Chrysler PT Cruiser. Manual — part 937
(2) Pull seat back cover down into position and
install the hog rings (Fig. 232), (Fig. 233), and (Fig.
234).
(3) Pull seat cover down and around the bottom of
the seat back (Fig. 235).
Fig. 232 REAR SEAT BACK COVER
1 - HOOK AND LOOP
2 - HOG RINGS
Fig. 233 REAR SEAT BACK COVER
1 - HOG RINGS
Fig. 234 REAR SEAT BACK COVER
1 - HOG RINGS
Fig. 235 REAR SEAT BACK COVER
23 - 206
SEATS
PT
REAR SEAT BACK COVER/FOAM (Continued)
(4) Roll cover upward to hog rings. Cut hog rings
to free cover (Fig. 236).
(5) Connect the J-strap to the upper rod (Fig. 237).
(6) Connect the J-strap to the from lower rod (Fig.
238).
(7) Connect the J-strap and install hog rings (Fig.
239).
Fig. 236 REAR SEAT BACK COVER
1 - HOG RINGS
Fig. 237 J-STRAP ON UPPER ROD
Fig. 238 J-STRAP ON LOWER ROD
Fig. 239 REAR SEAT BACK COVER
1 - J-STRAP
2 - HOOK AND LOOP
3 - HOG RINGS
PT
SEATS
23 - 207
REAR SEAT BACK COVER/FOAM (Continued)
(8) Install push pin fasteners. Pull seat back cover
down and smooth out any wrinkles (Fig. 240).
(9) Engage the J-strap retainer (Fig. 241) and (Fig.
242).
(10) Install rear seat back (Refer to 23 - BODY/
SEATS/REAR SEAT BACK - INSTALLATION).
(11) Install rear seat. (Refer to 23 - BODY/SEATS/
REAR SEAT - INSTALLATION).
REAR SEAT BACK CUSHION
COVER/FOAM - PT-27
REMOVAL - PT-27 ONLY
(1) Remove seat from vehicle. (Refer to 23 - BODY/
SEATS/REAR SEAT - REMOVAL).
(2) Remove seat back. (Refer to 23 - BODY/SEATS/
REAR SEAT BACK - REMOVAL).
(3) Disengage J-strap attaching seat cover from
the seat cushion frame.
(4) Pull cover off to the hog rings (Fig. 243).
(5) Cut hog rings attaching seat cover to seat cush-
ion pad.
(6) Remove seat cushion cover and foam from seat
cushion frame (Fig. 244).
Fig. 240 REAR SEAT BACK COVER
1 - PUSH PIN FASTENERS
Fig. 241 REAR SEAT BACK COVER
1 - J-STRAP
Fig. 242 REAR SEAT BACK J-STRAP
Fig. 243 REAR SEAT CUSHION FOAM
1 - HOOK AND LOOP
2 - HOG RINGS
23 - 208
SEATS
PT
REAR SEAT BACK COVER/FOAM (Continued)
INSTALLATION - PT-27 ONLY
(1) Place seat cushion cover and foam onto seat
cushion frame (Fig. 245).
(2) Pull cover into position to install hog rings
(Fig. 246).
(3) Engage J-strap attaching seat cover the seat
cushion.
(4) Install seat back. (Refer to 23 - BODY/SEATS/
REAR SEAT BACK - INSTALLATION).
(5) Install rear seat into vehicle. (Refer to 23 -
BODY/SEATS/REAR SEAT - INSTALLATION).
REAR SEAT BOLSTER - PT-27
REMOVAL
(1) Lower convertible top.
(2) Fold rear seats down and forward.
(3) Remove left rear seat belt lower anchor.
(4) Remove right rear seat belt lower anchor.
(5) Remove push pin fasteners attaching molding
upper seat belt to top well.
(6)
Remove two screws from front side upper bol-
ster assembly to rear seat back panel (Fig. 247).
(7) Remove two screws from the rear attaching
upper bolster assembly to rear seat back panel (Fig.
248).
(8) Remove both bezels at seat belt through holes
in headrest assembly.
(9) Fish right and left seat belt through bolster
assembly.
(10) Remove rear seat bolster from vehicle.
Fig. 244 REAR SEAT CUSHION FRAME
Fig. 245 REAR SEAT CUSHION FRAME
Fig. 246 REAR SEAT CUSHION FOAM
1 - HOOK AND LOOP
2 - HOG RINGS
PT
SEATS
23 - 209
REAR SEAT BACK CUSHION COVER/FOAM - PT-27 (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст