Hyundai Sonata (2022 year). Manual in english — page 7
Convenience Features
Programming
To program most devices, follow these
instructions:
ODN8A059137
4. Press the Original Transmitter
button until the indicator (4) is
turned continuously ON or flashes in
ODN8A059136
Green for approximately 10 seconds
1. Press and release (1), (2) or (3) button.
and it indicates the programing is
• If the indicator (4) is turned ON in
completed.
Orange, go to Step 3) since it is a
5. However, the indicator (4) flashes
new programming.
in Green continuously, but if the
• If the indicator (4) is continuously
garage door opener does not operate,
turned ON or flashes in Green rapidly
please continue to follow the step 6
several times, go to Step 2) since it is
and 7 (“Rolling Code Programming”
a programmed button.
procedures).
2. Press and hold the button you wish
6. Firmly press and release the “Learn,”
to program for approximately 15-
“Smart,” or “Program” button while
25 seconds until the LED flashes in
the indicator (4) flashes in Green.
Orange for several times.
Once the button is pressed, you have
approximately 30 seconds to initiate
3. Hold the Garage Door Opener Original
Transmitter near the HomeLink Mirror.
the next step.
Information
At the garage door opener motor, (security
gate motor, etc.) locate the “Learn,”
“Smart,” or “Program” button. This
can usually be found where the hanging
antenna wire is attached to the motor-head
unit (see the device’s manual to identify
this button). The name and color of the
button may vary by manufacturer. A
ladder and/or second person may simplify
the following steps.
5-34
05
7. Return to the vehicle and firmly press,
Gate operator & Canadian programming
hold for two seconds and release the
During programming, your handheld
HomeLink button up to three times.
transmitter may automatically stop
Do not press the HomeLink button
transmitting. Continue to press the
rapidly. At this point programming
Integrated HomeLink® Wireless Control
is complete and your device should
System button while you press and re-
operate when the HomeLink button is
press (“cycle”) your handheld transmitter
pressed and released.
every two seconds until the frequency
signal has been learned. The indicator
light will flash slowly and then rapidly
Information
after several seconds upon successful
• Some garage door openers require to
training.
press the programmed button on the
mirror up to three times right after
the programming is just completed to
operate the garage door.
• The indicator (4) is turned ON in
Orange and flashes for about 60
seconds, during the programing mode
and if a programing is not succeeded
within the 60 seconds, the programing
mode will be abort.
HomeLink® should now activate your
ODN8A059136
rolling code equipped device.
Operating HomeLink®
1. Press and release one of the
HomeLink buttons (1, 2 or 3) that
programed.
2. The HomeLink indicator (4) will
operate as below:
- Indicates Green and is continuously
ON (Fixed Code Garage Door
Opener)
- Flashes in Green rapidly (Rolling
Code Garage Door Opener)
5-35
Convenience Features
Information
This device complies with Industry
Canada RSS-210 standard.
Operation is subject to the following three
conditions:
1. This device may not cause harmful
interference.
2. This device must accept any
interference received, including
interference that may cause undesired
ODN8A059138
operation.
Erasing HomeLink® buttons
3. Changes or modifications not expressly
1. Press and hold the button (1) and (3)
approved by the party responsible
simultaneously.
for compliance could void the user’s
2. The indicator (4) is turned
authority to operate the device.
continuously ON in orange for about
10 seconds.
3. Then the indicator (4) color changes
to Green and flashes rapidly.
Release the buttons once the green
indicator flashes.
4. Now HomeLink button (1), (2) and (4)
memories are all cleared.
NVS® is a registered trademark and
Z-Nav™ is a trademark of the Gentex
Corporation, Zeeland, Michigan.
HomeLink® is a registered trademark
owned by Johnson Controls,
Incorporated, Milwaukee, Wisconsin.
FCC ID: NZLUAHL5A
IC: 4112A-UAHL5A
5-36
05
Two Way Communication Programing
1. Complete the HomeLink
“Programming” first.
2. Before the first 10 times HomeLink
button is pressed after the
programming, the following steps
MUST occur to program two way
communication. (only for some older
garage doors)
ODN8A059137
5. If the both indicator (4) and (6) are
flashing rapidly for about 5 seconds,
the two way synchronization is
completed.
Information
Some newer garage door openers provide
two-way communication synchronizing
ODN8A059139
when programming the original
transmitter.
3. Press and release the programed
HomeLink button to activate the
garage door.
4. Once the garage door is stopped,
press and release the “Learn” or
“Smart” button on the Garage door
opener within 1 minute from the time
of pressing the programed HomeLink
button on mirror.
5-37
Convenience Features
Recalling Garage Door Status
Homelink mirror with two way
communication provides a way to view
the last stored message from the garage
door opener. In order to recall the last
known status of the last activated device,
press the buttons “1 and 2” OR “2 and 3”
simultaneously.
• If the indicator (4) is ON continuously
in Green, it indicates that the last
activated device was “closed” properly.
ODN8A059139
• If the indicator (6) is ON continuously
Operating Two Way Communication
in Green, it indicates that the last
1. Press and release (1), (2) or (3) button.
activated device was “open” properly.
Information
Two way communication range distance
between “vehicle” and “garage door
opener” is 100m.
The range may be reduced or increased
a little due to obstacle conditions around
the garage door opener, such as houses or
trees.
ODN8A059140
2. The indicator (4) and (6) operates as
below:
- If the indicator (4) flashes in Orange,
it indicates that the garage door is
“closing”.
- If the indicator (4) is ON continuously
in Green, it indicates that the garage
door is “closed”.
- If the indicator (6) flashes in Orange,
it indicates that the garage door is
“Opening”.
- If the indicator (6) is ON
continuously in Green, it indicates
that the garage door is “Opened”.
- If the indicator (4) or (6) does not
turn to Green, it indicates that the
last status of garage door was not
received properly. The HomeLink
mirror tries to receive the last
known status of the garage door for
a few seconds.
5-38
05
Side View Mirrors
WARNING
Do not adjust or fold the side view
mirrors while driving. This may cause
loss of vehicle control resulting in an
accident.
NOTICE
•
Do not scrape ice off the mirror face;
this may damage the surface of the
glass.
•
If the mirror is jammed with ice, do
ODN8059024
not adjust the mirror by force. Use an
Make sure to adjust the side view mirrors
approved spray de-icer (not radiator
to your desired position before you begin
antifreeze) spray, or a sponge or soft
driving.
cloth with very warm water, or move
the vehicle to a warm place and
Your vehicle is equipped with both
allow the ice to melt.
left-hand and right-hand side view
mirrors. The mirrors can be adjusted
remotely with the remote switch. The
side view mirrors can be folded to help
prevent damage when going through
an automatic car wash or when passing
through a narrow street.
The right side view mirror is convex.
Objects seen in the mirror are closer than
they appear.
Use the inside rear view mirror or look
back directly to determine the actual
distance of other vehicles prior to
changing lanes.
5-39
Convenience Features
Side View Mirror Adjustment
Folding the side view mirrors
ODN8A059026
ODN8059024L
Adjusting the side view mirrors:
To fold the side view mirrors, grasp the
housing of the mirror and then fold it
1. Press either the L (driver’s side) or R
inwards.
(passenger’s side) button (1) to select
the side view mirror you would like to
adjust.
2. Use the mirror adjustment control
switch to position the selected mirror
up, down, left or right.
3. After adjustment, put the button into
neutral (center) position to prevent
inadvertent adjustment.
NOTICE
• The mirrors stop moving when
they reach the maximum adjusting
angles, but the motor continues to
operate while the switch is pressed.
Do not press the switch longer than
necessary, because this can damage
the motor.
• Do not attempt to adjust the side
view mirrors by hand, because this
can damage the motor.
5-40
05
Reverse Parking Aid Function
(if equipped)
ODN8A059028
When you press the R (Reverse) button,
the side view mirror(s) will rotate
downwards to aid with driving in reverse.
The position of the side view mirror
switch (1) determines whether or not the
mirrors will move:
Left/Right : When either the L (Left) or
R (Right) switch is selected,
both side view mirrors will
move.
Neutral : When neither switch is selected,
the side view mirrors will not
move.
The side view mirrors will automatically
revert to their original positions if any of
the following occur:
• The ignition switch is placed to either
the LOCK/OFF position or the ACC
position.
• The shift button is selected to any
position except R (Reverse).
• The remote control side view mirror
switch is not selected.
5-41
Convenience Features
WinDoWs
ODN8A059030
(1) Driver’s door power window switch
(2) Front passenger’s door power window switch
(3) Rear door (left) power window switch
(4) Rear door (right) power window switch
(5) Window opening and closing
(6) Automatic power window
(7) Power window lock switch
5-42
05
Power Windows
Window opening and closing
The ignition switch must be in the
ON position to be able to raise or
lower the windows. Each door has a
Power Window switch to control that
door’s window. The driver has a Power
Window Lock switch which can block
the operation of passenger windows.
The power windows will operate for
approximately 30 seconds after the
ignition switch is placed in the ACC or
LOCK/OFF position. However, if the front
doors are opened, the Power Windows
ODN8059031
will not operate even within the 30
To open:
second period.
Press the window switch down to the
first detent position (5). Release the
WARNING
switch when you want the window to
stop.
To avoid serious injury or death, do not
extend your head, arms or body outside
To close:
the windows while driving.
Pull the window switch up to the first
detent position (5). Release the window
Information
switch when you want the window to
•
In cold and wet climates, power
stop.
windows may not work properly due to
freezing conditions.
Auto down window (if equipped)
•
While driving with the rear windows
Pressing the power window switch
down or with the sunroof (if equipped)
down momentarily to the second
opened (or partially opened), your
detent position (6) completely lowers
vehicle may demonstrate a wind
the window even when the switch is
buffeting or pulsation noise. This
released. To stop the window at the
noise is normal and can be reduced
desired position while the window is in
or eliminated by taking the following
operation, pull up or press down and
actions. If the noise occurs with one
release the switch.
or both of the rear windows down,
partially lower both front windows
Auto up/down window (if equipped)
approximately 2.5 cm (1 inch). If you
Pressing or pulling up the power window
experience the noise with the sunroof
switch momentarily to the second
open, slightly close the sunroof.
detent position (6) completely lowers or
lifts the window even when the switch
is released. To stop the window at the
desired position while the window is in
operation, pull up or press down and
release the switch.
5-43
Convenience Features
To reset the power windows
Automatic reverse (if equipped)
If the power windows do not operate
normally, the automatic power window
system must be reset as follows:
1. Place the ignition switch to the ON
position.
2. Close the window and continue
pulling up on the power window
switch for at least one second.
If the power windows do not operate
properly after resetting, have the system
checked by an authorized HYUNDAI
ODN8059032
dealer.
If a window senses any obstacle while it
is closing automatically, it will stop and
WARNING
lower approximately 30 cm (12 inches) to
allow the object to be cleared.
The automatic reverse feature doesn’t
activate while resetting the power
If the window detects the resistance
window system. Make sure body parts
while the power window switch is
or other objects are safely out of the
pulled up continuously, the window
way before closing the windows to
will stop upward movement then lower
avoid injuries or vehicle damage.
approximately 2.5 cm (1 inch).
If the power window switch is pulled
up continuously again within 5 seconds
after the window is lowered by the
automatic window reverse feature,
the automatic window reverse will not
operate.
Information
The automatic reverse feature is only
active when the “Auto Up” feature is used
by fully pulling up the switch to the second
detent.
WARNING
Make sure body parts or other objects
are safely out of the way before closing
the windows to avoid injuries or vehicle
damage.
Objects less than 4 mm (0.16 inch) in
diameter caught between the window
glass and the upper window channel
may not be detected by the automatic
reverse window and the window will
not stop and reverse direction.
5-44
05
NOTICE
WARNING
Do not install any accessories on the
Do not allow children to play with the
windows. The automatic reverse
power windows. Keep the driver’s
feature may not operate.
door power window lock switch in the
LOCK position. Serious injury or death
Power window lock switch
can result from unintentional window
operation by a child.
NOTICE
• To prevent possible damage to the
power window system, do not open
or close two windows or more at the
same time. This will also ensure the
longevity of the fuse.
• Never try to operate the main
switch on the driver’s door and the
ODN8A059299
individual door window switch in
opposite directions at the same time.
The driver can disable the power window
If this is done, the window will stop
switches on the rear passenger doors by
pressing the power window lock switch.
and cannot be opened or closed.
When the power window lock switch is
pressed:
• The rear passenger control will not
be able to operate the rear passenger
power window
• Note that the front passenger control
is still able to operate the front
passenger window, and that the driver
master control can still operate all the
power windows.
5-45
Convenience Features
pAnorAmic SUnroof (if eQUippeD)
If your vehicle is equipped with a
WARNING
sunroof, you can slide or tilt your sunroof
with the sunroof control switch located
• Never adjust the sunroof or sunshade
on the overhead console.
while driving. This could result in
loss of control and an accident that
may cause death, serious injury, or
property damage.
• Make sure heads, hands, arms or
any other body parts or objects are
out of the way before operating the
sunroof.
• Do not extend your head, arms or
body outside the sunroof while
driving, to avoid serious injury.
• Do not leave the engine running
ODN8A059035
and the key in your vehicle with
The sunroof can only be opened, closed,
unsupervised children. Unattended
or tilted when the ignition switch is in the
children could operate the sunroof,
ON position.
which could result in serious injury.
The sunroof is operable for 30 seconds,
• Do not sit on the top of the vehicle. It
after the ignition switch is placed in the
may cause injury or vehicle damage.
OFF or ACC position. However, if the
front doors are opened, the sunroof
NOTICE
cannot be operated even within 30
seconds.
• Do not continue to move the sunroof
control lever after the sunroof is fully
opened, closed, or tilted. Damage
Information
to the motor or system components
could occur.
• In cold and wet climates, the sunroof
may not work properly due to freezing
• Make sure the sunroof is closed fully
conditions.
when leaving your vehicle.
• After the vehicle is washed or in a
If the sunroof is left open, rain or
rainstorm, be sure to wipe off any
snow may wet the interior of the
water that is on the sunroof before
vehicle. Also, leaving the sunroof
operating it.
open when the vehicle is unattended
may invite theft.
5-46
05
Sunshade
To stop the sunroof movement at any
point, push the sunroof control lever (1)
either forward or backward momentarily.
When the sunshade is opened
If you pull the sunroof control lever
backward, the sunroof glass will slide
all the way open. To stop the sunroof
movement at any point, pull or push the
sunroof control lever momentarily.
Information
ODN8A059036
Only the front glass of the sunroof opens
• To open the sunshade, pull the
and closes.
sunroof control lever (1) backward to
the first detent position.
Tilting the Sunroof
• To close the sunshade when the
sunroof glass is closed, push the
sunroof control lever (1) forward.
To stop the sunroof movement at any
point, push the sunroof control lever
either forward or backward momentarily.
Information
Activating the control lever to the first
detent requires only a very light touch.
ODN8A059038
Sliding the Sunroof
When the sunshade is closed
If you push the sunroof control lever
upward towards the roof of the vehicle,
the sunshade will slide open then the
sunroof glass will tilt open.
To stop the sunroof movement at any
point, push the sunroof control lever
either forward or backward momentarily.
When the sunshade is opened
If you push the sunroof control lever
ODN8A059037
upward, the sunroof glass will tilt open.
When the sunshade is closed
To stop the sunroof movement at any
If you push the sunroof control lever
point, push the sunroof control lever
(1) backward past the first detent, the
either forward or backward momentarily.
sunshade will slide all the way open and
then the sunroof glass will slide all the
way open.
5-47
Convenience Features
Closing the Sunroof
Automatic reverse (if equipped)
ODN8A059038
ODH043039
To close sunroof glass
If the sunroof senses any to an obstacle
while it is closing automatically, it will
Push the sunroof control lever (1) forward
reverse direction then stop to allow the
to the first detent position.
object to be cleared.
To close sunroof glass with
sunshade
WARNING
Push the sunroof control lever (1) forward
Small objects that can get caught
to the second detent position.
between the sunroof glass and the front
The sunroof glass will close, then the
glass channel may not be detected
sunshade will close automatically.
by the automatic reverse system. In
To stop the sunroof movement at any
this case, the sunroof glass will not
point, push the sunroof control lever (1)
detect the object and will not reverse
either forward or backward momentarily.
direction.
NOTICE
• Periodically remove any dirt that may
accumulate on the sunroof guide
rail or between the sunroof and roof
panel which can make a noise.
• Do not try to open the sunroof when
the temperature is below freezing
or when the sunroof is covered with
snow or ice, otherwise the motor
could be damaged. In cold and wet
climates, the sunroof may not work
properly.
5-48
05
Resetting the Sunroof
Information
If you do not reset the sunroof, it may not
work properly.
Sunroof Open Warning
(if equipped)
• If the driver turns off the engine
when the sunroof is not fully closed,
the warning chime will sound for
approximately 3 seconds and the
sunroof open warning will appear on
the cluster LCD display.
ODN8A059039
The sunroof may need to be reset if the
• If the driver turns off the engine and
following conditions occur:
opens the door when the sunroof is
not fully closed, the sunroof open
• The battery is discharged or
warning will appear on the cluster
disconnected or the sunroof fuse has
LCD display until the door is closed or
been replaced or disconnected
the sunroof is fully closed.
• The sunroof control lever is not
Close the sunroof securely when leaving
operating correctly
your vehicle.
To reset the sunroof, perform the
following steps:
1. Turn the engine on and close
the sunroof glass and sunshade
completely.
2. Release the control lever.
3. Push and hold the sunroof control
lever (1) forward (to close the
sunshade) for about 10 seconds until
the sunroof moves slightly, then
release the control lever.
4. Push and hold the sunroof control
lever forward until the sunroof
operates as follows:
TILT DOWN → SLIDE OPEN → SLIDE
CLOSE
Then, release the control lever.
When this is complete, the sunroof
system is reset.
For more information, contact an
authorized HYUNDAI dealer.
5-49
Convenience Features
exterior FeAtures
Hood
Closing the hood
Opening the hood
1. Before closing the hood, check in and
around the engine compartment to
ensure the following:
- Any tools or other loose objects are
removed from the engine room area
or hood opening area
- All glove, rags, or other combustible
material is removed from the engine
compartment
- All filler caps are tightly and
correctly installed
2. Lower the hood halfway (lifted
ODN8A059040
approximately 30 cm (12 inches) from
1.
Park the vehicle and set the parking
the closed position) and push down
brake.
to securely lock in place. Then double
2.
Pull the release lever to unlatch the
check to be sure the hood is secure.
hood. The hood should pop open
If the hood can be raised slightly, it is
slightly.
not securely locked. Open it again and
close it with more force.
WARNING
•
Before closing the hood, ensure
all obstructions are removed from
around the hood opening.
•
Always double check to be sure that
the hood is firmly latched before
driving away. Check there is no
hood open warning light or message
displayed on the instrument cluster.
ODN8A059041
Driving with the hood opened may
3. Go to the front of the vehicle, raise the
cause a total loss of visibility, which
hood slightly, push up the secondary
might result in an accident.
latch (1) inside of the hood center
•
Do not move the vehicle with the
and lift the hood (2). After it has been
hood in the raised position, as vision
raised about halfway, it will raise
is obstructed, which might result in
completely by itself.
an accident, and the hood could fall
or be damaged.
5-50
05
Trunk
Opening the trunk
ODN8059043
- Use the trunk release button.
ODN8059042
3. Lift the trunk lid up.
1. Make sure the shift button is in P
Closing the trunk
(Park).
Lower the trunk lid and press down until
2. Then do one of the following :
it locks.
- Press the button on the trunk handle
after locking or unlocking the door
by remote key or smart key.
WARNING
- Press the trunk unlock button of
Always keep the trunk lid completely
remote key or smart key for more
closed while the vehicle is in motion. If
than 1 second.
it is left open or ajar, poisonous exhaust
- Press the button on the trunk
gases containing carbon monoxide
itself with the Smart Key in your
(CO) may enter the vehicle and serious
possession.
illness or death may result.
WARNING
WARNING
The button on the trunk handle is
Make sure there are no people or
made of the rubber. Do not press it
objects around the trunk before
with the sharp objects such as the key,
opening or closing the Power Trunk.
screwdriver or drill.
Wait until the trunk is open fully and
stopped before loading or unloading
cargo from the vehicle.
NOTICE
To prevent damage to the trunk lift
cylinders and the attached hardware,
always close the trunk before driving.
5-51
Convenience Features
Emergency Trunk Safety Release
Information
Inside the trunk
In cold and wet climates, trunk lock and
trunk mechanisms may not work properly
due to freezing conditions.
WARNING
Always be careful to open and close the
trunk.
•
To prevent serious injury and
damage, you should check and keep
your body parts such as hands or
head away from the path of the trunk
ODN8059044L
while closing or opening the trunk.
Your vehicle is equipped with an
•
Your body parts or an object might
Emergency Trunk Safety Release lever
be damaged by sharp edges so you
located inside the trunk. When someone
should be careful while opening/
is inadvertently locked in the trunk, the
closing the trunk or taking the thing
trunk can be opened by moving the lever
out from the trunk. Especially, a child
in the direction of the arrow and pushing
can hit the face or head around the
the trunk open.
trunk so you should be cautious all
the time.
WARNING
•
You and your passengers must
be aware of the location of the
Emergency Trunk Safety Release
lever in this vehicle and how to open
the trunk in case you are accidentally
locked in the trunk.
•
NEVER allow anyone to occupy the
trunk of the vehicle at any time. If the
trunk is partially or totally latched
and the person is unable to get out,
serious injury or death could occur
due to lack of ventilation, exhaust
fumes and rapid heat build-up, or
because of exposure to cold weather
conditions. The trunk is also a highly
dangerous location in the event of a
crash because it is not a protected
occupant space but is a part of the
vehicle’s crush zone.
•
Your vehicle should be kept locked
and the Smart Key should be kept
out of the reach of children. Parents
should teach their children about the
dangers of playing in trunks.
•
Use the release lever for emergencies
only.
5-52
05
Inside the vehicle
How to use the Smart Trunk with
Auto Open
When you can not unlock the trunk due
to battery discharge or other reasons,
The trunk can be opened with no-touch
you can unlock the trunk inside the
activation satisfying all the conditions
vehicle.
below.
• After 15 seconds when all doors are
closed and locked
• Positioned in the detecting area for
more than 3 seconds.
Information
• The Smart Trunk with Auto Open does
not operate when:
- The smart key is detected within 15
seconds after the doors are closed and
ODN8059045L
locked, and is continuously detected.
Open the cable cover(1) under the rear
- The smart key is detected within 15
seat with a mechanical key and pull the
seconds after the doors are closed and
cable (2) for unlocking the trunk.
locked, and within 1.5m (60inches)
The cable is firmly fixed so it may hard to
from the front door handles. (for
pull. Therefore, please use a tool such as
vehicles equipped with Welcome
a screwdriver to assist in pulling the loop
Light)
for the emergency release.
- A door is not locked or closed.
Smart Trunk with Auto Open
- The smart key is in the vehicle.
(if equipped)
1. Setting
To activate the Smart Trunk with Auto
Open, go to User Settings Mode and
select Smart Trunk on the LCD display.
For more information, refer to the “LCD
Display” section in this chapter. If your
vehicle is equipped with additional
navigation, please refer to the
infotainment system manual separately
supplied.
ODN8059046L
On a vehicle equipped with a smart key,
the trunk can be opened using the Smart
Trunk with Auto Open system.
5-53
Convenience Features
ODN8A059047
ODN8A059048
2. Detect and Alert
3. Automatic opening
If you are positioned in the detecting
The hazard warning lights will blink and
area (50 ~100 cm (20~40 inches) behind
chime will sound 6 times and then the
the vehicle) carrying a smart key, the
trunk will open.
hazard warning lights will blink and
chime will sound to alert you the smart
key has been detected and the trunk will
WARNING
open.
• Make sure you close the trunk before
driving your vehicle.
• Make sure there are no people or
Information
objects around the trunk before
Do not approach the detecting area if you
opening or closing the trunk.
do not want the trunk to open. If you have
• Make sure objects in the trunk do not
unintentionally entered the detecting area
come out when opening the trunk on
and the hazard warning lights and chime
a slope. It may cause serious injury.
starts to operate, leave the detecting area
with the smart key. The trunk will stay
• Make sure to deactivate the Smart
closed.
Trunk when washing your vehicle.
Otherwise, the trunk may open
inadvertently.
• The key should be kept out of
reach of children. Children may
inadvertently open the Smart Trunk
while playing around the rear area of
the vehicle.
5-54
05
How to deactivate the Smart Trunk
Information
with Auto Open function using the
•
If you press the door unlock button
smart key
(2), the Smart Trunk with Auto
Type A
Open function will be deactivated
temporarily. But, if you do not open
any door for 30 seconds, the Smart
Trunk with Auto Open function will be
activated again.
•
If you press the trunk open button
(3) for more than 1 second, the trunk
opens.
•
If you press the door lock button (1) or
trunk open button (3) when the Smart
ODN8A059006
Trunk with Auto Open in the Detect
and Alert stage, the Smart Trunk
Type B
with Auto Open function will not be
deactivated.
•
In case you have deactivated the Smart
Trunk with Auto Open function by
pressing the smart key button and
opened a door, the Smart Trunk with
Auto Open function can be activated
again by closing and locking all doors.
ODN8A059007
(1) Door lock
(2) Door unlock
(3) Trunk open
If you press any button of the smart key
during the Detect and Alert stage, the
Smart Trunk with Auto Open function will
be deactivated.
Make sure to be aware of how to
deactivate the Smart Trunk with Auto
open function for emergency situations.
5-55
Convenience Features
Detecting area
Fuel Filler Door
Opening the fuel filler door
ODN8059049L
•
The Smart Trunk with Auto Open
ODN8059050
operates with a welcome alert if the
1. Turn the engine off.
smart key is detected within 50 ~ 100
2. Ensure the driver’s door is unlocked.
cm (20~40 inches) from the trunk.
3. Push the fuel filler door near the 3
•
The alert stops at once if the smart
o’clock position.
key is positioned outside the
detecting area during the Detect and
Alert stage.
Information
•
The Smart Trunk with Auto Open
function will not work if any of the
following occurs:
- The smart key is close to a radio
transmitter such as a radio station or
an airport which can interfere with
normal operation of the transmitter.
ODN8059051
- The smart key is near a mobile two
3. Pull the fuel filler door (1) outward to
way radio system or a cellular phone.
access the fuel tank cap.
- Another vehicle’s smart key is being
4. To remove the fuel tank cap (2), turn
operated close to your vehicle.
it counterclockwise. You may hear a
•
The detecting range may decrease or
hissing noise as the pressure inside
increase when :
the tank equalizes.
- One side of the tire is raised to replace
5. Place the cap on the fuel filler door.
a tire or to inspect the vehicle.
- The vehicle is parked on a slope or
unpaved road, etc.
5-56
05
•
Do not get back into a vehicle
Information
once you have begun refueling.
If the fuel filler door does not open
You can generate a buildup of
because ice has formed around it, tap
static electricity by touching,
lightly or push on the door to break the
rubbing or sliding against any item
ice and release the door. Do not pry on the
or fabric capable of producing
door. If necessary, spray around the door
static electricity. Static electricity
with an approved deicer fluid (do not use
discharge can ignite fuel vapors
radiator antifreeze) or move the vehicle to
causing a fire. If you must re-enter
a warm place and allow the ice to melt.
the vehicle, you should once again
eliminate potentially dangerous
Closing the fuel filler door
static electricity discharge by
touching a metal part of the vehicle,
1. To install the fuel tank cap, turn it
clockwise until it “clicks” one time.
away from the fuel filler neck, nozzle
or other gasoline source, with your
2. Close the fuel filler door until it is
bare hand.
latched securely.
•
When using an approved portable
fuel container, be sure to place the
WARNING
container on the ground prior to
refueling. Static electricity discharge
Gasoline is highly flammable and
from the container can ignite fuel
explosive. Failure to follow these
vapors causing a fire.
guidelines may result in SERIOUS
INJURY or DEATH:
Once refueling has begun, contact
between your bare hand and the
• Read and follow all warnings posted
vehicle should be maintained until
at the gas station.
the filling is complete.
• Before refueling, note the location of
•
Use only approved portable plastic
the Emergency Gasoline Shut-Off, if
fuel containers designed to carry and
available, at the gas station.
store gasoline.
• Before touching the fuel nozzle, you
•
When refueling, always move the
should eliminate the potential build-
shift button to the P (Park) position
up of static electricity by touching
set the parking brake, and place
a metal part of the vehicle, a safe
the ignition switch to the LOCK/
distance away from the fuel filler
OFF position. Sparks produced by
neck, nozzle, or other gas source,
electrical components related to the
with your bare hand.
engine can ignite fuel vapors causing
• Do not use cellular phones while
a fire.
refueling. Electric current and/or
•
Do not use matches or a lighter and
electronic interference from cellular
do not smoke or leave a lit cigarette
phones can potentially ignite fuel
in your vehicle while at a gas station,
vapors and cause a fire.
especially during refueling.
•
Do not over-fill or top-off your
vehicle tank, which can cause
gasoline spillage.
5-57
Convenience Features
• If a fire breaks out during refueling,
leave the vicinity of the vehicle, and
immediately contact the manager
of the gas station and then contact
the local fire department. Follow any
safety instructions they provide.
• If pressurized fuel sprays out, it can
cover your clothes or skin and thus
subject you to the risk of fire and
burns. Always remove the fuel cap
carefully and slowly. If the cap is
venting fuel or if you hear a hissing
sound, wait until the condition stops
before completely removing the cap.
• Always check that the fuel cap is
installed securely to prevent fuel
spillage in the event of an accident.
Information
Make sure to refuel your vehicle according
to the “Fuel Requirements” suggested in
the Introduction chapter.
NOTICE
• Do not spill fuel on the exterior
surfaces of the vehicle. Any type of
fuel spilled on painted surfaces may
damage the paint.
• If the fuel filler cap requires
replacement, use only a genuine
HYUNDAI cap or the equivalent
specified for your vehicle. An
incorrect fuel filler cap can result
in a serious malfunction of the fuel
system or emission control system.
5-58
05
heAD Up DiSplAy (hUD) (if eQUippeD)
WARNING
• Do not tint the front windshield
glass or add other types of metallic
coating. Otherwise, the head up
display image may be invisible.
• Do not place any accessories on the
crash pad or attach any objects on
the windshield glass.
• The Blind-spot Collision Warning
system warnings on the head up
ODN8A059054C
display are supplemental. Do not
The Head-Up Display is an optional
solely depend on them to change
feature that allows the driver to view
lanes. Always take a look around
information projected onto a transparent
before changing lanes.
screen while still keeping your eyes
safely on the road ahead while driving.
NOTICE
Precautions while using the head up
When replacing the front windshield
display
glass of the vehicle equipped with
the head up display, replace it with
It may sometimes be difficult to read
a windshield glass designed for the
information on the head up display in the
head up display operation. Otherwise,
following situations.
duplicated images may be displayed on
- The driver is improperly positioned in
the windshield glass.
the driver’s seat.
- The driver wears polarizing-filter
Head-up display ON/OFF
sunglasses.
- An object is located above the head
up display cover.
- The vehicle is driven on a wet road.
- Any improper lighting accessory is
installed inside the vehicle, or there
is incoming light from outside of the
vehicle.
- The driver wears glasses.
- The driver wears contact lenses.
OIK047152N
When it is difficult to read the head up
display information, adjust the head
To activate the head up display, select
up display angle or the head up display
‘Enable Head-Up Display’ on the User
brightness level in the User Settings
Settings mode on the instrument cluster
mode. For more information, refer to
LCD display.
“LCD Display” in this chapter.
If you do not select ‘Enable Head-Up
Display’, the head up display will be
deactivated.
If your vehicle is equipped with
additional navigation, please refer to the
infotainment system manual separately
supplied.
5-59
Convenience Features
Head-up display information
Head-up display setting
On the LCD display, you can change the
head up display settings as follows.
• Enable Head-up display
• Display Height
• Rotation
• Brightness
• Content Selection
• Speed Size
• Speed Color
ODN8A059338C
For more information, refer to “LCD
1. Turn-by-turn (TBT) navigation
Display” in chapter 4. If your vehicle is
information
equipped with additional navigation,
please refer to the infotainment system
2. Road information
manual separately supplied.
3. Speedometer
4. Cruise system set speed
5. Smart Cruise Control information
6. Lane Following Assist system
information
7. Lane Keeping Assist system
information
8. Blind-spot Collision Warning system
information
9. Highway Driving Assist system
information
The information provided may differ
depending on which functions are
applicable to your vehicle.
Information
If you select the Turn By Turn (TBT)
navigation information as Head-Up
Display contents, the Turn By Turn
(TBT) navigation information will not be
displayed in the instrument cluster LCD
display.
5-60
05
lighting
Exterior Lights
Lighting control
To operate the lights, turn the knob at
the end of the control lever to one of the
following positions:
ODN8A059201
AUTO headlamp position
The parking lamp and headlamp will
be turned ON or OFF automatically
depending on the amount of daylight as
measured by the ambient light sensor on
ODN8A059200
the center dash (1).
1. OFF position
Even with the AUTO headlamp feature
2. AUTO headlamp position
in operation, it is recommended to
3. Parking lamp position
manually turn ON the headlamps when
driving at night or in a fog, driving in the
4. Headlamp position
rain, or when you enter dark areas, such
as tunnels and parking facilities.
Daytime running light (DRL)
The Daytime Running Lights (DRL) can
NOTICE
make it easier for others to see the front
of your vehicle during the day, especially
• Do not cover or spill anything on
after dawn and before sunset.
the sensor (1) located in front of the
instrument panel.
The DRL system will turn the dedicated
• Do not clean the sensor using
lamp OFF when:
a window cleaner, the cleanser
• The headlamps are ON.
may leave a light film which could
interfere with sensor operation.
• The parking lamps are ON.
• If your vehicle has window tint or
• The vehicle is turned off.
other types of metallic coating on
• The parking brake is engaged.
the front windshield, the AUTO
headlamp system may not work
properly.
5-61
Convenience Features
High beam operation
ODN8A059202
Parking lamp position (
)
ODN8A059205
The parking lamp, license plate lamp and
To turn on the high beam headlamp,
instrument panel lamp are turned ON.
push the lever away from you. The lever
will return to its original position.
The high beam indicator will light when
the headlamp high beams are switched
on.
To turn off the high beam headlamp, pull
the lever towards you. The low beams
will turn on.
WARNING
Do not use high beam when there are
ODN8A059203
other vehicles approaching you. Using
high beam could obstruct the other
Headlamp position (
)
driver’s vision.
The headlamp, parking lamp, license
plate lamp and instrument panel lamp
are turned ON.
Information
The ignition switch must be in the ON
position to turn on the headlamp.
5-62
05
Operating condition
1. Place the headlamp switch in the
AUTO position.
2. Turn on the high beam by pushing the
lever away from you.
High Beam Assist (
) indicator will
illuminate.
3. High Beam Assist will turn on when
vehicle speed is above 40 km/h (25
mph).
ODN8A059204
• If the headlamp switch is pushed
To flash the high beam headlamp, pull
away when High Beam Assist
the lever towards you, then release the
system is operating, High Beam
lever. The high beams will remain ON as
Assist system will turn off and the
long as you hold the lever towards you.
high beam will be on continuously.
• If the headlamp switch is pulled
High Beam Assist (HBA)
towards you when the high beam
is OFF, the high beam will turn ON
without High Beam Assist system
canceled. When you let go of the
light switch, the lever will move to
the middle and the high beam will
turn OFF.
• If the headlamp switch is pulled
towards you when the high beam is
on by High Beam Assist system, the
low beam will be on and High Beam
Assist system will turn OFF.
OOS047409N
• If the headlamp switch is placed
High Beam Assist is a system that
to the headlamp ON position,
automatically adjusts the headlamp
High Beam Assist system will turn
range (switches between high beam and
off and the low beam will be on
low beam) according to the brightness of
continuously.
other vehicles and road conditions.
System setting
The driver can activate HBA by placing
the ignition switch to the ON position
and by selecting:
‘User Settings → Lights → High Beam
Assist’. If you disable this setting, HBA
will not work.
The setting of the HBA will be
maintained, as selected, when the
engine is re-started.
5-63
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст