Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 680
REAR SEAT
DESCRIPTION
Refer to (Fig. 26) for more information while ser-
vicing the rear seat.
Fig. 26 Rear Seat Exploded View
1 - SEAT BACK FOAM AND FRAME
2 - SEAT BACK COVER
3 - SEAT CUSHION COVER
4 - SEAT CUSHION FOAM AND FRAME
JR
SEATS
23 - 117
REAR SEAT CUSHION
REMOVAL
REMOVAL - REAR
NOTE: Fabric covered cushions are serviced as an
assembly.
(1) Pull upward at forward edge of cushion each
retainer loop of the rear seat cushion to disengage
retainer loops from cups in floor (Fig. 27).
(2) Guild seat belts through loops.
(3) Remove rear seat cushion from vehicle.
REMOVAL - JR-27 ONLY
NOTE: Special care should be taken when removing
rear seat cushion to prevent damage to the cushion
frame. Remove cushion at attachment areas, not at
wing area.
(1) Push firmly rearward and upward at one
attachment point and disengage wire loops from
retainers in floor pan (Fig. 28).
(2) Repeat for other attachment point.
(3) Separate rear seat cushion from vehicle.
INSTALLATION
INSTALLATION - REAR
NOTE: Fabric covered cushions are serviced as an
assembly.
NOTE: Verify visibility of “Latch” bars in the seat
bite area.
(1) Place rear seat cushion in position.
(2) Guild seat belts through loops.
(3) Engage retainer loops into cup on floor kick-up.
(4) Push downward at forward edge at each
retainer loop of the rear seat cushion to engage
retainers.
INSTALLATION - JR-27 ONLY
NOTE: Special care should be taken when removing
rear seat cushion to prevent damage to the cushion
frame. Remove cushion at attachment areas, not at
wing area.
(1) Position rear seat cushion in vehicle.
(2) Place inner seat belts on top of seat cushion.
(3) Push seat cushion rearward and align wire
loops to retainers in floor pan.
(4) Push rear seat cushion firmly downward and
engage wire loops to retainers in floor pan.
Fig. 27 Rear Seat Cushion
1 - RETAINER LOOP
2 - REAR SEAT BACK
3 - REAR SEAT CUSHION
4 - CUPS
Fig. 28 Rear Seat Cushion
1 - REAR SEAT BACK
2 - REAR SEAT CUSHION
3 - INNER SEAT BELTS
23 - 118
SEATS
JR
REAR SEAT CUSHION COVER
REMOVAL
REMOVAL - REAR SEAT CUSHION COVER
(1) Remove rear seat cushion.
(2) Disengage the J-strap retainers (Fig. 29).
(3) Cut hog rings to free cover (Fig. 30).
(4) Remove seat cushion cover from seat cushion.
REMOVAL - JR-27 ONLY
(1) Remove rear seat cushion from vehicle (Refer
to 23 - BODY/SEATS/SEAT CUSHION - REMOVAL).
(2) Place seat cushion on a suitable work surface
in inverted position.
(3) Remove hog rings around perimeter of seat
cushion attaching seat cushion cover to seat cushion
frame.
(4) Pull seat cover from seat cushion frame and
seat cushion foam.
(5) Remove hog rings attaching seat cover seam
wires to seat foam wires.
(6) Remove seat cover from seat frame and seat
cushion foam.
INSTALLATION
INSTALLATION - REAR SEAT CUSHION COVER
(1) Position seat cushion cover on cushion.
(2) Install hog rings to seat cover.
(3) Engage the J-strap retainers.
(4) Steam wrinkles from seat cushion, if necessary.
(5) Install seat cushion.
INSTALLATION - JR-27 ONLY
(1) Position seat cushion cover to seat cushion
frame and seat cushion foam.
(2) Install a hog ring at each hog ring location to
attach seat cushion cover seam wires to wires in seat
cushion foam. Begin at center location and work out-
ward.
(3) Repeat above steps for opposite inboard vertical
seam, both outboard vertical seams, and for the hor-
izontal seams.
(4) Pull seat cover over seat cushion frame and
seat cushion foam.
(5) Install hog rings at hog ring locators around
perimeter of seat cushion foam attaching seat cush-
ion cover to seat cushion frame.
(6) Install rear seat cushion to vehicle (Refer to 23
- BODY/SEATS/SEAT CUSHION - INSTALLATION).
REAR SEAT BACK
REMOVAL
REMOVAL - FOLDING BACK
NOTE: Fabric covered cushions are serviced as an
assembly.
(1) Remove rear seat cushion. (Refer to 23 - BODY/
SEATS/SEAT CUSHION - REMOVAL)
(2) Remove the rear seat buckles and belt anchors.
(Refer
to
8
-
ELECTRICAL/RESTRAINTS/SEAT
BELT - REAR INBOARD - REMOVAL)
(3) Remove the outer seat back bracket nuts (Fig.
31).
(4) Release folding rear seat back latches.
(5) Remove seat back from vehicle.
REMOVAL - JR-27 ONLY
(1) Remove rear seat cushion (Refer to 23 - BODY/
SEATS/SEAT CUSHION - REMOVAL).
Fig. 29 Rear Seat Cushion Cover J-Straps
1 - J-STRAPS
Fig. 30 Rear Seat Cushion Cover Hog Rings
1 - HOG RINGS
JR
SEATS
23 - 119
(2) Pull bottom of rear seat back forward until seat
back brackets clear studs on floor pan (Fig. 32).
(3) Push upward on rear seat back and disengage
hooks attaching seat back to rear seat back support.
(4) Remove rear seat back from vehicle.
INSTALLATION
INSTALLATION - FOLDING BACK
NOTE: Fabric covered cushions are serviced as an
assembly.
(1) Place the four seat back brackets over the body
mounted weld studs and position seat back in vehi-
cle.
(2) Engage folding rear seat back latch.
(3) Install the outer seat back bracket nuts and
tighten to 61 Nm (45 ft. lbs.).
(4) Install the rear seat buckles and belt anchors.
(Refer
to
8
-
ELECTRICAL/RESTRAINTS/SEAT
BELT - REAR INBOARD - INSTALLATION)
(5) Install rear seat cushion. (Refer to 23 - BODY/
SEATS/SEAT CUSHION - INSTALLATION)
INSTALLATION - JR-27 ONLY
(1) Position rear seat back in vehicle.
(2) Tilt rear seat back rearward and raise seat
back above retaining brackets on rear seat back sup-
port.
(3) Lower rear seat back until center loop begins
to engage.
(4) Lower rear seat back and push rearward on
outboard corners of seat back to engage outboard
hooks to brackets on rear seat back support.
(5) Push downward on rear seat back until all
hooks are fully engaged into retaining brackets.
(6) Install rear seat cushion.
REAR SEAT BACK COVER
REMOVAL - JR-27 ONLY
(1) Remove rear seat back from vehicle (Refer to
23 - BODY/SEATS/REAR SEAT BACK - REMOVAL).
(2) Place seat back on a suitable work surface in
inverted position.
(3) Remove hog rings around perimeter of seat
back holding seat back cover to seat back frame.
(4) Pull seat cover from seat back frame and seat
back foam.
(5) Remove any hog rings holding seat cover seam
wires to seat foam wires.
(6) Remove seat cover from seat frame and seat
back foam.
INSTALLATION - JR-27 ONLY
(1) Position seat cover to seat back frame and seat
back foam.
(2) Align notch in center of seat back cover vertical
seam to center hog ring locator.
(3) Install a hog ring at each hog ring location,
center first, attaching seat back cover seam to wires
in seat back foam.
(4) Repeat the above steps for the opposite inboard
vertical seam, both outboard vertical seams, and the
lower horizontal seam.
(5) Install hog rings at each hog ring locator, cen-
ter first, to attach ends of vertical portions of
U-shaped wires to vertical foam wires.
(6) Align notch in center of upper horizontal seat
cover seam to center hog ring location.
Fig. 31 REAR SEAT BACK
1 - SEAT BACK
2 - NUTS
3 - BRACKETS
Fig. 32 Rear Seat Back
1 - REAR SEAT BACK SUPPORT
2 - FLOOR PAN
3 - REAR SEAT BACK
4 - RETAINING BRACKET
23 - 120
SEATS
JR
REAR SEAT BACK (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст