Hyundai Santa Fe (2006 year). Manual — part 786
REAR SUSPENSION SYSTEM
SS -51
INSTALLATION
E163969D
1.
Install the rear upper arm (B), then install the mount-
ing bolts (A) of the rear upper arm and the cross mem-
ber.
Tightening torque Nm (kgf-m, lb-ft) :
98.1~117.7 (10.0~12.0, 72.3~86.8)
A
B
SCMSS6014D
NOTE
After checking the distance(453±10mm(17.83
±0.39in)) between the wheel housing garnish (A) and
the hub assembly (B) as shown in the illustration,
tighten the mounting bolts and nuts of rear chassis
part with specified torque.
A
B
453 10 mm
SCMSS6528D
2.
Install the split pin (A) and the castle nut (B) to the rear
upper arm ball joint (C).
Tightening torque Nm (kgf-m, lb-ft) :
78.5~88.3 (8.0~9.0, 57.9~65.1)
A
B
C
SCMSS6521D
3.
Install the rear cross member.
4.
Support the rear cross member assembly (A) with the
jack.
A
SCMSS6010D
SS -52
SUSPENSION SYSTEM
5.
Install the rear cross member mounting bolts (A), nuts
(B) and plate (C).
Tightening torque Nm (kgf-m, lb-ft) :
Bolts(A) : 156.9~176.5 (16~18, 115.7~130.2)
Nuts(B) : 156.9~176.5 (16~18, 115.7~130.2)
A
C
SCMSS6012D
B
C
SCMSS6013D
6.
Install the rear cross member stay (A) and mounting
bolt (B) and nut (C).
Tightening torque Nm (kgf-m, lb-ft) :
Bolt(B) : 68.6~88.3 (7~9, 50.6~65.1)
Nut(C) : 68.6~88.3 (7~9, 50.6~65.1)
B
A
C
SCMSS6011D
7.
After matching a match mark (C) on the rubber cou-
pling (A) and rear differential companion (B), Install
the propeller shaft mounting bolts (D).
Tightening torque Nm (kgf-m, lb-ft) :
49.0~68.6 (5~7, 36.2~50.6)
A
D
C
B
SCMSS6518D
REAR SUSPENSION SYSTEM
SS -53
8.
Install the wheel speed sensor (A) and the parking
brake cable (B) to the rear axle carrier.
Tightening torque Nm (kgf-m, lb-ft) :
Wheel speed sensor (A) :
6.9~10.8 (0.7~1.1, 5.1~8.0)
A
B
SCMSS6517D
9.
Install the brake caliper (B), then tighten the brake
caliper mounting bolts (A).
Tightening torque Nm (kgf-m, lb-ft) :
63.7~73.5 (6.5~7.5, 47.0~54.2)
A
B
SCMSS6515D
10. Support the rear lower arm with a jack as shown in
the illustration.
SCMSS6526D
11. Install the rear shock absorber (A).
Tightening torque Nm (kgf-m, lb-ft) :
Bolt(B) : 137.3~156.9 (14~16, 101.3~115.7)
Nut(C) : 98.1~117.7 (10.0~12.0, 72.3~86.8)
A
C
B
SCMSS6527D
SS -54
SUSPENSION SYSTEM
12. Install the wheel and tire (A) to the rear hub (B).
Tightening torque Nm (kgf-m, lb-ft) :
88.3~107.9 (9~11, 65.1~79.6)
A
B
C
SCMSS6512D
CAUTION
Be careful not to damage the hub bolts (C) when
installing the rear wheel and tire (A).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст