Hyundai Santa Fe (2006 year). Manual — part 103
ATA -170
AUTOMATIC TRANSAXLE (A5HF1)
OUTPUT SPEED SENSOR
DESCRIPTION
EE59F1CD
Sensor type
1.
Type : HALL SENSOR
2.
Output voltage : DC 12V
3.
Current consumption : 22mA (Max)
Function
1.
Output shaft speed sensor : Detect the output shaft rpm(T/F DRIVE
GEAR RPM) at the T/F drive gear
2.
Feedback control, clutch-clutch control, damper clutch control, shift range control,
incorrect ratio control and sensor trouble detection signal.
Connector
1
2
3
C243
1. Ground
2. Power source
3. Input
SCMAT6005L
<Inside structure>
BKGF012B
Item
Inspection item
Standard value
Air gap
Output shaft speed sensor
0.05in(1.3mm)
Sensor resistance
Output shaft speed sensor
Over 4 MΩ
HIGH
Over 4.8V
Output voltage
LOW
Below 0.8V
AUTOMATIC TRANSAXLE CONTROL SYSTEM
ATA -171
REMOVAL
E2D1DE7E
1.
Remove the battery terminal.
2.
Remove the battery and battery tray.
3.
Remove the air cleaner assembly. (see the automatic
transaxle- Removal/ installation procedures)
4.
Remove the output shaft speed sensor connector.
5.
Remove the output shaft speed sensor(A).
A
SCMAT6039D
INSTALLATION
EDDDA414
1.
Install the new O-ring to the output shaft speed sen-
sor.
2.
Remove the output shaft speed sensor.
TORQUE:
10~12Nm(1.0~1.2kgf.m, 7~8lb-ft)
CAUTION
While installing the output shaft speed sensor, do
not allow dust or other foreign particles to enter
the transaxle.
3.
Check the connector for dust, dirt, or oil, then connect
the connector securel.
4.
Installation is the reverse of removal.
ATA -172
AUTOMATIC TRANSAXLE (A5HF1)
TRANSAXLE OIL TEMPERATURE
SENSOR
DESCRIPTION
E7EEEEF5
Sensor type
1.
Type : Thermister
2.
Use available temperature :-40~160 C(-40~320 F)
Function and feature
1.
Detect the temperature of ATF through the thermistor which is exposed outside.
2.
When shifting the range, it is used as the oil pressure control information.
Connector
1
2
3
4
5
9
10
11
12
6
7
8
C209
3.UD Solenoid valve
4.2ND Solenoid valve
5.A/T battery
6.A/T battery
7.A/T battery
8.VF Solenoid valve ground
9.DCC Solenoid valve
10.RED Solenoid valve
11.LR Solenoid valve
12.OD Solenoid valve
SCMAT6006L
Temp.[ C( F)]
Resistance (KΩ )
Voltage (V)
Temp.[ C( F)]
Resistance (KΩ )
Voltage (V)
-40(-40)
140.5
4.447
80(176)
1.085
0.932
-20(-4)
47.95
4.207
100(212)
0.63
0.591
0(32)
18.6
3.725
120(248)
0.385
0.381
20(68)
8.05
2.996
140(284)
0.25
0.255
40(104)
3.85
2.176
160(320)
0.16
0.166
60(140)
1.975
1.453
AUTOMATIC TRANSAXLE CONTROL SYSTEM
ATA -173
REMOVAL
E7B2DE5B
1.
Remove the battery terminal.
2.
Lift the vehicle.
3.
Remove the splash shield.
4.
Loosen the drain plug and drain the transaxle oil.
5.
Remove the valve body cover.
6.
Disconnect the oil temperature sensor connector and
remove the sensor(A) from the valve body.
A
SCMAT6042D
INSTALLATION
E8C2FBA3
1.
Install the oil temperature sensor(A) and connect the
sensor connector.
CAUTION
When connecting the oil temperature connector,
check the connector for rust, dirt, or oil, then re-
connect it.
A
SCMAT6042D
2.
Continue to apply liquid gasket at application points
at the valve body cover with Ø0.098in(2.5mm) thick-
ness.
Liquid gasket Part name : Threebond 1281B
SCMAT6052D
3.
Tighten the mounting bolt with the specified torque
after installing the valve body cover.
TORQUE:
10~12Nm(1.0~1.2kgf.m, 7~8lb-ft)
4.
Install the drain plug.
TORQUE :
35~45Nm(3.5~4.5kgf.m, 25~32lb-ft)
5.
Installation is the reverse of the removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст