Hyundai Santa Fe (2006 year). Manual — part 102
ATA -166
AUTOMATIC TRANSAXLE (A5HF1)
REMOVAL
EEEA3EC8
1.
Remove the battery terminal.
2.
Lift the vehicle.
3.
Remove the splash shield.
4.
Loosen the drain plug and drain the transaxle oil.
5.
Remove the valve body cover.
6.
Remove the VFS reservoir(A).
A
SCMAT6034D
7.
Disconnect the VFS solenoid valve connector.
8.
Remove the solenoid valve assembly(A).
A
KKCF009D
INSTALLATION
E31C8972
1.
Install the solenoid valve(A).
CAUTION
Apply the ATF oil or White Vaseline to the O-ring
not to be damaged.
A
KKCF009D
2.
Connect the solenoid valve connector to the valve
body.
CAUTION
When connecting the solenoid valve connector,
check the connector for rust, dirt, or oil, then re-
connect it.
3.
Install the VFS reservoir(A).
A
SCMAT6034D
AUTOMATIC TRANSAXLE CONTROL SYSTEM
ATA -167
4.
Continue to apply liquid gasket at application points
at the valve body cover with Ø2.5mm (0.098in) thick-
ness.
Liquid gasket Part name : Threebond 1281B
SCMAT6052D
5.
Tighten the mounting bolt with the specified torque
after installing the valve body cover.
TORQUE :
10~12Nm(1.0~1.2kgf.m, 7~8lb-ft)
6.
Install the drain plug and refill the transaxle fluid.
TORQUE :
35~45Nm(3.5~4.5kgf.m, 25~32lb-ft)
7.
Install the splash shield.
8.
Lower the vehicle and install the battery terminal.
ATA -168
AUTOMATIC TRANSAXLE (A5HF1)
INPUT SPEED SENSOR
DESCRIPTION
EBD4BF9F
Sensor type
1.
Type : HALL SENSOR
2.
Operating voltage : DC 12V
3.
Current consumption : 22mA (Max)
Function
1.
Input shaft speed sensor: Detect the input shaft rotation at the OD & REV
retainer side to control oil pressure when shifting.
2.
Feedback control, clutch-clutch control, damper clutch control, shift range control,
incorrect ratio control and sensor trouble detection signal.
Connector
1. Ground
2. Power source
3. Input
1
2
3
C242
SCMAT6004L
<Inside structure>
BKGF012B
Item
Inspection item
Standard value
Air gap
Input shaft speed sensor
0.05in(1.3mm)
Sensor resistance
Input shaft speed sensor
Over 4 MΩ
HIGH
Over 4.8V
Output voltage
LOW
Below 0.8V
AUTOMATIC TRANSAXLE CONTROL SYSTEM
ATA -169
REMOVAL
EED7E4CB
1.
Remove the battery terminal.
2.
Remove the battery and battery tray.
3.
Remove the air cleaner assembly. (see the automatic
transaxle-Removal/ installation procedures)
4.
Remove the input shaft speed sensor connector.
5.
Remove the input shaft speed sensor(A).
A
SCMAT6037D
INSTALLATION
EE7CFF15
1.
Install the new O-ring to the input shaft speed sensor.
2.
Install the input shaft speed sensor.
TORQUE:
10~12Nm(1.0~1.2kgf.m, 7~8lb-ft)
CAUTION
While installing the input shaft speed sensor, do
not allow dust or other foreign particles to enter
the transaxle.
3.
Check the connector for dust, dirt, or oil, and then
connect the connector securely.
4.
Installation is the reverse of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст