Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 114
Symptom:
*VTSS DOES NOT TRIP FROM LEFT REAR DOOR
POSSIBLE CAUSES
INVALID DOOR AJAR INPUT
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, read the LR DR AJAR SW status.
Open the left rear door.
Does the DRBIII
t display CLOSED?
All
Yes
→ Replace the Body Control Module.
Perform VTSS VERIFICATION TEST - 1A.
No
→ Refer to symptom LEFT REAR DOOR AJAR CKT OPEN in the
DOOR AJAR category.
441
VEHICLE THEFT/SECURITY
Symptom:
*VTSS DOES NOT TRIP FROM PASSENGER DOOR
POSSIBLE CAUSES
INVALID DOOR AJAR INPUT
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, read the PAS DR AJAR SW status.
Open the passenger door.
Does the DRBIII
t display CLOSED?
All
Yes
→ Replace the Body Control Module.
Perform VTSS VERIFICATION TEST - 1A.
No
→ Refer to symptom PASSENGER DOOR AJAR CKT OPEN in the
DOOR AJAR category.
442
VEHICLE THEFT/SECURITY
Symptom:
*VTSS DOES NOT TRIP FROM RIGHT REAR DOOR
POSSIBLE CAUSES
INVALID DOOR AJAR INPUT
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, read the RR DR AJAR SW status.
Open the right rear door.
Does the DRBIII
t display CLOSED?
All
Yes
→ Replace the Body Control Module.
Perform VTSS VERIFICATION TEST - 1A.
No
→ Refer to symptom RIGHT REAR DOOR AJAR CKT OPEN in the
DOOR AJAR category.
443
VEHICLE THEFT/SECURITY
Symptom:
*VTSS INDICATOR INOPERATIVE
POSSIBLE CAUSES
VTSS INDICATOR LAMP TEST
OPEN FUSED B(+) CIRCUIT
OPEN JUNCTION BLOCK
INSTRUMENT CLUSTER
OPEN VTSS LED
VTSS INDICATOR DRIVER CIRCUIT OPEN
BODY CONTROL MODULE INTERNAL MALFUNCTION
OPEN FUSE #7
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, actuate the VTSS LAMP.
Does the VTSS Lamp flash while actuating the Lamp?
All
Yes
→ Replace the Body Control Module.
Perform VTSS VERIFICATION TEST - 1A.
No
→ Go To 2
2
Remove and inspect Fuse #7 in the Junction Block.
Is the fuse open?
All
Yes
→ Inspect/repair the Fused B(+) circuit for a short to ground.
Replace the Fuse.
Perform VTSS VERIFICATION TEST - 1A.
No
→ Go To 3
3
Reinstall Fuse #7 in the Junction Block.
Gain access to the Junction Block connector C7.
While back probing, measure the voltage of the Fused B(+) circuit at the Junction
Block connector C7.
Is the voltage above 10.0 volts?
All
Yes
→ Go To 4
No
→ Replace the Junction Block.
Perform VTSS VERIFICATION TEST - 1A.
4
Disconnect the Instrument Cluster harness connector.
Measure the voltage of the Fused B(+ ) circuit at cavity 21.
Is the voltage above 10.0 volts?
All
Yes
→ Go To 5
No
→ Repair the Fused B(+) circuit for an open.
Perform VTSS VERIFICATION TEST - 1A.
444
VEHICLE THEFT/SECURITY
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст