Hyundai Santa Fe (2006 year). Manual — part 787
REAR SUSPENSION SYSTEM
SS -55
REAR LOWER ARM
COMPONENT
EBAFBDF9
1. Rear lower arm
2. Rear coil spring upper pad
3. Rear coil spring
4. Rear coil spring lower pad
TORQUE : Nm (kgf.m, lb-ft)
137.3~156.9
(14~16, 101.3~115.7)
137.3~156.9
(14~16, 101.3~115.7)
1
2
3
4
SCMSS6507L
SS -56
SUSPENSION SYSTEM
REMOVAL
E9AD5A7C
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely sup-
ported.
2.
Remove the rear wheel and tire (A) from the rear hub
(B).
A
B
C
SCMSS6512D
CAUTION
Be careful not to damage to the hub bolts (C) when
removing the rear wheel and tire (A).
3.
Remove the mounting bolt (B) of the rear lower arm
(A) and the rear carrier, while supporting the lower
arm (A) with a jack as shown in the illustration.
Loosen the mounting bolt (C) of the cross member
and the rear lower arm.
C
A
B
SCMSS6529D
4.
Remove the spring (A), the upper pad (B) and the
lower pad (C).
B
A
C
SCMSS6522D
5.
Remove the lower arm.
CAUTION
If the bush is excessive worn and damaged, re-
place the lower arm assembly.
INSPECTION
E852A9AA
REAR LOWER ARM
1.
Check the bushing for wear and deterioration.
2.
Check the rear lower arm for bending or breakage.
3.
Check the bolts for damage.
SPRING
1.
Check the spring for distortion, aging or damage.
2.
Check the spring upper pad and lower pad for aging
or damage.
REAR SUSPENSION SYSTEM
SS -57
INSTALLATION
EEF25C9F
1.
Pretighten the mounting bolt of the cross member and
the rear lower arm.
2.
Install the spring (A), the upper pad (B) and the lower
pad (C).
B
A
C
SCMSS6522D
3.
Install the mounting bolt (B) of the rear lower arm (A)
and the rear carrier with a specified torque, while sup-
porting the lower arm (A) with a jack as shown in
the illustration. Tighten the mounting bolt (C) of the
cross member and the rear lower arm with a speci-
fied torque.
Tightening torque Nm (kgf-m, lb-ft) :
Bolt(B) : 137.3~156.9 (14~16, 101.3~115.7)
Nut(C) : 137.3~156.9 (14~16, 101.3~115.7)
C
A
B
SCMSS6529D
NOTE
After checking the distance(453±10mm(17.83
±0.39in)) between the wheel housing garnish (A) and
the hub assembly (B) as shown in the illustration,
tighten the mounting bolts and nuts of rear chassis
part with specified torque.
A
B
453 10 mm
SCMSS6528D
4.
Install the wheel and tire (A) to the rear hub (B).
Tightening torque Nm (kgf-m, lb-ft) :
88.3~107.9 (9~11, 65.1~79.6)
A
B
C
SCMSS6512D
CAUTION
Be careful not to damage the hub bolts (C) when
installing the rear wheel and tire (A).
SS -58
SUSPENSION SYSTEM
REAR ASSIST ARM
COMPONENT
EBE5C437
1. Rear assist arm
TORQUE : Nm (kgf.m, lb-ft)
137.3~156.9
(14~16, 101.3~115.7)
98.1~117.7
(10~12, 72.3~86.8)
1
SCMSS6508L
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст