Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 678
INSTALLATION
INSTALLATION
CAUTION: Do not handle by seat adjuster release bar.
NOTE: Ensure that the seat tracks are rearward.
Ensure the seat tracks on the right and left are in
equal latch positions.
(1) Place front seat in position in vehicle.
(2) Connect front seat wire harness connector to
body harness connector.
(3) Install bolts to attach front of seat track to the
floor kick up. Tighten bolts to 61 N·m (45 ft. lbs.) torque.
(4) Slide seat forward and install bolts attaching
rear of seat track to the floor. Tighten bolts to 61
N·m (45 ft. lbs.) torque.
(5) Verify front seat operation.
INSTALLATION - MANUAL - JR-27
CAUTION: It is important that the following steps be
done correctly to insure that the seat tracks are prop-
erly timed prior to securing the seats to the vehicle.
(1) Adjust seat back to vertical position using
either recliner handle.
WARNING: DO NOT GRAB EITHER RECLINER HANDLE
OR TOWEL BAR WHEN HANDLING SEAT. THE SEAT
TRACKS ARE SPRING LOADED AND WILL RELEASE.
(2) Turn seat upside down so that the seat tracks
can be seen.
(3) Securely grasp the spring loaded outboard
track rail and while lifting the towel bar, position the
lower rail so that it is locked in the forth hole from
the end (Fig. 5).
(4) Position the inboard seat track rail so that it is
identical to the outboard track lower rail.
(5) Return seat to upright position.
(6) Position seat in vehicle.
(7) Tilt seat rearward and connect wire connector
to seat belt pretensioner.
(8) Push downward on seat cushion to ensure that
the front mounting brackets are fully seated to floor
pan crossmember.
(9) Install and tighten rear outboard bolt seat to
side sill pylon.
(10) Install and tighten forward outboard bolt
attaching seat to crossmember.
(11) Install
and
tighten
forward
inboard
bolt
attaching seat to crossmember.
(12) Move seat to full forward position. Push rear-
ward slightly on seat to ensure that the adjuster
latches are engaged on both seat tracks.
(13) Install and tighten rear inboard bolt attaching
seat to floor pan.
(14) Install and tighten middle outboard bolt
attaching seat to side sill pylon.
(15) Move seat forward and rearward and check
the efforts to move seat. If effort is to high loosen
seat track bolts and retighten to the proper torque.
NOTE: Tighten all seat track retaining bolts to 61
N·m (45 ft. lbs.) torque.
INSTALLATION - POWER - JR-27 ONLY
(1) Adjust seat back to vertical position using
either recliner handle.
(2) Position seat in vehicle.
(3) Tilt seat rearward and connect wire connector
to seat belt pretensioner and power seat mechanism.
(4) Push downward on seat cushion to ensure that
the front mounting brackets are fully seated to floor
pan crossmember.
(5) Use power seat switch to move seat to full rear-
ward position.
(6) Install and tighten rear outboard bolt attaching
seat to side sill pylon.
(7) Install
and
tighten
forward
outboard
bolt
attaching seat to crossmember.
(8) Install and tighten forward inboard bolt attach-
ing seat to crossmember.
(9) Use power seat switch to move seat to full for-
ward position.
(10) Install and tighten rear inboard bolt attaching
seat to floor pan.
(11) Install
and
tighten
middle
outboard
bolt
attaching seat to side sill pylon.
NOTE: Tighten all seat track retaining bolts to 61
N·m (45 ft. lbs.) torque.
Fig. 5 Seat Track Position
1 - REAR OF SEAT TRACK
2 - FORTH HOLE POSITION
JR
SEATS
23 - 109
FRONT SEAT (Continued)
FRONT SEAT BACK
REMOVAL
REMOVAL
(1) Remove seat from vehicle.
(2) Remove seat cushion side shields.
NOTE: Do not reuse the recliner assembly attaching
bolts.
(3) Remove bolts attaching recliner to seat back
cushion frame (Fig. 6).
(4) Remove pivot bolts (Fig. 7).
(5) Disconnect any electrical connectors to the seat
back, if equipped.
(6) Remove seat back from seat cushion.
REMOVAL - JR-27 ONLY
(1) Remove seat from vehicle (Refer to 23 - BODY/
SEATS/SEAT - REMOVAL).
(2) Remove recliner handle.
(3) Remove seat side shield (Refer to 23 - BODY/
SEATS/SEAT
CUSHION
SIDE
SHIELDS
-
REMOVAL).
(4) Remove recliner cable eyelet clip (Fig. 8).
(5) Remove
recliner
cable
from
arm
on
seat
adjuster and feed cable back through hole in seat
adjuster.
NOTE: The torque prevailing nuts used to secure
the lower seat belt anchor and seat belt buckle are
not reusable. Verify availability prior to proceeding.
(6) Remove seat cushion (Refer to 23 - BODY/
SEATS/SEAT CUSHION - REMOVAL).
(7) Remove nut attaching lower seat belt anchor to
seat frame (Fig. 8).
(8) Back off nut attaching seat belt buckle to seat
frame.
(9) Remove seat belt buckle pretensioner from seat
frame.
(10) Remove E-clip and washer from easy entry
rod at inboard side of seat, manual seat only.
(11) Remove rod from seat back, manual seat only.
(12) Remove pivot bolts attaching seat back to seat
frame.
WARNING: DO NOT PULL ON UPPER RECLINER
HANDLE OR RECLINER CABLE END AT ANY POINT
UNTIL THE LEAD SCREW IS REMOVED IT IS
UNDER A HIGH PRESSURE LOAD.
Fig. 6 Recliner Attaching Bolt
1 - RECLINER BOLT
Fig. 7 Remove Seat Back
1 - RECLINER BOLT HOLE
2 - SEAT BACK BOLT HOLE
3 - J-STRAP RETAINER
Fig. 8 Lower Seat Belt Anchor And Recliner Cable
1 - RECLINER CABLE
2 - LOWER SEAT BELT ANCHOR
23 - 110
SEATS
JR
(13) Remove bolt attaching recliner lead screw to
seat frame.
(14) Remove seat back from seat frame (Refer to
23 - BODY/SEATS/SEAT BACK - REMOVAL).
(15) Unscrew lead screw from recliner mechanism
(Fig. 9).
(16) Remove lead screw, spring and spring plate
(Fig. 10).
INSTALLATION
INSTALLATION
(1) Position seat back on cushion.
(2) Install both pivot bolts and tighten 40 N·m (30
ft. lbs.).
NOTE: Do not reuse the recliner assembly attaching
bolts.
(3) Install bolts attaching recliner to seat back
frame and tighten to 12 N·m (9 ft. lbs.).
(4) Install seat cushion side shields.
(5) Install seat in vehicle.
INSTALLATION - JR-27 ONLY
(1) Screw recliner lead screw into recliner mecha-
nism. (Fig. 9).
WARNING: DO NOT PULL ON UPPER RECLINER
HANDLE OR RECLINER CABLE END AT ANY POINT
UNTIL THE LEAD SCREW IS REMOVED.
(2) Route recliner cable in front of metal strap at
bottom of the seat back frame (Fig. 11).
(3) Position seat back to seat frame (Refer to 23 -
BODY/SEATS/SEAT BACK - INSTALLATION).
(4) Install bolt attaching recliner lead screw to
seat frame. Tighten bolt to 45 N·m (33 ft. lbs.)
torque.
(5) Install pivot bolts attaching seat back to seat
frame. Tighten bolts to 51 N·m (38 ft. lbs.) torque.
(6) Attach easy entry rod to seat back, passenger
side only.
(7) Install easy entry washer and E-clip, passenger
side only.
(8) Install seat cushion (Refer to 23 - BODY/
SEATS/SEAT CUSHION - INSTALLATION).
(9) Feed
recliner
cable
through
hole
in
seat
adjuster and engage cable eyelet to arm on seat
adjuster.
(10) Install new recliner cable eyelet clip to arm on
seat frame (Fig. 8).
Fig. 9 Recliner Lead Screw
1 - RECLINER MECHANISM
2 - LEAD SCREW
3 - SEAT FRAME
Fig. 10 Recliner Lead Screw
1 - LEAD SCREW SPRING PLATE
2 - LEAD SCREW
Fig. 11 Route Recliner Cable
1 - NEW CABLE ROUTING (DRIVER SEAT)
2 - BACK FRAME STRAP
JR
SEATS
23 - 111
FRONT SEAT BACK (Continued)
(11) Position seat belt buckle pretensioner to bolt
on side of seat adjuster and install nut.
NOTE: Apply thread adhesive to threads before
installing nut.
(12) Position lower seat belt anchor to bolt on seat
adjuster.
(13) Verify that seat belt is routed such that it will
not be twisted when engaged to the seat belt buckle.
(14) Install new nut attaching lower seat belt
anchor to seat frame (Fig. 8).
NOTE: Tighten the lower seat belt anchor and seat
belt buckle nuts to 47 N·m (35 ft. lbs.) torque.
NOTE: Verify that a minimum of three threads
extend beyond the lower seat belt anchor nut and
that the lower seat belt anchor swivels freely. If
both conditions are not found, remove nut, torque
bolt, and while preventing bolt from turning, torque
nut.
(15) Install seat side shield (Refer to 23 - BODY/
SEATS/SEAT CUSHION SIDE SHIELDS - INSTAL-
LATION). Verify that side and rear screws go
through the rubber bellows.
(16) Install seat to vehicle (Refer to 23 - BODY/
SEATS/SEAT - INSTALLATION).
FRONT SEAT BACK COVER
REMOVAL
REMOVAL
(1) Remove seat from vehicle.
(2) Remove head restraint.
(3) Remove front seat back.
(4) Remove lumbar support handle, if equipped.
(5) Disengage the J-strap retainer (Fig. 7).
(6) Remove hog rings attaching foam pad to back
frame (Fig. 12).
(7) Roll seat back cover up to the next hog rings
and remove hog rings.
(8) For bonded seat back cover separate frame
from bonded cover and pad.
(9) Roll cover to top of cushion and remove head
restraint sleeve guides. Do not reuse head restraint
sleeve guides.
(10) Remove cover from seat back.
REMOVAL - JR-27 ONLY
(1) Remove seat from vehicle (Refer to 23 - BODY/
SEATS/SEAT - REMOVAL).
(2) Remove head restraint (Fig. 13) by depressing
headrest button and using a pick tool in access hole
simultaneously.
(3) Remove seat back (Refer to 23 - BODY/SEATS/
SEAT BACK - REMOVAL).
(4) Remove upper recliner handle and lumber
adjustment handle, if so equipped.
(5) Remove seat side shield (Refer to 23 - BODY/
SEATS/SEAT
CUSHION
SIDE
SHIELDS
-
REMOVAL).
(6) Remove nut attaching lower seat belt anchor to
seat frame (Fig. 8) (Refer to 23 - BODY/SEATS/SEAT
BACK - REMOVAL).
(7) Remove seat belt bezel.
NOTE: The torque prevailing nut used to secure the
lower seat belt anchor is not reusable. Verify avail-
ability prior to proceeding.
Fig. 13 Head Restraint Removal
1 - HEADREST
2 - SEAT
3 - ACCESS HOLE
4 - PICK TOOL
Fig. 12 Front Seat Back Hog Rings
1 - SEAT COVER
2 - HOG RINGS
3 - CUSHION
23 - 112
SEATS
JR
FRONT SEAT BACK (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст