Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 679
(8) Disengage plastic J-strap retainer at bottom of
seat back (Fig. 14).
(9) Remove hog rings holding seat cover seam
cords to wires in seat back foam (Fig. 15) and (Fig.
16).
(10) Feed seat belt bezel and seat belt through
seat cover while pulling cover from seat back foam.
(11) Remove hog rings attaching the seat cover
seam cords and wires to seat back foam.
(12) Poll seat cover upward to mid point position.
(13) Remove head restraint guides (Fig. 17).
(14) Remove seat back cover from seat back foam
and frame.
INSTALLATION
INSTALLATION
NOTE: Do not reuse the recliner assembly attaching
bolts.
(1) Position cover on the top of seat back.
(2) Install new head restraint sleeve guides.
(3) Carefully roll cover down to the area that hog
rings are to be installed.
(4) Install hog rings.
(5) Install hog rings attaching back frame to foam
pad.
(6) Roll cover downward.
Fig. 14 Seat Cover Retainer Strip
1 - SEAT BACK
2 - PLASTIC RETAINER STRIP
Fig. 15 Hog Rings
1 - SEAT COVER SEAM STRAP
2 - HOG RING
Fig. 16 Mid Seat Back Hog Rings
1 - CUSHION COVER
2 - HOG RINGS
3 - CUSHION
Fig. 17 2 Head Restraint Guides
1 - SEAT CUSHION
2 - HOG RINGS
3 - HEADREST GUIDES
4 - BOTTOM OF TOP SEAT FRAME RAIL
JR
SEATS
23 - 113
FRONT SEAT BACK COVER (Continued)
(7) Engage the J-strap retainer
(8) Install lumbar support handle, if equipped.
(9) Install new head restraint sleeve guides.
(10) Install seat back to seat cushion. Tighten
recliner bolts to 40 N·m (30 ft. lbs.) torque. Tighten
pivot bolts to 12 N·m (9 ft. lbs.) torque.
(11) Install seat in vehicle.
(12) Install head restraint.
(13) Check seat back and headrest operation.
INSTALLATION - JR-27 ONLY
(1) Position seat back cover on to seat back foam
and frame.
(2) Install hog rings attaching seat back foam to
seat back frame.
(3) Feed seat belt bezel and seat belt through hole
in seat cover.
(4) Route recliner cable in front of metal strap at
bottom of the seat back frame (Fig. 11).
(5) Pull seat cover downward to first horizontal
trench in seat back foam.
(6) Align seat cover upper horizontal seam center
notch to center hog ring location.
(7) Install hog rings, center first, to attach upper
insert cover seam wire to wire in seat back foam.
(8) Install hog rings to attach seat cover seam
cords to wires in seat back foam.
(9) Pull seat cover down fully over seat back foam.
(10) Connect seat cover J-straps at bottom of seat
back.
(11) Install head restraint guides
(12) Slide long snaps on outboard portion of seat
belt bezel inside seat back cover and seat belt retrac-
tor cover.
(13) Install upper recliner handle and lumbar
adjustment handle, if so equipped.
(14) Attach lower seat belt anchor to bolt on seat
adjuster.
(15) Verify that seat belt is routed such that it will
not be twisted when engaged to the seat belt buckle.
(16) Install new nut attaching lower seat belt
anchor to seat frame (Fig. 8).
NOTE: Tighten the lower seat belt anchor nut to 47
N·m (35 ft. lbs.) torque.
(17) Verify that a minimum of three threads
extend beyond the lower seat belt anchor nut and
that the lower seat belt anchor swivels freely. If both
conditions are not found, check that the bolt is fully
engaged to the seat adjuster.
(18) Install seat to vehicle (Refer to 23 - BODY/
SEATS/SEAT - INSTALLATION).
(19) Check seat belt operation.
FRONT SEAT CUSHION SIDE
SHIELDS
REMOVAL
REMOVAL
(1) Remove seat from vehicle.
(2) Remove screws attaching seat cushion side
shield to the bottom and side of seat cushion (Fig. 18)
and (Fig. 19).
(3) Remove shield from seat
(4) Disconnect switch wire connectors, if equipped.
(5) Remove seat switches, if equipped.
Fig. 18 Bottom View of Side Shield
1 - RECLINER HANDLE AND FASTENER
2 - SIDE SHIELD FASTENERS
Fig. 19 Side View of Side Shield
1 - SIDESHIELD FASTENERS
23 - 114
SEATS
JR
FRONT SEAT BACK COVER (Continued)
REMOVAL - JR-27 ONLY
(1) Remove lower recliner handle.
(2) Remove screws attaching seat side shield to
seat frame.
(3) Remove screws attaching power seat switch to
side shield, if so equipped.
(4) Remove side shield from vehicle (Fig. 20).
INSTALLATION
INSTALLATION
(1) Transfer seat switches, if equipped.
(2) Connect switch wire connectors to cushion side
shield, if equipped.
(3) Place shield in position on seat cushion.
(4) Install screws attaching seat cushion side
shield.
(5) Install seat. Tighten front screws to 61 N·m (45
ft. lbs.) and the rear screws to 61 N·m (45 ft. lbs.).
INSTALLATION - JR-27 ONLY
(1) Position side shield near seat.
(2) Install screws attaching power seat switch to
side shield, if so equipped.
(3) Install screws attaching side shield to seat
frame.
(4) Install lower recliner handle.
FRONT SEAT CUSHION
REMOVAL - FRONT
(1) Remove seat from vehicle.
(2) Remove front seat cushion side shields and dis-
connect wire connectors, if equipped.
(3) Remove seat back.
(4) Remove seat cushion bolts.
(5) Disconnect wire harness fasteners from cushion
frame (Fig. 21).
(6) Remove seat cushion (Fig. 22).
INSTALLATION - FRONT
(1) Install
wire
harness
fasteners
to
cushion
frame.
(2) Install seat cushion bolts.
(3) Install seat back. Tighten recliner bolts to 12
N·m (9 ft. lbs.) torque. Tighten pivot bolts to 40 N·m
(30 ft. lbs.) torque.
(4) Connect switch wire connectors to the cushion
side shield, if equipped.
(5) Install cushion side shields.
(6) Install seat in vehicle.
Fig. 20 Front Seat Side Shield
1 - SEAT FRAME
2 - SEAT SIDE SHIELD
3 - POWER SEAT SWITCH
Fig. 21 Front Seat Cushion Wire Harness
1 - WIRE HARNESS
Fig. 22 Front Seat Cushion
1 - FRONT SEAT CUSHION
JR
SEATS
23 - 115
FRONT SEAT CUSHION SIDE SHIELDS (Continued)
FRONT SEAT CUSHION COVER
REMOVAL - FRONT SEAT CUSHION COVER
NOTE: Fabric covered cushions are serviced as an
assembly.
(1) Remove seat from vehicle.
(2) Remove front seat cushion side shields and dis-
connect wire connectors, if equipped.
(3) Remove seat back.
(4) Remove seat cushion bolts.
(5) Disconnect wire harness fasteners from cushion
pan. (Fig. 21).
(6) Disengage J-strap attaching seat cover from
the seat cushion frame (Fig. 23).
(7) Pull cover off to the hog rings (Fig. 24).
(8) Cut hog rings attaching seat cover seat cush-
ion.
(9) Remove seat cushion cover from seat cushion.
INSTALLATION - FRONT SEAT CUSHION
COVER
NOTE: Fabric covered cushions are serviced as an
assembly.
(1) Position seat cover on cushion.
(2) Align seat cover with cushion alignment inden-
tations (Fig. 25).
(3) Install hog rings.
(4) Engage J-strap attaching seat cover to front of
seat cushion frame.
(5) Install wire harness fasteners to cushion pan.
(6) Install seat cushion bolts.
(7) Install seat back. Tighten recliner bolts to 12
N·m (9 ft. lbs.) torque. Tighten pivot bolts to 40 N·m
(30 ft. lbs.) torque.
(8) Connect switch wire connectors to the cushion
side shield, if equipped.
(9) Install cushion side shields.
(10) Install seat in vehicle.
Fig. 23 Front Seat Cushion J-Strap
1 - J-STRAP
Fig. 24 Seat Cushion Cover
1 - SEAT COVER
2 - HOG RINGS
Fig. 25 Seat Cushion
1 - SEAT CUSHION
2 - ALIGNMENT INDENTATIONS
3 - HOOK AND LOOP FASTENER
23 - 116
SEATS
JR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст