Chrysler PT Cruiser. Manual — part 74
Symptom:
*RKE INOPERATIVE
POSSIBLE CAUSES
TEST TRANSMITTER WITH TESTER
RKE TRANSMITTER NOT PROGRAMMED
TEST RKE TRANSMITTER
RKE TRANSMITTER - INOPERATIVE
RKE MODULE
RKE MODULE - RECEIVER INOPERABLE
TEST
ACTION
APPLICABILITY
1
NOTE: Ensure the RKE module is configured for RKE and the M1 (IOD) fuse
is installed.
Note: Ensure the voltage of each battery is greater than 3.0 volts before
proceeding.
Do you have access to the Miller Tool
99001 RF DETECTOR9? ?
All
Yes
→ Go To 2
No
→ Go To 4
2
Using the 9001 RF Detector, follow the instructions on the back of the tester and test
the transmitter several times.
Does the signal strength measure
9STRONG9?
All
Yes
→ Go To 3
No
→ Replace the transmitter.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition on
Place transmission in the Park position.
Ensure Vehicle Theft Security System (if equipped) is in Disarm Mode.
With the DRBIII
t, select Theft Alarm, VTSS, MISCELLANEOUS, then PROGRAM
RKE. Follow the instructions on the screen.
Exit PROGRAM RKE.
Activate the Door Locks using the RKE Transmitter.
Did the door locks respond properly to the RKE transmitter commands?
All
Yes
→ Repair complete.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Remote Keyless Entry Module and reprogram all
transmitters used with this vehicle.
Perform BODY VERIFICATION TEST - VER 1.
283
POWER DOOR LOCKS/RKE
TEST
ACTION
APPLICABILITY
4
Using the DRBIII select Theft Alarm, VTSS, MISCELLANEOUS then RKE FOB &
Module Test. Follow the instructions on the DRBIII screen.
Try the Door Locks using the original Transmitter.
Did the Door Locks respond properly to the Transmitter commands ?
All
Yes
→ Using the DRBIII, program the transmitter and recheck the
system. If okay, program all Transmitters that will be used with
this vehicle.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 5
5
Secure a known good Transmitter from another PL or PT vehicle.
Using the DRBIII select BODY, Theft Alarm, VTSS, MISCELLANEOUS then RKE
FOB & Module Test. Follow the instructions on the DRBIII screen.
Try the Door Locks using the Transmitter.
Did the Door Locks respond properly to the Transmitter commands ?
All
Yes
→ Replace the original Transmitter. Program all Transmitters that
will be used with this Vehicle.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Remote Keyless Entry Module.
Perform BODY VERIFICATION TEST - VER 1.
284
POWER DOOR LOCKS/RKE
*RKE INOPERATIVE —
Continued
Symptom:
AMBIENT TEMP MESSAGE NOT RECEIVED
When Monitored and Set Condition:
AMBIENT TEMP MESSAGE NOT RECEIVED
When Monitored:
Whenever the module is awake.
Set Condition:
When the module looks for ambient temperature messages and they are
not received, this code will set.
POSSIBLE CAUSES
TROUBLE CODE PRESENT
ENGINE TROUBLE CODE PRESENT
MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, record and erase DTC’s.
Cycle the ignition switch from On to Off.
Start the engine.
Run the engine at approximately 1500 RPM for 1 minute.
With the DRBIII
t, read DTCs.
Does the DRBIII
t display AMBIENT TEMP MESSAGES NOT RECEIVED?
All
Yes
→ Go To 2
No
→ The conditions that caused this code to set is not present at this
time. Using Service Information, check the charging system.
Perform BODY VERIFICATION TEST - VER 1.
2
Start the engine.
Run the engine at approximately 1500 RPM for 1 minute.
With the DRBIII
t, read ENGINE DTCs.
Does the DRBIII
t display any AMBIENT TEMP SENSOR DTC’s?
All
Yes
→ Refer to symptom Ambient Temp Sensor DTC’s in the Driveability
- NGC category.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Window Regulator Module in accordance with the
Service Information..
Perform BODY VERIFICATION TEST - VER 1.
285
POWER TOP
Symptom:
POWER TOP RELAY CONTROL CIRCUIT OPEN
When Monitored and Set Condition:
POWER TOP RELAY CONTROL CIRCUIT OPEN
When Monitored:
Whenever the module is awake.
Set Condition:
If the Driver Window Regulator Module does not sense any (0.0) voltage
on either the Top Down or Top Up Relay Control circuit, this code will set.
POSSIBLE CAUSES
TROUBLE CODE PRESENT
POWER TOP FUSE OPEN
RELAY FUSED B+ CIRCUIT OPEN
TOP DOWN RELAY CONTROL WIRE SHORT TO GROUND
TOP UP RELAY CONTROL WIRE SHORT TO GROUND
TOP DOWN RELAY CONTROL WIRE SHORT TO VOLTAGE
TOP UP RELAY CONTROL WIRE SHORT TO VOLTAGE
TOP DOWN RELAY CONTROL WIRE OPEN
TOP DOWN RELAY OPEN
TOP UP RELAY CONTROL WIRE OPEN
TOP UP RELAY OPEN
DRIVER WINDOW MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, record and erase DTC’s.
Cycle the ignition switch from On to Off.
Operate the Power Top down and up.
Wait one minute.
With the DRBIII
t, read DTCs.
Does the DRBIII
t display POWER TOP RELAY CONTROL CIRCUIT OPEN/
SHORTED?
All
Yes
→ Go To 2
No
→ The conditions that caused this code to set is not present at this
time. Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors for a intermittent condition.
Perform BODY VERIFICATION TEST - VER 1.
286
POWER TOP
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст