Hyundai Sonata (2022 year). Manual in english — page 8
Convenience Features
When High Beam Assist system is
operating, the high beam switches to low
beam if any of the following conditions
occur:
-
When the headlamp of an on-coming
vehicle is detected.
-
When the tail lamp of a vehicle in front
is detected.
-
When the headlamp or tail lamp of a
motorcycle or a bicycle is detected.
-
When the surrounding ambient light is
OIK047132N
bright enough that high beams are not
Warning light and message
required.
When High Beam Assist system is not
-
When streetlights or other lights are
working properly, the Check High Beam
detected.
Assist warning message will come on
-
When the headlamp switch is not in
for a few seconds. After the message
the AUTO position.
disappears, the master warning light (
)
will illuminate. Take your vehicle to an
-
When High Beam Assist system is off.
authorized HYUNDAI dealer and have the
-
When vehicle speed is below 24 km/h
system checked.
(15 mph).
CAUTION
The system may not operate normally if
any of the following conditions should
occur:
1. When the illumination from an on-
coming vehicle or a vehicle in front is
dim. Such examples may include:
• When the headlamps of an on-
coming vehicle or the tail lamps of
a vehicle in front is covered with
dust, snow, or water.
• When the headlamps on an on-
coming vehicle are OFF, but the
fog lamps are ON.
5-64
05
2.
When the High Beam Assist camera
WARNING
is adversely affected by an external
condition. Such examples may
•
Do not attempt to disassemble
include:
the front view camera without the
assistance of an authorized HYUNDAI
• When the vehicle’s headlamps
dealer technician. If the front camera
have been damaged or not
is removed for any reason, the
repaired properly.
system may need to be re-calibrated.
• When the vehicle headlamps are
Have the system inspected by an
not aimed properly.
authorized HYUNDAI dealer.
• When the vehicle is driven on a
•
If the windshield of your vehicle is
narrow curved road or rough road
replaced, most likely the front view
• When the vehicle is driven on an
camera will need to be re-calibrated.
uphill road or downhill road
If this occurs, have your vehicle
inspected and have the system re-
• When only part of the vehicle in
calibrated by an authorized HYUNDAI
front is visible on a crossroad or
dealer.
curved road.
•
Be careful that water doesn’t get into
• When there is a traffic light,
High Beam Assist unit and do not
reflecting sign, flashing sign or
remove or damage related parts of
mirror.
High Beam Assist system.
• When the road conditions are bad
•
Do not place objects on the crash
such as being wet or covered with
pad that reflect light such as mirrors,
snow.
white paper, etc. The system may
• When a vehicle suddenly appears
malfunction if sunlight is reflected.
from a curve.
•
At times, High Beam Assist system
• When the vehicle is tilted from a
may not work properly. The system
flat tire or being towed.
is for your convenience only. It is the
• When Lane Keeping Assist system
responsibility of the driver for safe
warning light illuminates.
driving practices and always check
• When the light from the on-coming
the road conditions for your safety.
or front vehicle is not detected
•
When the system does not operate
because of exhaust fume, smoke,
normally, change the headlamp
fog, snow, etc.
position manually between the high
• When the front window is covered
beam and low beam.
with foreign matters such as ice,
dust, fog, or is damaged.
3.
When the forward visibility is poor.
Such examples may include:
• When the headlamps of an on-
coming vehicle or a vehicle in front
is not detected due to poor outside
visibility (smog, smoke, dust, fog,
heavy rain, snow, etc.).
• When the windshield visibility is
poor.
5-65
Convenience Features
Turn signals and lane change signals
Battery saver function
The purpose of this feature is to prevent
the battery from being discharged.
The system automatically turns off the
parking lamp when the driver turns the
vehicle off and opens the driver-side
door.
With this feature, the parking lamps will
turn off automatically if the driver parks
on the side of road at night.
However, the position lamps stay ON
even when the driver-side door is opened
ODN8A059207
if the headlamp switch is turned to the
To signal a turn, push down on the lever
position lamp or AUTO (if equipped)
for a left turn or up for a right turn in
position after the engine is turned off.
position (A).
If necessary, to keep the lamps on
If an indicator stays on and does not flash
turn the position lamps OFF and ON
or if it flashes abnormally, one of the turn
again using the headlamp switch on
signal bulbs may be burned out and will
the steering column after the engine is
require replacement.
turned off.
One touch turn signal function
Headlamp delay function
(if equipped)
To activate the One Touch Turn Signal
function, push the turn signal lever up or
If the key is removed from the ignition
down to position (B) and then release it.
switch or placed in the ACC position
or the LOCK/OFF position with the
The lane change signals will blink 3, 5 or
headlamps ON, the headlamps (and/
7 times.
or parking lamps) remain on for about
You can activate or deactivate the One
5 minutes. However, if the driver’s door
Touch Turn Signal function or choose
is opened and closed, the headlamps
the number of blinks (3, 5, or 7) from the
are turned off after 15 seconds. Also,
User Settings mode in the LCD display.
with the engine off if the driver’s door is
opened and closed, the headlamps (and/
or parking lamps) are turned off after 15
seconds.
The headlamps (and/or parking lamps)
can be turned off by pressing the lock
button on the remote key or smart key
twice or turning the headlamp switch to
the OFF or AUTO position.
You can activate or deactivate the
Headlamp Delay function from the User
Settings Mode in the LCD display.
5-66
05
NOTICE
Interior Lights
If the driver exits the vehicle through
another door besides the driver
WARNING
door, the battery saver function
does not operate and the headlamp
Do not use the interior lights when
delay function does not turn OFF
driving in the dark. The interior lights
automatically.
may obscure your view and cause an
accident.
This may cause the battery to
discharge. To avoid battery discharge,
turn OFF the headlamps manually from
NOTICE
the headlamp switch before exiting the
Do not use the interior lights for
vehicle.
extended periods when the vehicle is
turned off or the battery will discharge.
Headlamp leveling device
It automatically adjusts the headlamp
Interior lamp AUTO cut
beam level according to the number of
The interior lamps will automatically go
passengers and loading weight in the
off approximately 20 minutes after the
luggage area.
engine is turned off and the doors are
And it offers proper headlamp beam
closed. If a door is opened, the lamp
under various conditions.
will go off 40 minutes after the engine is
turned off. If the doors are locked by the
remote key or smart key and the vehicle
WARNING
enters the armed stage of the theft
If the function does not work properly,
alarm system, the lamps will go off five
have the vehicle inspected by an
seconds later.
authorized HYUNDAI dealer. Do not
attempt to inspect or replace the wiring
yourself.
5-67
Convenience Features
Front lamps
Rear lamp
Type A (without sunroof )
ODN8A059210
ODN8059211
Front Map Lamp (1):
Type B (with sunroof )
Press either lenses to turn the map lamp
on or off. This light produces a spot
beam for convenient use as a map lamp
at night or as a personal lamp for the
driver and the front passenger.
Front Door Lamp (2) (
):
The front or rear room lamps come on
when the front or rear doors are opened
if the engine is running or not. When
OLFP048099
doors are unlocked by the remote key or
Rear Room Lamp (
):
smart key, the front and rear lamps come
on for approximately 30 seconds as long
Press this switch to turn the rear room
lamp on and off.
as any door is not opened. The front and
rear room lamps go out gradually after
approximately 30 seconds when the door
NOTICE
is closed. However, if the ignition switch
Do not leave the lamp switches on for
is in the ON position or all doors are
an extended period of time when the
locked, the front and rear lamps will turn
engine is turned off.
off. If a door is opened with the ignition
switch in the ACC position or the OFF
position, the front and rear lamps stay on
for about 20 minutes.
Front room lamp (3)
:
Press the button to turn ON the room
lamp for the front/rear seats.
5-68
05
Luggage compartment lamp
Vanity mirror lamp
ODN8059213L
OOS047055
The luggage compartment lamp comes
Push the switch to turn the light on or off.
on when the trunk is opened.
•
: The lamp will turn on if this
button is pressed.
NOTICE
•
: The lamp will turn off if this
button is pressed.
The luggage compartment lamp comes
on as long as the trunk is open. To
prevent unnecessary battery system
NOTICE
drain, close the trunk securely after
Always have the switch in the off
using the luggage compartment.
position when the vanity mirror lamp
is not in use. If the sunvisor is closed
without the lamp off, it may discharge
the battery or damage the sunvisor.
5-69
Convenience Features
Welcome System (if equipped)
You can activate or deactivate the
Welcome Light from the User Settings
Welcome light
Mode on the LCD display.
For more information, refer to “LCD
Display” in chapter 4. If your vehicle is
equipped with additional navigation,
please refer to the infotainment system
manual separately supplied.
Interior lamp
When the interior lamp switch is in the
DOOR position and all doors (and trunk)
are closed and locked, the room lamp
will come on for 30 seconds if any of the
ODN8A059099
below is performed.
Door handle lamp
• When the door unlock button is
When all the doors (and trunk) are closed
pressed on the remote key or smart
and locked, the door handle lamp will
key.
come on for about 15 seconds if any of
• When the button of the outside door
the below is performed.
handle is pressed.
• When the door unlock button is
At this time, if you press the door lock or
pressed on the remote key or smart
key.
unlock button, the room lamp will turn
off immediately.
• When the button of the outside door
handle is pressed.
• When the vehicle is approached with
the smart key in possession.
Headlamp
When the headlamp (lamp switch in
the headlamp or AUTO position) is on
and all doors (and trunk) are locked
and closed, the headlamp will come on
for 15 seconds if/or any of the below is
performed.
• When the door unlock button is
pressed on the remote key or smart
key.
At this time, if you press the door lock or
unlock button, the headlamp will turn off
immediately.
5-70
05
Wipers AnD WAshers
Windshield Wipers
Operates as follows when the ignition
switch is in the ON position.
MIST: For a single wiping cycle, push
the lever upward and release. The
wipers will operate continuously if
the lever is held in this position.
OFF: Wiper is not in operation.
INT: Wiper operates intermittently at
the same wiping intervals. To vary
ODN8059208L
the speed setting, move the speed
A. Wiper speed control
control lever. The top most setting
will run the wipers most frequently
• MIST - Single wipe
(for more rain). The bottom setting
• OFF - Off
will run the wipers the least
• INT / --- - Intermittent wipe
frequently (for less rain).
AUTO - Auto control wipe
AUTO :
The rain sensor located
(if equipped)
(if equipped) on the upper end of the
• LO- Low wiper speed
windshield glass senses
• HI - High wiper speed
the amount of rainfall and
controls the wiping cycle
B. Intermittent control wipe time
for the proper interval. The
adjustment
more it rains, the faster the
C. Wash with brief wipes
wiper operates. When the
(pull lever towards you)
rain stops, the wiper stops.
To vary the speed setting,
turn the speed control knob
(B).
LO: The wiper runs at a lower speed.
HI: The wiper runs at a higher speed.
Information
If there is heavy accumulation of snow
or ice on the windshield, defrost the
windshield for about 10 minutes, or until
the snow and/or ice is removed before
using the windshield wipers to ensure
proper operation.
If you do not remove the snow and/or ice
before using the wiper and washer, it may
damage the wiper and washer system.
5-71
Convenience Features
Windshield Washers
Information
If the wiper switch is set in AUTO mode
when Engine Start/Stop button is in the
ON position, the wiper will operate once to
perform a self-check of the system. Set the
wiper to the OFF position when the wiper
is not in use.
WARNING
To avoid personal injury from the
windshield wipers, when the engine
ODN8059209K
is running and the windshield wiper
switch is placed in the AUTO mode:
In the OFF position, pull the lever gently
toward you to spray washer fluid on the
•
Do not touch the upper end of the
windshield glass facing the rain
windshield and to run the wipers 1-3
cycles. The spray and wiper operation
sensor.
will continue until you release the lever. If
•
Do not wipe the upper end of the
the washer does not work, you may need
windshield glass with a damp or wet
to add washer fluid to the washer fluid
cloth.
reservoir.
•
Do not put pressure on the
windshield glass.
WARNING
When the outside temperature is below
freezing, ALWAYS warm the windshield
using the defroster to help prevent
the washer fluid from freezing on the
windshield and obscuring your vision
which could result in an accident and
serious injury or death.
NOTICE
• To prevent possible damage to the
washer pump, do not operate the
washer when the fluid reservoir is
empty.
• To prevent possible damage to the
wipers or windshield, do not operate
the wipers when the windshield is
dry.
• To prevent damage to the wiper
arms and other components, do
not attempt to move the wipers
manually.
• To prevent possible damage to the
wipers and washer system, use anti-
freezing washer fluids in the winter
season or cold weather.
5-72
05
reAr view moniTor (rvm) (if eQUippeD)
Rear View Monitor system is a
Rear View Monitor - Top View
supplemental system that shows the area
behind the vehicle on the infotainment
system screen to assist you when parking
or driving.
Rear View Monitor with Parking
Guidance
ODN8H059062
When you touch the icon (1), the top view
is displayed on the screen and shows the
distance from the vehicle in the back of
your vehicle. Touch the icon (1) again, to
switch back to the previous screen.
ODN8059058
WARNING
Rear View Monitor is not a safety
device. It only serves to assist the driver
in identifying objects directly behind
the middle of the vehicle. The camera
does NOT cover the complete area
behind the vehicle.
ODN8059059
• Rear View Monitor with parking
guidance will activate when the
engine is running and the shift into R
(Reverse) position.
• To assist in parking, the rear view
is shown (the parking guide line
isappears) on the screen when the
shift button is shifted from R (Reverse)
to D (Drive) with vehicle speed below
10 km/h (6 mph).
5-73
Convenience Features
WARNING
• Never rely solely on the rear camera
display when backing-up.
• ALWAYS look around your vehicle
to make sure there are no objects or
obstacles before moving the vehicle
in any direction to prevent a collision.
• Always pay close attention when the
vehicle is driven close to objects,
particularly pedestrians, and
especially children.
NOTICE
• Do not spray the camera or its
surrounding area directly with a high
pressure washer. Shock applied from
high pressure water may cause the
device to not operate normally.
• Do not use any cleanser containing
acid or alkaline detergents when
cleaning the lens. Use only a mild
soap or neutral detergent, and rinse
thoroughly with water.
• Always keep the rear view camera
lens clean. If the lens is covered with
foreign material, it may adversely
affect camera performance and
Rear View Monitor may not operate
normally. However, do not use
chemical solvents such as strong
detergents containing high alkaline
or volatile organic solvents (gasoline,
acetone etc.). This may damage the
camera lens.
5-74
05
SUrroUnD view moniTor (Svm) (if eQUippeD)
•
When the vehicle is backing up,
the system will turn ON regardless
of vehicle speed or button status.
However, if vehicle speed is over 15
km/h (10 mph) when driving forward,
Surround View Monitor system will
turn off.
•
An indicator on the screen appears
when:
- The trunk is opened
ODN8059265
- The driver/passenger’s door is
opened
Surround View Monitor system can assist
in parking by allowing the driver to see
- The side view mirror is folded
around the vehicle.
•
When you set up ‘Surround View
Monitor Auto On’ on the user setting
Operating Conditions
menu, you can choose the Surround
View Monitor system to turn on
• The engine is running.
automatically in case of the parking
• The Surround View Monitor button(1)
alarm sounds.
is pressed (indicator ON).
•
If the system is not operating
• The gear status is on D (Drive), N
normally, have the vehicle inspected
(Neutral), R (Reverse). (On P (Park), it
by an authorized HYUNDAI dealer.
doesn’t work.)
• Vehicle speed is under 15km/h (10
mph).
CAUTION
•
Surround View Monitor system is
Deactivations
a parking assist system. Because
• The Surround View Monitor button (1)
the images of the four cameras on
is pressed again (indicator OFF).
the front, rear, left, and right are
synthesized, the SVM view and
• Vehicle speed is over 15km/h (10
parking guidelines may differ from
mph).
the actual vehicle location. So, check
all directions for safety.
System operation
•
Always keep the rear view camera
• When vehicle speed is over 15 km/h
lens clean. If the lens is covered with
(10 mph), the system will turn off. The
foreign material, it may adversely
system will not automatically turn on
affect camera performance and
again, even though vehicle speed gets
Surround View Monitor may not
below 15 km/h (10 mph). Press the
operate normally. However, do not
button (1, indicator ON) again, to turn
use chemical solvents such as strong
on the system.
detergents containing high alkaline
or volatile organic solvents (gasoline,
acetone etc.). This may damage the
camera lens.
5-75
Convenience Features
reverSe pArKinG colliSion-AvoiDAnce ASSiST
(if eQUippeD)
Reverse Parking Collision-Avoidance
System Setting and Operation
Assist (PCA) is a supplemental system
that can warn the driver or apply braking
System setting
force to reduce the possibility of collision
Parking Collision-Avoidance Assist-
with pedestrians when the vehicle is
Reverse (PCA-R) can be activated from
reversing.
the Settings menu in the LCD display or
infotainment system display by following
WARNING
the procedure below.
•
Always look around your vehicle to
1.
Set the Engine Start/Stop button to
the ON or START position.
make sure there are no objects or
pedestrian before moving the vehicle
2.
Select ‘User Settings → Driver
in any direction to prevent a collision.
Assistance → Parking Safety → Active
•
Do not solely rely on Reverse Parking
Assist / Warning Only / Off’ in the
LCD display or infotainment system
Collision-Avoidance Assist system.
The system might not assist the
display.
driver leading to pedestrian injury or
- The system is ready for operation
vehicle damage.
when 'Active Assist' is selected. In
•
Be aware that some objects may
the event of an imminent collision
with a pedestrian or an object, the
not be visible on the screen or be
detected by the rear ultrasonic
system warns the driver or applies
sensors, due to the objects’ distance,
braking force to help avoid the
size or material, all of which can limit
collision.
the effectiveness of the sensors.
- The system is ready for operation
when 'Warning Only' is selected. In
the event of an imminent collision
with a pedestrian, the system warns
the driver but does not assist in
braking.
- The system deactivates when 'Off' is
selected.
5-76
05
Operating conditions
Warning and System Control
Reverse Parking Collision-Avoidance
Assist system enters the ready status,
Active assist
when 'Active Assist' or 'Warning Only' is
Cluster LCD display
selected in the AVN system screen and
the following conditions are satisfied:
• The trunk is closed
• The shift lever is in R (Reverse)
• Vehicle speed is below 10 km/h (6 mph)
• System components such as the rear
view camera and the rear ultrasonic
sensors are in normal conditions
ODN8A049043
The driver needs to select 'Active Assist'
Infotainment system display
on the LCD display or infotainment
system display for collision-avoidance
assist.
The solid lines behind the vehicle in the
cluster LCD display indicates that the
system is ready to assist the driver.
Note that the system assists the driver
only once. The driver has to shift the gear
OHI059255N
to R (Reverse) from another gear position
to reactivate the system.
•
If the system detects a risk of collision
with a pedestrian or an object behind
the vehicle, the system will warn the
The performance of Reverse Parking
driver with audible warning, steering
Collision-Avoidance Assist system may
wheel vibration, and warnings on
vary under certain conditions. If the
the cluster LCD display and the
vehicle speed exceeds 3 km/h (2 mph),
infotainment system display.
the system can assist only pedestrian
•
If the system detects imminent
collision avoidance.
collision with a pedestrian or an object
behind the vehicle, the system may
As always, be careful when backing
apply braking power. The driver needs
up your vehicle and be aware of your
to pay attention as the brake will
surroundings.
release within 2 seconds. The driver
must immediately depress the brake
pedal and check surroundings.
5-77
Convenience Features
The brake assist will turn off when:
CAUTION
- The driver shifts the gear to P (Park) or
• Always pay attention to road
D (Drive)
and traffic conditions while
- The driver depresses the brake pedal
driving, whether or not there is
with sufficient power
a warning.
- The braking has been assisted for
approximately 2 seconds
• Playing the vehicle audio
system at high volume may
The warning will turn off when:
prevent occupants from hearing
Reverse Parking Collision-
- The driver shifts the gear to P (Park), N
(Neutral), or D (Drive)
Avoidance Assist system
warning sounds.
The brake control may not operate
• If any other warning sound,
properly depending on the status of the
such as seat belt warning
ESC (Electronic Stability Control). There
chime, is already generated,
will only be a warning when:
Reverse Parking Collision-
- The ESC (Electronic Stability Control)
Avoidance Assist system
warning light is on
warning may not sound.
- The ESC (Electronic Stability Control)
is engaged in a different function
Information
Warning only
The system can detect a pedestrian or an
• If the system detects a risk of collision
object when:
with a pedestrian or an object, the
-
A pedestrian is standing behind the
system will warn the driver with
vehicle.
audible warning and warnings on the
-
A large obstacle, such as a vehicle, is
cluster LCD display or infotainment
parked in the rear center of the vehicle.
system display.
• If ‘Warning Only’ is selected, braking
will not be assisted.
The warning will turn off when:
- The driver shifts the gear to P (Park), N
(Neutral), or D (Drive)
WARNING
• Reverse Parking Collision-
Avoidance Assist system may
not operate properly or may
operate unnecessarily in some
circumstances.
• Always pay extreme caution while
driving. The driver is responsible for
controlling the brake appropriately.
5-78
05
Detecting Sensor
NOTICE
Cluster LCD display
•
The system may turn off if interfered
by electromagnetic waves.
•
Always keep the rear view camera
and the ultrasonic sensors clean.
•
Do not use any cleanser containing
acid or alkaline detergents when
cleaning the rear view camera lens.
Use only a mild soap or neutral
detergent, and rinse thoroughly with
water.
•
NEVER disassemble the rear view
ODN8059058
camera or the ultrasonic sensor
Rear ultrasonic sensor
components or apply any impact
on the rear view camera or the
ultrasonic sensor components.
•
Do not apply unnecessary force
on the rear view camera or the
ultrasonic sensors. The system
may not operate properly if the
rear view camera or the ultrasonic
sensor(s) is forcibly moved out of
proper alignment. Have the vehicle
ODN8A059303
inspected by an authorized HYUNDAI
Rear view camera
dealer.
The rear view camera acquires images
•
Do not spray the rear view camera
for rear pedestrian detection. If the
or the ultrasonic sensors or their
camera lens is covered with snow, rain,
surrounding area directly with a high
or a foreign substance, the system may
pressure washer. Shock applied from
not work properly. Always keep the
high pressure water may cause the
camera lens clean.
device to malfunction.
•
The system may not work properly if
the bumper has been damaged, or if
Rear ultrasonic sensors
the rear bumper has been replaced
The rear ultrasonic sensors detect
or repaired.
objects. The sensors are installed in
•
Do not apply foreign objects, such as
the rear bumper. If the rear ultrasonic
a bumper sticker or a bumper guard,
sensor(s) is covered with snow, rain, or
near the camera or sensors or apply
a foreign substance, the system may
paint to the bumper. Doing so may
not work properly. Always keep the rear
adversely affect the performance of
bumper clean.
the system.
5-79
Convenience Features
Warning message
System Malfunction
Rear view camera
ODN8A049044
ODN8A049046
Rear ultrasonic sensor
Check Parking Collision-Avoidance Assist
system
If there is a problem with Reverse Parking
Collision-Avoidance Assist system
or other related systems, a warning
message will appear and the system will
turn off automatically. Have the vehicle
inspected by an authorized HYUNDAI
dealer.
ODN8A049045
Limitations of the System
Rear camera error or blockage/ Parking
Reverse Parking Collision-Avoidance
sensor error or blockage
Assist system may not assist braking
or alert the driver under the following
This warning message may appear when:
conditions even if there are pedestrians
- The rear view camera or the ultrasonic
or objects.
sensor(s) is blocked by dirt, snow, or a
• Any non-factory equipment or
foreign object.
accessories have been installed.
- There is inclement weather, such as
• The condition of the vehicle is
heavy snow, rain, etc.
unstable due to an accident or other
If any of these conditions occur, the
causes.
system may turn off automatically or not
• The height of the bumper or the
operate properly.
sensor installation has been modified.
• The rear view camera or the ultrasonic
When the warning message is displayed
sensor(s) is damaged.
in the cluster, make sure that the rear
• The rear view camera or the ultrasonic
view camera and the rear ultrasonic
sensor(s) is stained with foreign
sensors are clean.
matter, such as snow, dirt, etc.
• The rear view camera is obscured
by a light source or by bad weather
conditions, such as heavy rain, fog,
snow, etc.
• The surrounding is either too dark or
too bright.
5-80
05
•
Outside air temperature is hot or cold.
Reverse Parking Collision-Avoidance
•
The wind is either strong (over
Assist system may alert the driver or
apply brake power unnecessarily under
20 km/h (12 mph)) or blowing
perpendicular to the rear bumper.
the following conditions even if there are
"no" pedestrians or objects.
•
Objects generating excessive
noise, such as vehicle horns, loud
•
Any non-factory equipment or
accessories have been installed.
motorcycle engines, or truck air
brakes, are near the vehicle.
•
The condition of the vehicle is
unstable due to an accident or other
•
An ultrasonic sensor with a similar
frequency is near the vehicle.
causes.
•
The height of the bumper or the
•
There is ground height difference
sensor installation has been modified.
between the vehicle and the
pedestrian.
•
The bumper height has changed due
to heavy loads, tire pressure change,
•
The image of the pedestrian in the
rear view camera is indistinguishable
etc.
from the background.
•
The rear view camera or the ultrasonic
•
The pedestrian is near the rear edge of
sensor(s) is stained with foreign
matter, such as snow, dirt, etc.
the vehicle.
•
The pattern on the road is mistaken
•
The pedestrian is not standing upright.
for a pedestrian.
•
The pedestrian is either too short or
•
There is a shadow or a light reflecting
too tall for the system to recognize.
on the ground.
•
The pedestrian is wearing clothes that
•
Pedestrians or objects are around the
are hard for the system to recognize.
path of the vehicle.
•
The pedestrian is wearing a cloth that
•
Objects generating excessive
does not reflect ultrasound well.
noise, such as vehicle horns, loud
•
The size, thickness, height, or shape of
motorcycle engines, or truck air
the object does not reflect ultrasound
brakes, are near the vehicle.
well (e.g., pole, bush, curbs, carts,
edge of a wall, etc.).
•
The vehicle is backing towards a
narrow passage or parking space.
•
The pedestrian or the object is
moving.
•
The vehicle is backing towards an
uneven road surface, such as unpaved
•
The pedestrian or the object is very
road, gravel, bump, gradient, etc.
close to the rear of the vehicle.
•
A trailer is attached to the vehicle.
•
A wall is behind the pedestrian or the
object.
•
The object is not at the rear center of
the vehicle.
•
The plane of the obstacle is not
parallel to the rear bumper.
•
The road is slippery or inclined.
•
The driver backs up the vehicle
immediately after shifting to R
(Reverse).
•
The driver accelerates or turns the
vehicle.
5-81
Convenience Features
reverSe pArKinG DiSTAnce wArninG (pDw)
(if eQUippeD)
Operation of Reverse Parking
Distance Warning System
Operating condition
•
This system will activate when
backing up with the ignition switch in
the ON position. However, if vehicle
speed exceeds 5 km/h (3 mph), the
system may not detect objects.
•
If vehicle speed exceeds 10km/h (6
mph), the system will not warn you
ODN8A059056
even though objects are detected.
[A] : Rear Sensor
•
When more than two objects are
Reverse Parking Distance Warning
sensed at the same time, the closest
system assists the driver during reverse
one will be recognized first.
movement of the vehicle by chiming if
an object is sensed within the distance of
120 cm (48 in) behind the vehicle.
This system is a supplemental system
that senses objects within the range and
location of the sensors, it cannot detect
objects in other areas where sensors are
not installed.
WARNING
• ALWAYS look around your vehicle to
make sure there are not any objects
or obstacles before moving the
vehicle in any direction to prevent a
collision.
• Always pay close attention when the
vehicle is driven close to objects,
particularly pedestrians, and
especially children.
• Be aware that some objects may
not be visible on the screen or be
detected by the sensors, due to the
objects distance, size or material, all
of which can limit the effectiveness
of the sensor.
5-82
05
Types of warning sound and indicator
Types of warning sound
Indicator
When an object is 60 cm to 120 cm (24 in to 48 in) from the rear
bumper : Buzzer beeps intermittently.
When an object is 30 cm to 60 cm (12 in to 24 in) from the rear
bumper : Buzzer beeps more frequently.
When an object is within 30 cm (12 in) of the rear bumper :
Buzzer beeps continuously.
NOTICE
• The indicator may differ from the illustration depending on objects or sensors
status. If the indicator blinks, have the vehicle inspected by an authorized
HYUNDAI dealer.
• If the audible warning does not sound or if the buzzer sounds intermittently when
shifting into R (Reverse) position, this may indicate a malfunction with Reverse
Parking Distance Warning system. If this occurs, have the vehicle inspected by an
authorized HYUNDAI dealer.
5-83
Convenience Features
To Turn off Reverse Parking
Non-Operational Conditions
Distance Warning System
of Reverse Parking Distance
(if equipped)
Warning System
Reverse Parking Distance Warning
system may not operate normally when:
• Moisture is frozen to the sensor.
• Sensor is covered with foreign matter,
such as snow or water, or the sensor
cover is blocked.
There is a possibility of Reverse
Parking Distance Warning system
malfunction when:
ODN8059057L
• Driving on uneven road surfaces such
as unpaved roads, gravel, bumps, or
Push the button to turn off Reverse
gradient.
Parking Distance Warning system. The
indicator light on the button will turn on.
• Objects generating excessive
noise such as vehicle horns, loud
motorcycle engines, or truck air
brakes can interfere with the sensor.
• Heavy rain or water spray is present.
• Wireless transmitters or mobile
phones are present near the sensor.
• The sensor is covered with snow.
• Any non-factory equipment or
accessories have been installed, or if
the vehicle bumper height or sensor
installation has been modified.
Detecting range may decrease
when:
• Outside air temperature is extremely
hot or cold.
5-84
05
The following objects may not be
Reverse Parking Distance
recognized by the sensor:
Warning System Precautions
• Sharp or slim objects such as ropes,
•
Reverse Parking Distance Warning
chains or small poles.
system may not sound consistently
• Objects, which tend to absorb sensor
depending on the speed and shapes
frequency such as clothes, spongy
of the objects detected.
material or snow.
•
Reverse Parking Distance Warning
• Undetectable objects smaller than 100
system may malfunction if the vehicle
cm (40 in) and narrower than 14 cm (6
bumper height or sensor installation
in) in diameter.
has been modified or damaged. Any
non-factory installed equipment or
accessories may also interfere with
WARNING
the sensor performance.
Your new vehicle warranty does not
•
The sensor may not recognize objects
cover any accidents or damage to the
less than 30 cm (12 in) from the
vehicle or injuries to its occupants
sensor, or it may sense an incorrect
related to Reverse Parking Distance
distance. Use caution.
Warning system. Always drive safely
•
When the sensor is frozen or stained
and cautiously.
with snow, dirt, or water, the sensor
may be inoperative until the stains are
removed using a soft cloth.
•
Do not push, scratch or strike the
sensor with any hard objects that
could damage the surface of the
sensor. Sensor damage could occur.
•
Do not spray the sensors or its
surrounding area directly with a high
pressure washer. Shock applied from
high pressure water may cause the
device to not operate normally.
5-85
Convenience Features
forwArD/reverSe pArKinG DiSTAnce wArninG (pDw)
(if eQUippeD)
WARNING
• ALWAYS look around your vehicle
to make sure there are no objects or
obstacles before moving the vehicle
in any direction to prevent a collision.
• Always pay close attention when the
vehicle is driven close to objects,
particularly pedestrians, and
especially children.
• Be aware that some objects may
ODN8A059055
not be visible on the screen or be
detected by the sensors, due to the
objects distance, size or material, all
of which can limit the effectiveness
of the sensor.
• Do not tamper with the location
or size of the license plate
discretionally.
ODN8059056L
[A] : Front sensor, [B] : Rear sensor
Forward/Reverse Parking Distance
Warning system assists the driver during
movement of the vehicle by chiming if
an object is sensed within the distance of
100 cm (40 in) in front and 120 cm (48 in)
behind the vehicle.
This system is a supplemental system
that senses objects within the range and
location of the sensors, it cannot detect
objects in other areas where sensors are
not installed.
5-86
05
Operation of Forward/Reverse
• If ‘Parking Distance Warning Auto On’
is set from the cluster or infotainment
Parking Distance Warning
system setup menu, the system will
System
not turn off even if vehicle speed
Operating condition
exceeds 20 km/h (12 mph, Non RSPA
and PCA) / 30 km/h (24 mph, Applied
RSPA or PCA). Also if vehicle speed
belows 10 km/h (6 mph) will resume
warning when objects are detected.
ODN8059057
• This system will activate when
Forward/Reverse Parking Distance
Warning system button is pressed
with the engine running.
• Forward/Reverse Parking Distance
Warning system button turns on
automatically and activates Forward/
Reverse Parking Distance Warning
system when you press the R(Reverse)
button. However, if vehicle speed
exceeds 10 km/h (6 mph), the system
will not warn you even though objects
are detected, and if vehicle speed
exceeds 20 km/h (12 mph), the system
will turn off automatically. To turn on
the system, press Forward/Reverse
Parking Distance Warning system
button.
• When more than two objects are
sensed at the same time, the closest
one will be recognized first.
5-87
Convenience Features
Warning indicator
Distance from object
When driving
When driving
Warning sound
cm (in)
forward
rearward
60 ~ 100
Buzzer beeps
Front
-
(24 ~ 40)
intermittently
60 ~ 120
Buzzer beeps
Rear
-
(24 ~ 48)
intermittently
Buzzer beeps
Front
frequently
30 ~ 60
(12 ~ 24)
Buzzer beeps
Rear
-
frequently
Buzzer sounds
Front
continuously
~ 30
(~ 12)
Buzzer sounds
Rear
-
continuously
NOTICE
• The indicator may differ from the illustration depending on objects or sensors
status. If the indicator blinks, have the vehicle inspected by an authorized
HYUNDAI dealer.
• If the audible warning does not sound or if the buzzer sounds intermittently when
shifting into R (Reverse) position, this may indicate a malfunction with Forward/
Reverse Parking Distance Warning system. If this occurs, have the vehicle
inspected by an authorized HYUNDAI dealer.
5-88
05
Non-Operational Conditions
Detecting range may decrease
of Forward/Reverse Parking
when:
Distance Warning System
• Outside air temperature is extremely
Forward/Reverse Parking Distance
hot or cold.
Warning system may not operate
normally when:
The following objects may not be
recognized by the sensor:
• Moisture is frozen to the sensor.
• Sharp or slim objects such as ropes,
• Sensor is covered with foreign matter,
chains or small poles.
such as snow or water, or the sensor
cover is blocked.
• Objects, which tend to absorb sensor
frequency such as clothes, spongy
material or snow.
There is a possibility of Forward/
Reverse Parking Distance Warning
• Undetectable objects smaller than 100
system malfunction when:
cm (40 in) and narrower than 14 cm (6
in) in diameter.
• Driving on uneven road surfaces such
as unpaved roads, gravel, bumps, or
gradient.
WARNING
• Objects generating excessive
Your new vehicle warranty does not
noise such as vehicle horns, loud
cover any accidents or damage to the
motorcycle engines, or truck air
vehicle or injuries to its occupants
brakes can interfere with the sensor.
related to Forward/Reverse Parking
• Heavy rain or water spray is present.
Distance Warning system. Always drive
• Wireless transmitters or mobile
safely and cautiously.
phones are present near the sensor.
• The sensor is covered with snow.
• Any non-factory equipment or
accessories have been installed, or if
the vehicle bumper height or sensor
installation has been modified.
5-89
Convenience Features
Forward/Reverse Parking
Distance Warning System
Precautions
•
Forward/Reverse Parking Distance
Warning system may not sound
consistently depending on the speed
and shapes of the objects detected.
•
Forward/Reverse Parking Distance
Warning system may malfunction if
the vehicle bumper height or sensor
installation has been modified or
damaged. Any non-factory installed
equipment or accessories may also
interfere with the sensor performance.
•
The sensor may not recognize objects
less than 30 cm (12 in) from the
sensor, or it may sense an incorrect
distance. Use caution.
•
When the sensor is frozen or stained
with snow, dirt, or water, the sensor
may be inoperative until the stains are
removed using a soft cloth.
•
Do not push, scratch or strike the
sensor. Sensor damage could occur.
•
Do not spray the sensors or its
surrounding area directly with a high
pressure washer. Shock applied from
high pressure water may cause the
device to not operate normally.
5-90
05
remoTe SmArT pArKinG ASSiST (rSpA) (if eQUippeD)
Remote Smart Parking Assist system
WARNING
helps drivers recognize surrounding
objects by using sensors to detect
•
Remote Smart Parking Assist system
parking spaces control the steering
may not operate normally if the
wheel, shift the gear and adjust vehicle
vehicle needs wheel alignment
speed automatically.
adjustment. Have the vehicle
checked by an authorized HYUNDAI
Remote moving forward and backward
dealer.
function provides assistance for forward
and backward movement as well as
•
If you use a different tire or
taking the vehicle out of the parking
wheel size rather than the size
space with driver outside the vehicle.
recommended by the HYUNDAI
dealer, Remote Smart Parking Assist
The driver should check the distance
system may not work properly.
between the parking space and the
Always use the same size tire and
objects in direct and be careful to
wheel.
operate.
•
Do not use Remote Smart Parking
Due to the surrounding environment and
Assist system when under the
array or shape of the parked vehicles, the
influence of alcohol or drugs.
vehicle may not be parked or exit at the
exact spot you have wished.
•
Remote Smart Parking Assist system
may not operate properly depending
on the surrounding environment and
à RSPA stands for Remote Smart
other conditions.
Parking Assist.
•
Remote Smart Parking Assist system
Remote Smart Parking
may not recognize the object too
Assist system button
close to the vehicle.
Parking Distance Warning
•
When operating Remote Smart
system button
Parking Assist system, be careful
of the objects such as flower pots
or parking blocks located above
Function
or below the sensor position. Such
object may damage the vehicle or
Remote Moving
other objects.
Forward/
Available
Backward
•
Remote Smart Parking Assist system
should only be considered as a
supplementary function. The driver
Deactivate Remote Smart Parking
must check the front and rear view
Assist system and park/exit your vehicle
for objects. The operational function
manually if it is necessary. While using
of the system can be affected by
Remote Smart Parking Assist system,
many factors and conditions of the
Parking Distance Warning system
surroundings, so the responsibility
activates as well. Remote Smart Parking
rests always with the driver.
Assist system will be cancelled if Parking
•
Do not let children or other person to
Distance Warning system is cancelled by
use the smart key.
pressing the button to the OFF position.
For operation of Parking Distance
Warning system, refer to the relevant
description in this manual.
5-91
Convenience Features
Operating Condition
Non-operating Condition
In the following conditions, Remote
Smart Parking Assist system may not
operate properly or cancelled. Drive the
vehicle manually in the below conditions.
•
Curved or diagonal parking space
•
An obstacle such as a trash can,
bicycle, motorcycle, shopping cart,
narrow pillar etc. is near
•
Near a circular pillar or narrow pillar,
or a pillar surrounded by objects such
as fire extinguisher, etc.
ODN8059072
•
Heavy snow, rain or wind
Use Remote Smart Parking
Assist system when all the below
•
Bumpy roads
conditions are met
•
A vehicle equipped with a snow chain
• When the parking space is a straight
or spare tire
line
•
Tire pressure lower or higher than the
• When there is enough space to move
standard tire pressure
or exit the vehicle
•
Slippery or uneven road
•
A vehicle loaded with longer or wider
cargo compared to the vehicle or a
trailer connected to the vehicle
•
The sensor is positioned incorrectly by
an impact to the bumper
•
Inclined roads parking
•
A problem with the wheel alignment
•
Vehicle leaned severely to one side
•
Front or rear distance sensors are
malfunction or not working properly.
(Refer to Parking Distance Warning
system in this chapter)
•
Low battery level of the smart key that
requires battery replacement.
5-92
05
Limitations of the system
2. Parking in snow
• When the vehicle has been parked/
stopped for a long time in a cold
environment, the Remote Moving
Forward/Backward may be delayed
depending on the vehicle condition
when the vehicle is turned on
remotely.
• Remote Smart Parking Assist system
may suddenly apply brake to avoid
collision against stationary or moving
object.
ODN8A059264
• The performance of the system may
be degraded and frequently stop
Snow may interfere with sensor
when driving in strong electric field
operation or Remote Smart Parking
area.
Assist system may cancel if the road is
slippery while parking.
• When there is any obstacle within
the blind-spot area, drive out of the
parking space manually
3. Parking diagonal
• Remote Smart Parking Assist system
may not recognize the object that
appears suddenly.
WARNING
Do not use Remote Smart Parking Assist
system in the following conditions for
unexpected results may occur and
cause a serious accident.
ODN8059080
1. Parking on inclines
Remote Smart Parking Assist system is
not a supplemental for diagonal parking.
Even if the vehicle is able to enter the
space, do not operate the system.
ODN8A059269
Park and exit manually when you park on
inclines.
5-93
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст