Hyundai Santa Fe (2006 year). Manual — part 9
MECHANICAL POWER STEERING SYSTEM
ST -33
12. Install the rack support yoke (A), rack supportspring
(B), yoke plug (C) and lock nut (D) in the ordershown
in the illustration.
Apply semi-drying sealantto the
threaded section of the yoke plug before installation.
D
C
B
A
APJF005L
13. With the rack placed in the center position, attach the
yoke plug to the rack housing. Tighten the yoke plug
to 12 Nm (120 kg·cm, 8.9 lb·ft), with a 14mm socket
(A). Loosen the yoke plug approximately from 30 to
60 and tighten the yoke nut to the specified torque.
Tightening Torque Nm(kgf·m, lb-ft) :
50 ~ 70(5 ~ 7, 37 ~ 52)
A
APHE007I
14. Tighten the feed tube (A) to the specified torque and
install the mounting rubber using adhesive.
A
APHE006H
15. Apply the specified grease to the bellows mounting
position (fitting groove) of the tie rod.
Recommended grease : Silicone grease
APGE008C
16. Install the new attaching band to the bellows.
NOTE
When the bellows are installed, a new band must be
used.
17. Install the bellows in position, taking care not to twist
it.
ST -34
STEERING SYSTEM
18. Fill the dust cover inner side and lip with the speci-
fied grease, and fix the dust cover in position with the
clipring attached in the groove of the tie rod end.
Recommended grease
A : POLY LUB GLY 801K or equivalent
B : SHOWA SUNLIGHT MB2 or equivalent
Dust cover inner side and lip : THREE BOND
A
B
EPKE043A
19. Install the tie rod end (B) to the tie rod (A).
B
A
KPBF202A
INSTALLATION
ECBE4BC2
1.
Installation is the reverse of removal.
NOTE
Be sure to connect between a tube and a hose as
shown in the illustration.
LPLG500J
2.
Add the power steering oil.
3.
After installation, bleed the power steering system.
(Refer to the air bleeding in ST group)
4.
Adjust the wheel alignment. (Refer to SS group)
MECHANICAL POWER STEERING SYSTEM
ST -35
POWER STEERING HOSES
COMPONENTS
E332082E
1. Power steering oil reservior
2. Suction hose
3. Power steering oil pump
4. Pressure tube
5. Power steering geat box
6. Return tube
7. Oil cooler (Gasoline only)
SCMST6511L
ST -36
STEERING SYSTEM
REMOVAL
E8F174D6
1.
Drain the power steering fluid by disconnecting return
hose (A).
A
SCMST6521D
2.
Disconnect the pressure tube (A) and suction hose
(B) from the power steering oil pump.
Tightening torque Nm (kgf.m, lb-ft):
55 ~ 65 (4.5 ~ 5.5, 40 ~ 47)
[DIESEL]
A
B
SCMST6538D
[GASOLINE]
A
B
SCMST6504L
3.
Disconnect the pressure tube (A) and return tube (B)
from the valve body housing.
Tightening torque Nm (kgf.m, lb-ft):
12 ~ 18 (1.2 ~ 1.8, 9 ~ 13)
A
B
SCMST6527D
4.
Loosen the pressure and return tube bracket bolts and
nut.
SCMST6528D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст