Hyundai Santa Fe (2006 year). Manual — part 189
LIGHTING SYSTEM
BE -217
OFF
Illumination
ON
2
6
3
9
5
10
7
8
Terminal
Position
SCMBE6461L
HAZARD LAMP RELAY
1.
Disconnect the negative (-) battery terminal.
2.
Disconnect the passenger compartment.
3.
Check for continuity between terminals. There should
be continuity between the No.2 of I/P-C and No.3 or
No.4 of I/P-E terminals when power and ground are
connected to the No.2 of I/P-C and No.6 of I/P-G ter-
minals.
4.
There should be no continuity between the No.2 of
I/P-C and No.3 or No.4 of I/P-E terminals when power
is disconnected to the No.2 of I/P-C and No.6 of I/P-G
terminals.
A
G
H
B
D
L
J
K
F
N
M
E
C
SCMBE6462D
I/P-C
(2)
I/P-E
(3 or 4)
I/P-G
(6)
I/P-C
(2)
+
Power off
Power on
Terminal
Position
SCMBE6463L
BE -218
BODY ELECTRICAL SYSTEM
RHEOSTAT
INSPECTION
E4E671BB
1.
Disconnect the negative (-) battery terminal.
2.
Remove the lower crash pad switch assembly (A) by
using the scraper and then disconnect the connec-
tors.
[LHD]
A
B
SCMBE6458L
[RHD]
A
B
SCMBE6458R
3.
Remove the rheostat (B) from lower crash pad switch
assembly.
4.
Check for intensity of new rheostat switch. If the light
intensity of the lamps changes smoothly without any
flickering when the rheostat is turned, it can be as-
sumed that the rheostat is normal.
LIGHTING SYSTEM
BE -219
FRONT FOG LAMPS
INSPECTION
E738DE84
FRONT FOG LAMP RELAY
1.
Pull out the front fog lamp (A) relay from the engine
compartment relay box.
2.
Check for continuity between terminals. There should
be continuity between the No.87 and No.30 terminals
when power and ground are connected to the No.85
and No.86 terminals.
3.
There should be no continuity between the No.87 and
No.30 terminals when power is disconnected.
30
85
86
87
87
85
30
86
Front fog lamp relay
SCMBE6464L
30
87
85
86
+
Disconnected
Connected
Terminal
Power
LTGE221B
REPLACEMENT
E5D0F606
1.
Disconnect the negative (-) battery terminal.
2.
Remove the front side cover screw.
3.
Remove the front fog lamp assembly (A) after loosen-
ing screws (4EA).
SCMBE6441D
4.
Installation is the reverse of removal.
BE -220
BODY ELECTRICAL SYSTEM
REAR FOG LAMPS
INSPECTION
E7D4CDB2
REAR FOG LAMP SWITCH
1.
Disconnect the negative (-) battery terminal.
2.
Remove the lower crash pad switch (A) from the side
crash pad cover by using the scraper and then dis-
connect the connectors.
3.
Remove the rear fog lamp (B) switch from lower crash
pad switch.
[LHD]
A
B
1
2
3
4
5
6
SCMBE6427L
[RHD]
A
A
B
1
2
3
4
5
6
SCMBE6427R
4.
Check for continuity between the terminals in each
switch position according to the table.
OFF
ON
2
5
1
4
3
Illumination
IND.
Terminal
Position
SCMBE6469L
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст