Daewoo Nubira. Manual — part 207
INTERIOR TRIM 9G – 29
DAEWOO V–121 BL4
GENERAL DESCRIPTION
AND SYSTEM OPERATION
INTERIOR TRIM PANELS
The interior trim panels are molded plastic and fasten with
screws, bolts or plastic clips.
PRESSURE RELIEF VENT
When all the windows are closed and the ventilation sys-
tem is on, the addition of outside air to the interior of the
vehicle causes a positive pressure within the vehicle. In or-
der to relieve the pressure, air is released through two
pressure relief vents. The pressure relief vents are located
at the rear quarter of the vehicle, behind the bumper fas-
cia.
REAR COMPARTMENT SECURITY
COVER
A rear compartment security cover is provided on the
hatchback and wagon. The rear compartment security
cover can be easily removed if more cargo space is need-
ed.
FLOOR CONSOLE
The floor console fits over the tunnel in the floor of the ve-
hicle and extends from under the center of the instrument
panel to the rear seat area. The floor console contains the
transaxle shift lever, the parking brake lever, and an ash-
tray for the rear seat occupants.
The sensing and diagnostic module (SDM) for the air–bag
system is located under the floor console.
FLOOR CARPET
The molded one–piece floor carpet goes over both the
front and the rear floor pans.
SECTION : 8A
SEAT BELTS
CAUTION : Disconnect the negative battery cable before removing or installing any electrical unit or when a tool
or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable will help
prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise noted.
TABLE OF CONTENTS
SPECIFICATIONS
8A–1
. . . . . . . . . . . . . . . . . . . . . . . . . .
FASTENER TIGHTENING SPECIFICATIONS
8A–1
.
SCHEMATIC AND WIRING DIAGRAMS
8A–2
. . . . . . .
DRIVER SEAT BELT WARNING
8A–2
. . . . . . . . . . . . .
DIAGNOSIS
8A–3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DRIVER SEAT BELT WARNING
8A–3
. . . . . . . . . . . . .
MAINTENANCE AND REPAIR
8A–5
. . . . . . . . . . . . . . .
ON–VEHICLE SERVICE
8A–5
. . . . . . . . . . . . . . . . . . . . .
PRETENSIONER FRONT SEAT BELT
8A–5
. . . . . . .
FRONT SEAT BELT HEIGHT ADJUSTER
8A–7
. . . .
THREE–POINT CLR REAR OUTBOARD SEAT BELT
8A–7
THREE–POINT CLR REAR CENTER SEAT BELT 8A
–9
CHILD SEAT TETHER ANCHOR
8A–10
. . . . . . . . . . .
GENERAL DESCRIPTION AND SYSTEM
OPERATION
8A–12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DRIVER SEAT BELT WARNING
8A–12
. . . . . . . . . . . .
PRETENSIONER FRONT SEAT BELT
8A–12
. . . . . .
THREE–POINT CLR REAR OUTBOARD SEAT BELT
8A–12
TWO–POINT LAP REAR CENTER SEAT BELT
8A–
12
OPERATIONAL AND FUNCTIONAL CHECKS 8A–12
CHILD SEAT TETHER ANCHOR
8A–12
. . . . . . . . . . .
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Application
N
S
m
Lb–Ft
Lb–In
Child Seat Tether Anchor
Bolt
25
18
–
Seat Belt Anchor Bolt
35
26
–
Seat Belt Height Adjuster
Bolts
19
14
–
Seat Belt Retractor Bolt
35
26
–
Seat Belt Retractor Screw
10
26
89
8A – 2
I
SEAT BELTS
DAEWOO V–121 BL4
SCHEMATIC AND WIRING DIAGRAMS
DRIVER SEAT BELT WARNING
SEAT BELTS 8A – 3
DAEWOO V–121 BL4
DIAGNOSIS
DRIVER SEAT BELT WARNING
Seat Belt Warning Lamp Does Not Turn On at Any Time
Step
Action
Value(s)
Yes
No
1
1. Unbuckle the seat belt.
2. Close the vehicle doors.
3. Turn the ignition ON.
Is the seat belt warning chime OK?
Go to Step 14
Go to Step 2
2
Check the seat belt warning fuse F5.
Is fuse F5 blown?
Go to Step 3
Go to Step 4
3
1. Check for a short circuit and repair if neces-
sary.
2. Replace the fuse.
Is the repair complete?
System OK
4
1. Turn the ignition ON.
2. Check the voltage at fuse F5.
Is the voltage equal to the specified value?
11–14 v
Go to Step 6
Go to Step 5
5
Repair the open power supply circuit for fuse F5.
Is the repair complete?
System OK
6
1. Disconnect the seat belt switch connector (lo-
cated under the driver
’
s seat).
2. Connect a jumper between the terminals on the
harness side of the seat belt switch connector.
3. Turn the ignition ON.
Does the seat belt warning lamp turn on?
Go to Step 7
Go to Step 8
7
Replace the seat belt switch.
Is the repair complete?
System OK
8
1. Disconnect the chime module electrical con-
nector.
2. Turn the ignition ON.
3. Check the voltage at terminal 8 of the chime
module connector.
Is the voltage equal to the specified value?
11–14 v
Go to Step 10
Go to Step 9
9
Repair the open circuit between fuse F5 and the
chime module.
Is the repair complete?
System OK
10
1. Leave the chime module connector discon-
nected.
2. Turn the ignition OFF.
3. Use an ohmmeter to measure resistance be-
tween ground and terminal 5 of the chime mod-
ule.
Is the resistance equal to the specified value?
[
0
W
Go to Step 12
Go to Step 11
11
Repair the ground circuit for the chime module.
Is the repair complete?
System OK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст