 200 km/h).
2
Using the information from the radar 2
and camera 1, this function informs the
driver of the time interval between their
vehicle and the vehicle in front so that a
safe stopping distance between the two
vehicles can be maintained.
This function is an addi-
tional driving aid. This func-
tion is not under any cir-
cumstances intended to
replace the due care and attention
of the driver, who should at all times
be in control of the vehicle.
2.55
SAFE DISTANCE ALERT (2/4)
- press the 5 or 6 control repeatedly to
reach the “Distance warning” menu.
Press the switch 7 OK;
3
- Press the switch 7 OK again to acti-
vate or deactivate the function:
=
function activated
<
function deactivated
4
5
7
6
Activating/deactivating the
Vehicles not fitted with a multimedia
screen
function
- With the vehicle stopped, press the
Vehicles fitted with a multimedia
switch 4 as many times as required
screen 3
to reach the “Vehicle” tab;
To activate or deactivate the function,
- press the 5 or 6 control repeatedly to
refer to the multimedia instructions.
reach the “Settings” menu. Press the
Select “ON” or “OFF”.
switch 7 OK;
- press the 5 or 6 control repeatedly to
reach the “DRIVING ASSIST” menu.
Press the switch 7 OK;
Each time the vehicle is started,
the function continues the mode
saved the last time the engine was
stopped.
2.56
SAFE DISTANCE ALERT (3/4)
- C (orange): the time interval falls be-
8
tween around 1 and 2 seconds (in-
A
sufficient distance between the two
vehicles);
- D (red): the time interval is less than
or equal to around one second (very
The measurement is dis-
B
insufficient distance between the two
played for information: the
vehicles).
system does not carry out
any action on the vehicle.
If the interval between the two vehi-
C
cles is less than approximately 0.5 sec-
This function is not designed for use
onds, the 8 indicator and the D display
in urban conditions or for a dynamic
will flash in red on the instrument panel
driving style (sudden cornering, ac-
along with “-.- s”.
celeration, braking, etc.), but rather
D
for stable driving conditions.
Under certain conditions, the time inter-
val may not be displayed:
The function does not interact with
Operation
the braking system.
- while cornering;
With the function activated, the 8 in-
The radar and camera zones must
- when changing lane;
dicator is displayed on the instrument
be kept clean and free of any tam-
panel and informs the driver of the dis-
- if the vehicle in front is sufficiently far
pering in order to ensure the proper
tance between their vehicle and the ve-
or outside the range of the radar or
operation of the system.
hicle in front.
camera.
Any work carried out in the area
- A (grey): function not operational;
where the radar or camera is lo-
cated (repairs, replacements, wind-
- A (green): no vehicle detected;
screen and/or bumper modifica-
- B (green): the time interval is greater
tions, etc.) must be carried out by a
than or equal to around two seconds
qualified professional.
(distance between the two vehicles
adapted to your speed);
2.57
SAFE DISTANCE ALERT (4/4)
This function is an additional driving aid. This function is not under any circumstances intended to replace the due care
and attention of the driver, who should at all times be in control of the vehicle.
System servicing/repairs
- In the event of an impact, the radar and/or camera alignment may be changed and its operation may consequently be af-
fected. Deactivate the function and consult an authorised dealer.
- Any work carried out in the area where the radar and/or camera is located (replacements, repairs, windscreen and/or
bumper modifications, etc.) must be carried out by a qualified professional.
Only an authorised dealer is qualified to service the system.
In the event of system disturbance
- obstruction of the windscreen or the bumper (by dirt, glass, snow, condensation, etc.);
- a complex environment (metal bridge, tunnel etc.);
- poor weather conditions (snow, hail, black ice etc.);
- poor visibility (night, fog etc.);
- poor contrast between the vehicle preceding it and the surrounding area (e.g. white vehicle in a snowy area etc.) ;
- being dazzled (glaring sun, lights of vehicles travelling in the opposite direction etc.);
- the road is narrow, winding and undulating (tight bends etc.)
Risk of erroneous false alarms.
2.58
360° CAMERA (1/10)
1
5
4
2
2
3
Using information from cameras 1, 2,
Operation
- front side view (depending on the ve-
and 3 located in the front bumper, door
hicle): using camera 2 (passenger
The cameras transmit four separate
mirrors and on the tailgate, as well as
side).
views to the multimedia screen 5.
ultrasonic detectors 4 located in the ve-
They enable you to view the vehicle
The ultrasonic detectors detect obsta-
hicle bumpers, the feature assists with
surroundings:
cles at the front, rear and (depending
difficult manoeuvres (e.g. parking) by
- front view: using camera 1;
on the vehicle) side of the vehicle.
displaying the vehicle surroundings.
- rear view: using camera 3;
Note: make sure that the cameras are
- bird’s eye view: using cameras 1, 2
not obscured (by dirt, mud, snow etc.).
and 3;
This function is an additional aid. It cannot, therefore, under any circumstances replace the vigilance or the responsi-
bility of the driver.
The driver should always be ready for sudden incidents while driving: always ensure that there are no small, narrow
moving obstacles (such as a child, animal, pushchair, bicycle, stone, post, etc.) in the blind spot when manoeuvring.
2.59
360° CAMERA (2/10)
5
6
7
A
B
1
Front view 1
The fixed clearance gauge comprises
coloured markers A and B indicating
The view of the front camera is dis-
the distance behind the vehicle:
played on the multimedia screen 5.
- B(yellow) approximately 70 centi-
Fixed clearance gauge 6
metres from the vehicle;
The driver should be aware about
the blind zone which exists approxi-
The “front” view transmitted to the mul-
- A(green) approximately 150 centi-
mately up to 40cm from the end of
timedia screen 5 is displayed with one
metres from the vehicle.
front bumper on “Front view” mode
or two guidelines 6 and 7.
of 360° camera. In order to avoid
Dynamic gauge 7 (depending on the
This system is initially used with the aid
any risk of accident, a driver should
vehicle)
of several gauges (mobile for trajectory
be cautious of visual and auditory
and fixed for distance).
This is shown in blue on the multime-
warning supported from the park-
dia screen 5. It indicates the vehicle tra-
ing assist system. Parking assist
jectory according to the position of the
system displays the distance is
steering wheel in the front view.
shown in the 360° view with colored
indicator lines for each sensor that
registers an obstacle.
2.60
360° CAMERA (3/10)
5
6
7
3
A
B
C
Rear view 3
The fixed clearance gauge comprises
Dynamic gauge 7 (depending on the
coloured markers A, B and C indicating
vehicle)
The view of the rear camera is dis-
the distance behind the vehicle:
played on the multimedia screen 5.
This is shown in blue on the multime-
- C(red) approximately 30 centime-
dia screen 5. It indicates the vehicle tra-
Fixed clearance gauge 6
tres from the vehicle (rear view only);
jectory according to the position of the
steering wheel in the rear view.
The “rear” view transmitted to the multi-
- B(yellow) approximately 70 centi-
media screen 5 is displayed with one or
metres from the vehicle;
two guidelines 6 and 7.
- A(green) approximately 150 centi-
This system is initially used with the aid
metres from the vehicle.
of several gauges (mobile for trajectory
and fixed for distance).
The 5 multimedia screen shows a
reverse image of the rear view 3 as
in a rear view mirror.
2.61
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст