| | | ------------------------------------------------------------------------------------------------------------------------------------------------------------- 05 WINDOWS OCN7N050002N (1) Driver’s door power window switch (5) Window opening and closing (2) Front passenger’s door power (6) Automatic power window window switch (7) Power window lock switch (3) Rear door (left) power window switch (4) Rear door (right) power window switch 5-51 ------------------------------------------------------------------------------------------------------------------------------------------------------------- Convenience Features Power Windows Window opening and closing The ignition switch must be in the ON position to be able to raise or lower the windows. Each door has a Power Window switch to control that door’s window. The driver has a Power Window Lock switch which can block the operation of passenger windows. The power windows will operate for approximately 30 seconds after the ignition switch is placed in the ACC or LOCK/OFF position. However, if the front doors are opened, the Power Windows OCN7050082 will not operate even within the 30 To open: second period. Press the window switch down to the first detent position (5). Release the WARNING switch when you want the window to stop. To avoid serious injury or death, do not extend your head, arms or body outside the windows while driving. To close: Pull the window switch up to the first detent position (5). Release the window Information switch when you want the window to ś In cold and wet climates, power stop. windows may not work properly due to freezing conditions. Auto down window (if equipped) ś While driving with the rear windows Pressing the power window switch down or with the sunroof (if equipped) down momentarily to the second opened (or partially opened), your detent position (6) completely lowers vehicle may demonstrate a wind the window even when the switch is buffeting or pulsation noise. This released. To stop the window at the noise is normal and can be reduced desired position while the window is in or eliminated by taking the following operation, pull up or press down and actions. If the noise occurs with one release the switch. or both of the rear windows down, partially lower both front windows Auto up/down window (if equipped) approximately one inch. If you Pressing or pulling up the power window experience the noise with the sunroof switch momentarily to the second open, slightly close the sunroof. detent position (6) completely lowers or lifts the window even when the switch is released. To stop the window at the desired position while the window is in operation, pull up or press down and release the switch. 5-52 ------------------------------------------------------------------------------------------------------------------------------------------------------------- 05 To reset the power windows Automatic reverse (if equipped) If the power windows do not operate normally, the automatic power window system must be reset as follows: 1. Place the ignition switch to the ON position. 2. Close the window and continue pulling up on the power window switch for at least one second. If the power windows do not operate properly after resetting, have the system checked by an authorized HYUNDAI OCN7050026 dealer. If a window senses any obstacle while it is closing automatically, it will stop and WARNING lower approximately 12 inches (30 cm) to allow the object to be cleared. The automatic reverse feature doesn’t activate while resetting the power If the window detects the resistance window system. Make sure body parts while the power window switch is or other objects are safely out of the pulled up continuously, the window way before closing the windows to will stop upward movement then lower avoid injuries or vehicle damage. approximately 1 inch (2.5 cm). If the power window switch is pulled up continuously again within 5 seconds after the window is lowered by the automatic window reverse feature, the automatic window reverse will not operate. Information The automatic reverse feature is only active when the “Auto Up” feature is used by fully pulling up the switch to the second detent. WARNING Make sure body parts or other objects are safely out of the way before closing the windows to avoid injuries or vehicle damage. Objects less than 0.16 inch (4 mm) in diameter caught between the window glass and the upper window channel may not be detected by the automatic reverse window and the window will not stop and reverse direction. 5-53 ------------------------------------------------------------------------------------------------------------------------------------------------------------- Convenience Features NOTICE WARNING Do not install any accessories on the ś NEVER leave the keys in your vehicle windows. The automatic reverse with unsupervised children, when feature may not operate. the engine is running. ś NEVER leave any child unattended in Power window lock switch the vehicle. Even very young children may inadvertently cause the vehicle to move, entangle themselve s in the windows, or otherwise injure themselves or others. ś Always double check to make sure arms, hands, head and other obstructions are safely out of the way before closing a window. ś Do not allow children to play with the power windows. Keep the driver’s door power window lock switch in OCN7050027 the LOCK position (pressed). Serious The driver can disable the power window injury can result from unintentional switches on the rear passenger doors by window operation by the child. pressing the power window lock switch. ś Do not extend your head, arms or When the power window lock switch is body outside the windows while pressed: driving. ś The rear passenger control will not be able to operate the rear passenger power window ś Note that the front passenger control is still able to operate the front passenger window, and that the driver master control can still operate all the power windows. NOTICE ś To prevent possible damage to the power window system, do not open or close two windows or more at the same time. This will also ensure the longevity of the fuse. ś Never try to operate the main switch on the driver’s door and the individual door window switch in opposite directions at the same time. If this is done, the window will stop and cannot be opened or closed. 5-54 ------------------------------------------------------------------------------------------------------------------------------------------------------------- 05 681522) ǣ,) (48,33('Ǥ If your vehicle is equipped with a Sunshade sunroof, you can slide or tilt your sunroof with the sunroof switch located on the overhead console. OCN7050029 Use the sunshade to block direct sunlight coming through the sunroof glass. OCN7050028 Open or close the sunshade by hand. The sunroof can only be operated when the ignition switch or Engine Start/Stop button is in the ON or START position. Information The sunroof can be operated for The sunshade opens automatically when approximately 3 minutes after the the sunroof glass is opened, but the ignition switch or Engine Start/Stop sunshade does not close automatically button is in the ACC or LOCK/OFF when the sunroof glass is closed. Also, only position. the sunshade cannot be closed when the sunroof glass is opened. WARNING NOTICE ś Adjust the sunroof or sunshade when your vehicle stops. This could result Do not pull the sunshade up or down, in loss of control and an accident or apply excessive force as such action that may cause injury, or property may damage the sunshade or cause it damage. to malfunction. ś Do not leave the engine running and the key in your vehicle with unsupervised children. Unattended children could operate the sunroof, which could result in serious injury. ś Do not sit on the top of the vehicle. It may cause injury or vehicle damage. NOTICE Do not operate the sunroof when roof bars are installed on the vehicle or when there is luggage on the roof. 5-55 ------------------------------------------------------------------------------------------------------------------------------------------------------------- Convenience Features Tilt Open/Close Slide Open/Close OCN7051144 OCN7N051031 [1]: Tilt open ś Push the sunroof switch rearward, [2]: Tilt close the sunshade and sunroof glass slide open. ś Push the sunroof switch upward, the sunroof glass tilts open. Push the sunroof switch forward, only the sunroof glass closes. ś Push the sunroof switch forward when the sunroof glass is tilt opened, the ś Push the sunroof switch forward or sunroof glass closes. rearward to the first detent position, the sunroof glass moves until the switch is released. The sunroof glass tilts open or closes while the switch is pushed. ś Push the sunroof switch forward or rearward to the second detent position, the sunroof glass operates Information automatically (auto slide feature). To The sunroof glass cannot slide open and stop the sunroof movement at any tilt open at the same time. You cannot tilt point, push the sunroof switch in any the sunroof glass open while the sunroof direction. glass is slide open. Also, you cannot slide ś The sunroof glass stops halfway the sunroof glass open while the sunroof (first detent position) before it is fully is tilt open. Slide open or tilt open the opened. To fully open the sunroof sunroof glass when the sunroof glass is glass, push the sunroof switch completely closed. rearward once more. At this time, the sunroof glass opens only while the switch is pushed. Information To reduce wind noise while driving, have you drive at the recommended position (first detent position) before the maximum slide open position. 5-56 ------------------------------------------------------------------------------------------------------------------------------------------------------------- 05 Automatic Reversal (if equipped) NOTICE ś Do not continue to push the sunroof switch after the sunroof is fully opened, closed, or tilted. Damage to the sunroof motor could occur. ś Continuous operations such as slide open/close, tilt open/close, etc. may cause the motor or sunroof system to malfunction. ś Regularly remove any accumulated dust on the sunroof rail. ś Dust accumulated between the ODH043039 sunroof and roof panel can make If the sunroof glass senses any obstacle noise. Open the sunroof and remove while it is closing automatically, it will dust regularly using a clean cloth. reverse direction then stop at a certain ś Do not try to open the sunroof when position. the temperature is below freezing The auto reverse function may not or when the sunroof is covered work if an object thin or soft is caught with snow or ice. The sunroof may between the sliding sunroof glass and not work properly and may break if sunroof sash. opened by force. ś Do not open or drive with the sunroof WARNING glass open immediately after rain or washing the vehicle. Water may wet ś Make sure heads, hands, arms or the interior of the vehicle. any other body parts or objects are out of the way before operating the ś Do not extend any luggage outside the sunroof while driving. Vehicle sunroof. Body parts or objects may get caught causing injuries or vehicle damage may occur if the vehicle suddenly stops. damage. ś Never deliberately use your body parts to test the automatic reversal WARNING function. The sunroof glass may Do not extend your head, arms, body reverse direction, but there is a risk parts or objects outside the sunroof of injury. while driving. Injuries may occur if the vehicle suddenly stops. 5-57 ------------------------------------------------------------------------------------------------------------------------------------------------------------- Convenience Features Resetting the Sunroof Information If the sunroof is not reset when the vehicle battery is disconnected or discharged, or the sunroof fuse is blown, the sunroof may not operate normally. Sunroof Open Warning (if equipped) OCN7051028L In some circumstances resetting the sunroof operation may need to be performed. Some instances where resetting the sunroof may be required include: ś When the 12-volt battery is either disconnected or discharged OCN7040018 ś When the sunroof fuse is replaced If the driver turns off the engine when ś If the sunroof one-touch AUTO OPEN/ the sunroof is not fully closed, the CLOSE operation is not functioning warning chime will sound for several properly seconds and the sunroof open warning will appear on the cluster LCD display. Sunroof resetting procedure: Close the sunroof securely when leaving 1. It is recommended to perform the your vehicle. reset procedure with the vehicle engine running. Start the vehicle in P CAUTION (Park). 2. Make sure the sunroof glass is in the Make sure the sunroof is closed fully fully closed position. If the sunroof when leaving your vehicle. glass is open, push the switch forward If the sunroof is left open, rain or snow until the sunroof glass is fully closed. may wet the interior of the vehicle. 3. Release the switch when the sunroof Also, leaving the sunroof open when the glass is fully closed. vehicle is unattended may invite theft. 4. Push the switch forward until the sunroof glass moves slightly. Then release the switch. 5. Once again push and hold the sunroof switch forward until the sunroof glass slides open and close. Do not release the switch until the operation is completed. If you release the switch during operation, start the procedure again from step 2. 5-58 ------------------------------------------------------------------------------------------------------------------------------------------------------------- 05 HOOD Opening the hood OCN7050035 OCN7050033 5. Hold the hood open with the support rod (3). 1. Park the vehicle and set the parking brake. 2. Pull the release lever to unlatch the WARNING hood. The hood should pop open Support rod slightly. ś After driving, the engine compartment and support rod will be hot. Grasp the support rod in the area wrapped in rubber to prevent burns. ś The support rod must be inserted completely into the hole provided whenever you inspect the engine compartment. This will prevent the hood from falling and possibly injuring you. OCN7050034 3. Go to the front of the vehicle, raise the hood slightly, push the secondary latch up (1) inside of the hood center and lift the hood (2). 4. Pull out the support rod. 5-59 ------------------------------------------------------------------------------------------------------------------------------------------------------------- Convenience Features Closing the hood WARNING 1. Before closing the hood, check the ś Before closing the hood, ensure following: all obstructions are removed from ś All filler caps in engine around the hood opening. compartment must be correctly ś Always double check to be sure that installed. the hood is firmly latched before ś Gloves, rags or any other driving away. Check there is no combustible material must hood open warning light or message be removed from the engine displayed on the instrument cluster. compartment. Driving with the hood opened may 2. Return the support rod to its clip to cause a total loss of visibility, which prevent it from rattling. might result in an accident. 3. Lower the hood halfway (lifted ś Do not move the vehicle with the approximately 30 cm from the closed hood in the raised position, as vision position) and push down to securely is obstructed, which might result in lock in place. Then double check to be an accident, and the hood could fall sure the hood is secure. or be damaged. If the hood can be raised slightly, it is not securely locked. Open it again and close it with more force. 5-60 ------------------------------------------------------------------------------------------------------------------------------------------------------------- 05 TRUNK Opening the trunk Inside 1. Make sure the shift lever is in P (Park, for Dual clutch transmission/ Intelligent variable transmission) or first gear or R (Reverse, for manual transmission) and set the parking brake. Outside OCN7050037 - Use the trunk release lever. 3. Lift the trunk lid up. Closing the trunk Lower the trunk lid and press down until it locks. To be sure the trunk lid is OCN7050036 securely fastened, always check by trying 2. Then do one of the following: to pull it up again. ś Hold down the trunk unlock button located on your remote key or smart WARNING key for more than 1 second. Always keep the trunk lid completely ś Additionally, for vehicles equipped closed while the vehicle is in motion. If with smart key : it is left open or ajar, poisonous exhaust - While all doors are unlocked, press gases containing carbon monoxide the switch in the trunk to open the (CO) may enter the vehicle and serious trunk with or without the smart key illness or death may result. in your possession. - If any door is locked or all doors are Information locked, the switch can still be used to open the trunk, as long as the To prevent damage to the trunk lift smart key is in your possession. cylinders and the attached hardware, always close the trunk before driving. NOTICE In cold and wet climates, trunk lock and trunk mechanisms may not work properly due to freezing conditions. 5-61 ------------------------------------------------------------------------------------------------------------------------------------------------------------- Convenience Features Emergency Trunk Safety Release WARNING ś You and your passengers must be aware of the location of the Emergency Trunk Safety Release lever in this vehicle and how to open the trunk in case you are accidentally locked in the trunk. ś NEVER allow anyone to occupy the trunk of the vehicle at any time. If the trunk is partially or totally latched and the person is unable to get out, serious injury or death could occur OCN7050038 due to lack of ventilation, exhaust Your vehicle is equipped with an fumes and rapid heat build-up, or Emergency Trunk Safety Release lever because of exposure to cold weather located inside the trunk. When someone conditions. The trunk is also a highly is inadvertently locked in the trunk, the dangerous location in the event of a trunk can be opened by moving the lever crash because it is not a protected in the direction of the arrow and pushing occupant space but is a part of the the trunk open. vehicle’s crush zone. ś Your vehicle should be kept locked and the Smart Key should be kept out of the reach of children. Parents should teach their children about the dangers of playing in trunks. ś Use the release lever for emergencies only. 5-62 ------------------------------------------------------------------------------------------------------------------------------------------------------------- 05 Smart Trunk Release 1. Setting (if equipped) To activate the Smart Trunk release, go to User Settings Mode and select Smart Trunk on the LCD display. For more details, refer to “LCD Display” in this chapter. If your vehicle is equipped with additional navigation, please refer to the infotainment system manual separately supplied. OCN7050041L On a vehicle equipped with a smart key, the trunk can be opened using the Smart Trunk release system. How to use the Smart Trunk release The trunk can be opened with no touch activation satisfying all the conditions OCN7050040N below. 2. Detect and Alert ś After 15 seconds when all doors are If you are positioned in the detecting closed and locked area (20 ~ 40 inches behind the vehicle) ś Positioned in the detecting area for carrying a smart key, the hazard warning more than 3 seconds lights will blink and chime will sound to alert you the smart key has been detected and the trunk will open. Information The Smart Trunk release does not operate when: Information ś The smart key is detected within 15 Do not approach the detecting area if you seconds after the doors are closed and do not want the trunk to open. If you have locked, and is continuously detected. unintentionally entered the detecting area and the hazard warning lights and chime ś The smart key is detected within 15 starts to operate, leave the detecting area seconds after the doors are closed and with the smart key. The trunk will stay locked, and 1.5 m from the front door closed. handles. (for vehicles equipped with Welcome Light) ś A door is not locked or closed. ś The smart key is in the vehicle. 5-63 ------------------------------------------------------------------------------------------------------------------------------------------------------------- Convenience Features How to deactivate the Smart Trunk release function using the smart key Type A OCN7050041L 3. Automatic opening The hazard warning lights will blink and OCN7050004 chime will sound 6 times and then the Type B trunk will open. WARNING ś Make sure you close the trunk before driving your vehicle. ś Make sure there are no people or objects around the trunk before opening or closing the trunk. ś Make sure objects in the trunk do not OCN7050005 come out when opening the trunk on a slope. It may cause serious injury. 1. Door lock ś Make sure to deactivate the Smart 2. Door unlock Trunk when washing your vehicle. 3. Trunk open Otherwise, the trunk may open 4. Panic inadvertently. 5. Remote Start (if equipped) ś The key should be kept out of reach of children. Children may inadvertently open the Smart Trunk If you press any button of the smart key release while playing around the rear during the Detect and Alert stage, the area of the vehicle. Smart Trunk release function will be deactivated. Make sure to be aware of how to deactivate the Smart Trunk release function for emergency situations. 5-64 ------------------------------------------------------------------------------------------------------------------------------------------------------------- 05 Detecting area Information ś If you press the door unlock button (2), the Smart Trunk release function will be deactivated temporarily. But, if you do not open any door for 30 seconds, the smart trunk function will be activated again. ś If you press the trunk open button (3) for more than 1 second, the trunk opens. ś If you press the door lock button (1) or trunk open button (3) when the Smart Trunk release function is not in the OCN7050040N Detect and Alert stage, the smart trunk ś The Smart Trunk release operates with function will not be deactivated. a welcome alert if the smart key is ś In case you have deactivated the Smart detected within 20 ~ 40 inches from Trunk function by pressing the smart the trunk. key button and opened a door, the ś The alert stops at once if the smart Smart Trunk release function can be key is positioned outside the activated again by closing and locking detecting area during the Detect and all doors. Alert stage. Information ś The Smart Trunk release function will not work if any of the following occurs: - The smart key is close to a radio transmitter such as a radio station or an airport which can interfere with normal operation of the transmitter. - The smart key is near a mobile two way radio system or a cellular phone. - Another vehicle’s smart key is being operated close to your vehicle. ś The detecting range may decrease or increase when : - One side of the tire is raised to replace a tire or to inspect the vehicle. - The vehicle is slantingly parked on a slope or unpaved road, etc. 5-65 ------------------------------------------------------------------------------------------------------------------------------------------------------------- Convenience Features FUEL FILLER DOOR Opening the fuel filler door Information If the fuel filler door does not open because ice has formed around it, tap lightly or push on the door to break the ice and release the door. Do not pry on the door. If necessary, spray around the door with an approved de-icer fluid (do not use radiator anti-freeze) or move the vehicle to a warm place and allow the ice to melt. Closing the fuel filler door 1. To install the fuel tank cap, turn it OCN7050042 clockwise until it “Clicks”. The fuel filler door must be opened from 2. Close the fuel filler door until it is inside the vehicle by pulling up the fuel latched securely. filler door opener. 1. Turn the engine off. 2. Pull up the fuel filler door opener. WARNING Gasoline is highly flammable and explosive. Failure to follow these guidelines may result in SERIOUS INJURY or DEATH: ś Read and follow all warnings posted at the gas station. ś Before refueling, note the location of the Emergency Gasoline Shut-Off, if available, at the gas station. ś Before touching the fuel nozzle, you should eliminate the potential build- OCN7050043 up of static electricity by touching 3. Pull the fuel filler door (1) out to fully a metal part of the vehicle, a safe open. distance away from the fuel filler 4. To remove the fuel tank cap (2), turn neck, nozzle, or other gas source, it counterclockwise. You may hear a with your bare hand. hissing noise as the pressure inside ś Do not use cellular phones while the tank equalizes. refueling. Electric current and/or 5. Place the cap on the fuel filler door. electronic interference from cellular phones can potentially ignite fuel vapors and cause a fire. Information Open and close the reservoir cap by using the handle on the cap cover for safety. 5-66 ------------------------------------------------------------------------------------------------------------------------------------------------------------- 05 ś Do not get back into a vehicle ś Do not over-fill or top-off your once you have begun refueling. vehicle tank, which can cause You can generate a build-up of gasoline spillage. static electricity by touching, ś If a fire breaks out during refueling, rubbing or sliding against any item leave the vicinity of the vehicle, and or fabric capable of producing immediately contact the manager static electricity. Static electricity of the gas station and then contact discharge can ignite fuel vapors the local fire department. Follow any causing a fire. If you must re-enter safety instructions they provide. the vehicle, you should once again ś If pressurized fuel sprays out, it can eliminate potentially dangerous cover your clothes or skin and thus static electricity discharge by subject you to the risk of fire and touching a metal part of the vehicle, burns. Always remove the fuel cap away from the fuel filler neck, nozzle carefully and slowly. If the cap is or other gasoline source, with your venting fuel or if you hear a hissing bare hand. sound, wait until the condition stops ś When refueling, always move the before completely removing the cap. shift lever to the P (Park) position, ś Always check that the fuel cap is set the parking brake, and place the installed securely to prevent fuel ignition switch to the LOCK/OFF spillage in the event of an accident. position. ś Sparks produced by electrical components related to the engine Information can ignite fuel vapors causing a fire. Make sure to refuel your vehicle according ś When using an approved portable to the “Fuel Requirements” suggested in fuel container, be sure to place the the Introduction chapter. container on the ground prior to refueling. Static electricity discharge NOTICE from the container can ignite fuel vapors causing a fire. Once refueling ś Do not spill fuel on the exterior has begun, contact between your surfaces of the vehicle. Any type of bare hand and the vehicle should fuel spilled on painted surfaces may be maintained until the filling is damage the paint. complete. ś If the fuel filler cap requires ś Use only approved portable plastic replacement, use only a genuine fuel containers designed to carry and HYUNDAI cap or the equivalent store gasoline. specified for your vehicle. An ś Do not use matches or a lighter and incorrect fuel filler cap can result in a serious malfunction of the fuel do not smoke or leave a lit cigarette in your vehicle while at a gas station, system or emission control system. especially during refueling. 5-67 ------------------------------------------------------------------------------------------------------------------------------------------------------------- Convenience Features EXTERIOR LIGHTS Lighting Control To operate the lights, turn the knob at the end of the control lever to one of the following positions: OCN7050055 AUTO headlight The parking lamp and headlight will be turned ON or OFF automatically depending on the amount of daylight as ODN8A059200 measured by the ambient light sensor on 1. OFF the center dash (1). 2. AUTO headlight Even with the AUTO headlight feature 3. Parking lamp in operation, it is recommended to manually turn ON the headlights when 4. Headlight driving at night or in a fog, driving in the rain, or when you enter dark areas, such Daytime running light (DRL) as tunnels and parking facilities. The Daytime Running Lights (DRL) can make it easier for others to see the front of your vehicle during the day, especially NOTICE after dawn and before sunset. ś Do not cover or spill anything on the sensor (1) located in front of the The DRL system will turn the dedicated instrument panel. lamp OFF when: ś Do not clean the sensor using ś The headlights are ON. a window cleaner, the cleanser may leave a light film which could ś The parking lamps are ON. interfere with sensor operation. ś The vehicle is turned off. ś If your vehicle window tint or other ś The parking brake is engaged. types of metallic coating on the front windshield, the AUTO headlight system may not work properly. 5-68 ------------------------------------------------------------------------------------------------------------------------------------------------------------- 05 High Beam Operation ODN8A059202 Parking lamp ( ) ODN8A059205 The parking lamp, license plate lamp and To turn on the high beam headlight, push instrument panel lamp are turned ON. the lever away from you. The lever will return to its original position. The high beam indicator will light when the headlight high beams are switched on. To turn off the high beam headlight, pull the lever towards you. The low beams will turn on. WARNING Do not use high beam when there are ODN8A059203 other vehicles approaching you. Using Headlight ( ) high beam could obstruct the other driver’s vision. The headlight, parking lamp, license plate lamp and instrument panel lamp are turned ON. Information The ignition switch must be in the ON position to turn on the headlight. 5-69 ------------------------------------------------------------------------------------------------------------------------------------------------------------- Convenience Features Turn Signals And Lane Change Signals ODN8A059204 To flash the high beam headlight, pull the lever towards you, then release the lever. ODN8A059207 The high beams will remain ON as long as you hold the lever towards you. To signal a turn, push down on the lever for a left turn or up for a right turn in position (A). To signal a lane change, move the turn signal lever slightly and hold it in position (B). The lever will return to the OFF position when released or when the turn is completed. If an indicator stays on and does not flash or if it flashes abnormally, one of the turn signal bulbs may be burned out and will require replacement. One touch turn signal function To activate a one-touch turn signal function, move the turn signal lever slightly and then release it. The lane change signals will blink 3, 5 or 7 times. You can activate or deactivate the One Touch Turn Signal function or choose the number of blinks (3, 5, or 7) from the User Settings Mode on the LCD display. For more details, refer to “LCD Display Modes” in chapter 4. If your vehicle is equipped with additional navigation, please refer to the infotainment system manual separately supplied. 5-70 ------------------------------------------------------------------------------------------------------------------------------------------------------------- 05 Battery Saver Function Headlight Delay Function The purpose of this feature is to (if equipped) help prevent the battery from being If you place the ignition switch in the discharged. The system automatically ACC or OFF position with the headlights turns off the parking lamp when the ON, the headlights (and/or parking driver turns the vehicle off and opens the lamps) remain on for about 5 minutes. driver-side door. However, with the engine off if the With this feature, the parking lamps will driver’s door is opened and closed, the turn off automatically if the driver parks headlights (and/or parking lamps) are on the side of road at night. turned off after 15 seconds. However, the position lamps stay ON The headlights (and/or parking lamps) even when the driver-side door is opened can be turned off by pressing the lock if the headlight switch is turned to the button on the remote key or smart key position lamp or AUTO (if equipped) twice or turning the light switch to the position after the engine is turned off. OFF or AUTO position. However, if you turn the light switch to the AUTO position If necessary, to keep the lamps on when it is dark outside, the headlights turn the position lamps OFF and ON will not be turned off. again using the headlight switch on the steering column after the engine is You can activate or deactivate the turned off. headlight Delay function from the User Settings Mode in the LCD display. For more details, refer to “LCD Display Modes” in chapter 4. If your vehicle is equipped with additional navigation, please refer to the infotainment system manual separately supplied. NOTICE If the driver exits the vehicle through another door besides the driver door, the battery saver function does not operate and the headlight delay function does not turn OFF automatically. This may cause the battery to discharge. To avoid battery discharge, turn OFF the headlights manually from the headlight switch before exiting the vehicle. 5-71 ------------------------------------------------------------------------------------------------------------------------------------------------------------- Convenience Features +,*+ %($0 $66,67 ǣ+%$Ǥ ǣ,) (48,33('Ǥ NOTICE ś Always keep the front view camera in good condition to maintain optimal performance of High Beam Assist. ś For more details on the precautions of the front view camera, refer to “Forward Collision-Avoidance Assist (FCA)” section in chapter 7. High Beam Assist Settings OCN7050141N :LWK WKH HQJLQH RQ VHOHFW œ/LJKWV Ɵ +LJK High Beam Assist will automatically Beam Assist’ from the Settings menu to adjust the headlight range (switches turn on High Beam Assist and deselect to between high beam and low beam) turn off the system. depending on the brightness of detected vehicles and certain road conditions. WARNING Detecting Sensor For your safety, change the Settings after parking the vehicle at a safe location. OCN7061030L [1] : Front view camera The front view camera is used as a detecting sensor to help detect ambient light and brightness while driving. Refer to the picture above for the detailed location of the detecting sensor. 5-72 ------------------------------------------------------------------------------------------------------------------------------------------------------------- 05 High Beam Assist Operation ś When High Beam Assist is operating, high beam switches to low beam if Display and control any of the following conditions occur: ś After selecting ‘High Beam Assist’ - When the headlight of an oncoming in the Settings menu, High Beam vehicle is detected. Assist will operate by following the procedure below. - When the tail lamp of a vehicle in front is detected. - Place the headlight switch in the AUTO position and push - When the headlight or tail lamp of a the headlight lever towards the motorcycle or a bicycle is detected. instrument cluster. The High Beam - When the surrounding ambient light Assist ( ) indicator light will is bright enough that high beams illuminate on the cluster and High are not required. Beam Assist will be enabled. - When streetlights or other lights are - When High Beam Assist is enabled, detected. high beam will turn on when vehicle speed is above 25 mph (40 km/h). High Beam Assist Malfunction When vehicle speed is below 15 and Limitations mph (25 km/h), high beam will turn High Beam Assist malfunction off. - The High Beam ( ) indicator light will illuminate on the cluster when high beam is on. ś When High Beam Assist is operating, if the headlight lever or switch is used, High Beam Assist operates as follow: - If the headlight lever is pulled towards you when the high beam is off, the high beam will turn on without High Beam Assist canceled. When you let go of the headlight OTM050218L lever, the lever will move to the When High Beam Assist is not working middle and the high beam will turn properly, the ‘Check High Beam Assist off. (HBA) system’ warning message - If the headlight lever is pulled will appear and warning light will towards you when the high beam is illuminate on the cluster. Have the on by High Beam Assist, low beam vehicle inspected by an authorized will turn on and High Beam Assist HYUNDAI dealer. will turn off. - If the headlight switch is placed from AUTO to another position (headlight/position/off), High Beam Assist will turn off and the corresponding lamp will turn on. 5-73 ------------------------------------------------------------------------------------------------------------------------------------------------------------- Convenience Features Limitations of High Beam Assist WARNING High Beam Assist may not work properly ś At times, High Beam Assist may not in the following situations: work properly High Beam Assist is ś Light from an oncoming or front for your convenience only. It is the vehicle is not detected because of responsibility of the driver for safe lamp damage, or because it is hidden driving practices and always check from sight, etc. the road conditions for your safety. ś Headlight of an oncoming or front ś When High Beam Assist does not vehicle is covered with dust, snow or operate properly, change the water. headlight position manually between ś A front vehicle’s headlights are off, but high beam and low beam. the fog lamps are on, etc. ś There is a lamp that has a similar shape as a vehicle’s lamp. ś Headlights have been damaged or not repaired properly. ś Headlights are not aimed properly. ś Driving on a narrow-curved road, rough road, uphill or downhill. ś Vehicle in front is partially visible on a crossroad or curved road. ś There is a traffic light, reflecting sign, flashing sign or mirror ahead. ś There is a temporary reflector or flash ahead (construction area). ś The road conditions are bad such as being wet, iced or covered with snow. ś A vehicle suddenly appears from a curve. ś The vehicle is tilted from a flat tire or is being towed. ś Light from an oncoming or front vehicle is not detected due to obstacles in the air such as exhaust fume, smoke, fog, snow, or water spay or blizzard on the road, or fogging in the lamp, etc. Information For more details on the limitations of the front view camera, refer to “Forward Collision-Avoidance Assist (FCA)” section in chapter 7. 5-74 ------------------------------------------------------------------------------------------------------------------------------------------------------------- 05 INTERIOR LIGHTS Front Lamps WARNING Do not use the interior lights when driving in the dark. The interior lights may obscure your view and cause an accident. NOTICE Do not use the interior lights for extended periods when the vehicle is turned off or the battery will discharge. OCN7050056 Interior Lamp AUTO Cut (1) Front Map Lamp The interior lamps will automatically go off approximately 20 minutes after the (2) Front Door Lamp engine is turned off and the doors are (3) Front Room Lamp ON closed. If a door is opened, the lamp (4) Front Room Lamp OFF will go off 40 minutes after the engine is turned off. If the doors are locked by the remote key or smart key and the vehicle Front map lamp: enters the armed stage of the theft Press either of these lens to turn the map alarm system, the lamps will go off five lamp on or off. This light produces a spot seconds later. beam for convenient use as a map lamp at night or as a personal lamp for the driver and the front passenger. 5-75 ------------------------------------------------------------------------------------------------------------------------------------------------------------- Convenience Features Front Door Lamp ( ): Mood Lamp (if equipped) The front or rear room lamps come on when the front or rear doors are opened if the engine is running or not. When doors are unlocked by the remote key or smart key, the front and rear lamps come on for approximately 30 seconds as long as any door is not opened. The front and rear room lamps go out gradually after approximately 30 seconds if the door is closed. However, if the ignition switch is in the ON position or all doors are locked, the front and rear lamps will turn off. If a OCN7C052041 door is opened with the ignition switch in 7KH ODPS WXUQV RQ ZKHQ œ8VHU VHWWLQJV Ɵ the ACC position or the OFF position, the /LJKWV Ɵ $PELHQW /LJKWŔ LV VHOHFWHG IURP front and rear lamps stay on for about 20 the infotainment system screen. minutes. Front room lamp Rear Lamp ś : Press the button to turn ON the room lamp for the front/rear seats. ś : Press the button to turn OFF the room lamp for the front/rear seats. OCN7050057 Rear Room Lamp ( ): Press this switch to turn the rear room lamp on and off. NOTICE Do not leave the lamp switches on for an extended period of time when the engine is turned off. 5-76 ------------------------------------------------------------------------------------------------------------------------------------------------------------- 05 Luggage Compartment Lamp Vanity Mirror Lamp (if equipped) OCN7050059 OCN7050058 The luggage compartment lamp comes Push the switch to turn the light on or off. on when the trunk is opened. ś : The lamp will turn on if this button is pressed. NOTICE ś : The lamp will turn off if this The luggage compartment lamp comes button is pressed. on as long as the trunk is open. To prevent unnecessary battery system NOTICE drain, close the trunk securely after Always have the switch in the off using the luggage compartment. position when the vanity mirror lamp is not in use. If the sunvisor is closed without the lamp off, it may discharge the battery or damage the sunvisor. 5-77 ------------------------------------------------------------------------------------------------------------------------------------------------------------- Convenience Features Welcome System (if equipped) You can activate or deactivate the Welcome Light from the User Settings Welcome light Mode on the LCD display. For more details, refer to “LCD Display” in chapter 4. If your vehicle is equipped with additional navigation, please refer to the infotainment system manual separately supplied. Interior lamp When the interior lamp switch is in the DOOR position and all doors (and trunk) are closed and locked, the room lamp will come on for 30 seconds if any of the OCN7050054 below is performed. Door handle lamp (if equipped) ś When the door unlock button is When all the doors (and trunk) are closed pressed on the remote key or smart and locked, the door handle lamp will key. come on for about 15 seconds if any of ś When the button of the outside door the below is performed. handle is pressed. ś When the door unlock button is At this time, if you press the door lock or pressed on the remote key or smart unlock button, the room lamp will turn key. off immediately. ś When the button of the outside door handle is pressed. ś When the vehicle is approached with the smart key in possession. Headlight and parking lamp When the headlight (lamp switch in the headlight or AUTO position) is on and all doors (and trunk) are locked and closed, the headlight and parking lamp will come on for 15 seconds if/or any of the below is performed. ś When the door unlock button is pressed on the remote key or smart key. At this time, if you press the door lock or unlock button, the headlight and parking lamp will turn off immediately. 5-78 ------------------------------------------------------------------------------------------------------------------------------------------------------------- 05 WIPERS AND WASHERS Windshield Wipers Operates as follows when the ignition switch is in the ON position. MIST: For a single wiping cycle, push the lever upward and release. The wipers will operate continuously if the lever is held in this position. OFF: Wiper is not in operation. INT: Wiper operates intermittently at the same wiping intervals. To vary OCN7050090N the speed setting, move the speed A. Wiper speed control control lever. The top most setting will run the wipers most frequently ś MIST - Single wipe (for more rain). The bottom setting ś OFF - Off will run the wipers the least ś INT / --- - Intermittent wipe frequently (for less rain). ś LO- Low wiper speed LO: The wiper runs at a lower speed. ś HI - High wiper speed HI: The wiper runs at a higher speed. B. Intermittent control wipe time adjustment Information C. Wash with brief wipes If there is heavy accumulation of snow (pull lever towards you) or ice on the windshield, defrost the windshield for about 10 minutes, or until the snow and/or ice is removed before using the windshield wipers to ensure proper operation. If you do not remove the snow and/or ice before using the wiper and washer, it may damage the wiper and washer system. 5-79 ------------------------------------------------------------------------------------------------------------------------------------------------------------- Convenience Features Windshield Washers NOTICE ś To prevent possible damage to the washer pump, do not operate the washer when the fluid reservoir is empty. ś To prevent possible damage to the wipers or windshield, do not operate the wipers when the windshield is dry. ś To prevent damage to the wiper arms and other components, do not attempt to move the wipers manually. ODN8059209K ś To prevent possible damage to the In the OFF position, pull the lever gently wipers and washer system, use anti- toward you to spray washer fluid on the freezing washer fluids in the winter windshield and to run the wipers 1-3 season or cold weather. cycles. The spray and wiper operation will continue until you release the lever. If the washer does not work, you may need to add washer fluid to the washer fluid reservoir. WARNING When the outside temperature is below freezing, ALWAYS warm the windshield using the defroster to help prevent the washer fluid from freezing on the windshield and obscuring your vision which could result in an accident and serious injury or death. 5-80 ------------------------------------------------------------------------------------------------------------------------------------------------------------- 05 0$18 $/ &/,0$7 ( &21752/ 6<67(0 ǣ,) (48,33('Ǥ Type A OCN7050100N Type B OCN7050101N 1. Fan speed control knob 2. Temperature control knob 3. Mode selection knob 4. Front windshield defroster position 5. Rear window defroster button 6. Air intake control button 7. A/C (Air conditioning) button 5-81 | |
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст