Chrysler PT Cruiser. Manual — part 936
(4) Place rubber bumper in position and press
down to seat the bumper.
(5) Install seat into vehicle. (Refer to 23 - BODY/
SEATS/SEAT - INSTALLATION).
REAR SEAT BACK COVER/
FOAM
REMOVAL
REMOVAL
(1) Remove seat from vehicle.
(2) Remove head restraint.
(3) Remove rear seat back.
(4) Disengage the J-strap retainer.
(5) Roll cover upward to hog rings. Cut hog rings
to free cover.
(6) Roll cover to top of seat back and remove head
restraint sleeve guides.
(7) Remove cover from seat back.
REMOVAL
(1) Remove seat from vehicle. (Refer to 23 - BODY/
SEATS/REAR SEAT - REMOVAL).
(2) Remove rear seat back. (Refer to 23 - BODY/
SEATS/REAR SEAT BACK - INSTALLATION).
(3) Disengage the J-strap retainer (Fig. 217) and
(Fig. 218).
Fig. 216 REAR SEAT CUSHION SHIELD 2
1 - ATTACHING SCREWS
Fig. 217 REAR SEAT BACK J-STRAP
Fig. 218 REAR SEAT BACK COVER
1 - J-STRAP
23 - 202
SEATS
PT
REAR SEAT BACK (Continued)
(4) Roll flap back to access push pin fasteners (Fig.
219).
(5) Raise back flap to release the hook and loop to
access the J-strap and hog rings. Release J-strap and
cut the hog rings (Fig. 220).
(6) Disconnect the lower J-strap from the rod (Fig.
221).
(7) Disconnect the upper J-strap from the rod (Fig.
222).
(8) Roll cover upward to hog rings. Cut hog rings
to free cover (Fig. 223).
Fig. 219 REAR SEAT BACK COVER
1 - PUSH PIN FASTENERS
Fig. 220 REAR SEAT BACK COVER
1 - J-STRAP
2 - HOOK AND LOOP
3 - HOG RINGS
Fig. 221 J-STRAP ON THE ROD
Fig. 222 J-STRAP ON UPPER ROD
Fig. 223 REAR SEAT BACK COVER
1 - HOG RINGS
PT
SEATS
23 - 203
REAR SEAT BACK COVER/FOAM (Continued)
(9) Roll seat cover bottom to clear the foam (Fig.
224).
(10) Roll seat back cover to the hog rings. Cut hog
rings (Fig. 225) and (Fig. 226)
(11) Pull back panel free of the seat cover and
foam (Fig. 227) and (Fig. 228).
Fig. 224 REAR SEAT BACK COVER
Fig. 225 REAR SEAT BACK COVER
1 - HOG RINGS
Fig. 226 REAR SEAT BACK COVER
1 - HOG RINGS
Fig. 227 REMOVE BACK PANEL
1 - BACK PANEL
2 - FOAM
23 - 204
SEATS
PT
REAR SEAT BACK COVER/FOAM (Continued)
(12) Remove seat back cover from the foam (Fig.
229).
INSTALLATION
INSTALLATION
(1) Position cover at the top of seat back.
(2) Carefully roll cover down to the area that hog
rings are to be installed.
(3) Install hog rings.
(4) Roll cover downward.
(5) Engage the J-strap retainer
(6) Install new head restraint sleeve guides.
(7) Install seat back to seat cushion. Tighten bolts
to 40 N·m (30 ft. lbs.) torque.
(8) Install seat in vehicle.
(9) Install head restraint.
(10) Check seat back and headrest operation.
INSTALLATION - PT-27 ONLY
(1) Place seat back panel on to the foam. Roll seat
cover onto the back panel and foam (Fig. 230) and
(Fig. 231).
Fig. 228 REAR SEAT BACK PANEL
Fig. 229 REAR SEAT BACK COVER
1 - HOOK AND LOOP
2 - HOG RINGS
Fig. 230 REAR SEAT BACK PANEL
Fig. 231 REMOVE BACK PANEL
1 - BACK PANEL
2 - FOAM
PT
SEATS
23 - 205
REAR SEAT BACK COVER/FOAM (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст