Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 681
(7) Install a hog ring at each hog ring locator to
hold upper horizontal seam wire to wire in seat back
foam.
(8) Install hog rings attaching seat cover seam
wires to seat frame.
(9) Pull seat cover over seat back frame and seat
back foam.
(10) Install hog rings at hog ring locators around
perimeter of seat back cushion attaching seat cover
to seat back frame.
(11) Install rear seat back to vehicle (Refer to 23 -
BODY/SEATS/REAR
SEAT
BACK
-
INSTALLA-
TION).
SEAT ADJUSTERS
REMOVAL
REMOVAL - FRONT SEAT ADJUSTER – POWER
(1) Remove front seat from vehicle.
(2) Remove seat cushion side shield and disconnect
switch connector.
(3) Remove seat back.
(4) Remove bolts attaching seat adjuster to cush-
ion pan (Fig. 33).
(5) Disconnect wire harness fasteners from cushion
pan.
(6) Remove seat adjuster from seat cushion.
REMOVAL - MANUAL ADJUSTER
(1) Remove front seat from vehicle (Refer to 23 -
BODY/SEATS/SEAT - REMOVAL).
(2) Remove recliner handle.
(3) Remove seat cushion side shield (Refer to 23 -
BODY/SEATS/SEAT CUSHION SIDE SHIELDS -
REMOVAL).
(4) Remove seat back (Refer to 23 - BODY/SEATS/
SEAT BACK - REMOVAL).
(5) Remove recliner.
(6) Remove towel bar spring.
(7) Remove push nuts attaching towel bar to seat
adjuster.
(8) Remove towel bar from seat adjuster.
(9) Remove seat adjuster.
INSTALLATION
INSTALLATION - FRONT SEAT ADJUSTER –
POWER
(1) Place seat adjuster in position on seat cushion
pan.
(2) Connect wire harness fasteners to the cushion
pan.
(3) Install bolts attaching seat adjuster to cushion
pad.
(4) Install seat back.
(5) Install bolt to attach seat back recliner to seat
back on each side of seat. Tighten bolt to 12 N·m (9
ft. lbs.) torque.
(6) Connect wire connectors and install the cush-
ion side shields.
(7) Install front seat in vehicle.
INSTALLATION - MANUAL ADJUSTER
(1) Place seat adjuster in position.
(2) Install seat adjuster.
(3) Install towel bar to seat adjuster.
(4) Install new push nuts to attach towel bar to
seat adjuster.
(5) Install towel bar spring.
(6) Install recliner.
(7) Install seat back (Refer to 23 - BODY/SEATS/
SEAT BACK - INSTALLATION).
(8) Install bolt to attach seat back recliner to seat
back on each side of seat. Tighten recliner bolt to 12
N·m (9 ft. lbs.) torque. Tighten pivot bolts to 40 N·m
(30 ft. lbs.) torque.
(9) Install recliner handle.
(10) Install front seat in vehicle (Refer to 23 -
BODY/SEATS/SEAT - INSTALLATION).
Fig. 33 Front Seat Track
1 - ATTACHING BOLTS
JR
SEATS
23 - 121
REAR SEAT BACK COVER (Continued)
SEAT BACK LATCH STRIKER
REMOVAL
(1) Release seat back latch and fold down.
(2) Remove the bolts and remove the latch striker
(Fig. 34).
INSTALLATION
NOTE: Striker is not symmetrical and should be
installed with the white date code towards the out-
side of the vehicle.
(1) Install the seat back striker and install the
bolts.
(2) Tighten the bolts to 12 N·m (9 ft. lbs.).
(3) Lock seat back in the up position and check for
operation.
SEAT BACK RECLINER
REMOVAL
REMOVAL
(1) Remove front seat from vehicle.
(2) Remove recliner handle
(3) Remove seat cushion side shield.
(4) Remove seat back.
(5) Remove manual recliner right and left bolts.
(6) Remove manual recliner assembly.
REMOVAL - JR-27 ONLY
(1) Remove seat from vehicle (Refer to 23 - BODY/
SEATS/SEAT - REMOVAL).
(2) Remove seat back from lower seat frame (Refer
to 23 - BODY/SEATS/SEAT BACK - REMOVAL).
(3) Remove upper recliner handle.
(4) Remove seat back cover until the screws
attaching the upper recliner mechanism to the seat
back frame can be accessed.
(5) Remove rubber bellows covering lower part of
seat back frame.
(6) Remove screws attaching upper recliner mech-
anism to seat frame.
(7) Remove bolts attaching recliner housing to seat
frame.
(8) Push upper recliner mechanism into seat frame
with handle shaft facing the front of the seat frame.
NOTE: Do not reuse bolts holding recliner housing
to seat frame. Verify availability prior to proceeding.
(9) Pull recliner housing and upper recliner handle
mechanism downward and out through bottom of
seat frame (Fig. 35).
INSTALLATION
INSTALLATION
(1) Place seat recliner in position.
(2) Install manual recliner right and left bolts.
(3) Install seat back.
(4) Install recliner.
(5) Install bolt to attach seat back recliner to seat
back on each side of seat. Tighten recliner bolt to 12
N·m (9 ft. lbs.) torque. Tighten pivot bolts to 40 N·m
(30 ft. lbs.) torque.
(6) Remove seat cushion side shield.
(7) Install recliner handle.
(8) Install front seat in vehicle.
Fig. 34 SEAT BACK STRIKER
1 - STRIKER
2 - BOLTS
Fig. 35 Recliner Housing
1 - UPPER RECLINER MECHANISM
2 - RECLINER HOUSING
3 - RECLINER CABLE
23 - 122
SEATS
JR
INSTALLATION - JR-27 ONLY
(1) Feed
upper
recliner
mechanism
and
then
recliner housing into the seat back frame with han-
dle shaft facing the front of the seat frame.
(2) Install new bolts to attach seat recliner hous-
ing to seat frame. Tighten to 34 N·m (300 in. lbs.)
torque.
(3) Pull upper recliner mechanism through hole in
seat frame.
(4) Install screws attaching upper recliner mecha-
nism to seat frame.
(5) Install rubber bellows covering lower part of
seat back frame.
(6) Install seat back cover.
(7) Install recliner spring bracket, spring, and lead
screw.
(8) Install seat back to lower seat frame (Refer to
23 - BODY/SEATS/SEAT BACK - INSTALLATION).
(9) Install recliner handle.
(10) Install seat into vehicle (Refer to 23 - BODY/
SEATS/SEAT - INSTALLATION).
JR
SEATS
23 - 123
SEAT BACK RECLINER (Continued)
STATIONARY GLASS
TABLE OF CONTENTS
page
page
WINDSHIELD
. . . . . . . . . . . . . . . . . . . . . . . . 124
. . . . . . . . . . . . . . . 124
. . . . . . . . . . . . . . . . . . . . . . . . . . 125
. . . . . . . . . . . . . . . . 126
. . . . . . . . . . . . . . . . . . . . . . 127
BACKLITE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
. . . . . . . . . . . . . . . . . . . . . . . . 129
WINDSHIELD
DESCRIPTION
The windshield is attached to the window frame
with urethane adhesive. The urethane adhesive is
applied cold and seals the surface area between the
window opening and the glass. The primer adheres
the urethane adhesive to the windshield.
It is difficult to salvage a windshield during the
removal operation. The windshield is part of the
structural support for the roof. The urethane bonding
used to secure the windshield to the fence is difficult
to cut or clean from any surface. If the moldings are
set in urethane, it would also be unlikely they could
be salvaged. Before removing the windshield, check
the availability of the windshield and moldings from
the parts supplier.
WARNING
WINDSHIELD SAFETY PRECAUTIONS
WARNING:
DO
NOT
OPERATE
THE
VEHICLE
WITHIN 24 HOURS OF WINDSHIELD INSTALLATION.
IT TAKES AT LEAST 24 HOURS FOR URETHANE
ADHESIVE TO CURE. IF IT IS NOT CURED, THE
WINDSHIELD MAY NOT PERFORM PROPERLY IN
AN ACCIDENT.
URETHANE ADHESIVES ARE APPLIED AS A SYS-
TEM. USE GLASS CLEANER, GLASS PREP SOL-
VENT, GLASS PRIMER, PVC (VINYL) PRIMER AND
PINCH WELD (FENCE) PRIMER PROVIDED BY THE
ADHESIVE MANUFACTURER. IF NOT, STRUCTURAL
INTEGRITY COULD BE COMPROMISED.
DAIMLERCHRYSLER
DOES
NOT
RECOMMEND
GLASS
ADHESIVE
BY
BRAND.
TECHNICIANS
SHOULD REVIEW PRODUCT LABELS AND TECHNI-
CAL DATA SHEETS, AND USE ONLY ADHESIVES
THAT THEIR MANUFACTURES WARRANT WILL
RESTORE A VEHICLE TO THE REQUIREMENTS OF
FMVSS 212. TECHNICIANS SHOULD ALSO INSURE
THAT PRIMERS AND CLEANERS ARE COMPATIBLE
WITH THE PARTICULAR ADHESIVE USED.
BE SURE TO REFER TO THE URETHANE MANU-
FACTURER’S
DIRECTIONS
FOR
CURING
TIME
SPECIFICATIONS, AND DO NOT USE ADHESIVE
AFTER ITS EXPIRATION DATE.
VAPORS THAT ARE EMITTED FROM THE URE-
THANE ADHESIVE OR PRIMER COULD CAUSE
PERSONAL INJURY. USE THEM IN A WELL-VENTI-
LATED AREA.
SKIN
CONTACT
WITH
URETHANE
ADHESIVE
SHOULD BE AVOIDED. PERSONAL INJURY MAY
RESULT.
ALWAYS WEAR EYE AND HAND PROTECTION
WHEN WORKING WITH GLASS.
CAUTION: Protect all painted and trimmed surfaces
from coming in contact with urethane or primers.
Be careful not to damage painted surfaces when
removing moldings or cutting urethane around
windshield.
REMOVAL
REMOVAL - JR-27 ONLY
EXTERIOR METHOD
(1) Open convertible top.
(2) Remove
header/A-pilllar
weatherstrip
from
weatherstrip retainers.
(3) Remove A-pillar
weatherstrip
retainer
and
molding.
(4) Remove header weatherstrip/molding.
(5) Mark top edge of the windshield glass at three
locations on the header.
(6) Remove windshield wiper arms.
(7) Remove cowl cover.
23 - 124
STATIONARY GLASS
JR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст