Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 115
TEST
ACTION
APPLICABILITY
5
Remove the VTSS Indicator Bulb from the Instrument Cluster.
Inspect the VTSS Indicator Bulb and socket.
Is there a problem with the bulb or socket?
All
Yes
→ Repair or replace the VTSS Indicator Bulb or socket as needed.
Perform VTSS VERIFICATION TEST - 1A.
No
→ Go To 6
6
Disconnect the Instrument Cluster harness connector.
Connect a voltmeter positive probe to a 12.0 volt supply and connect the ground probe
to the VTSS Indicator Driver circuit at the Instrument Cluster connector.
Turn the ignition on.
With the DRB in Vehicle Theft, actuate the VTSS Indicator lamp.
Is the voltage above 10.0 volts when the VTSS Indicator lamp is actuated?
All
Yes
→ Replace the Instrument Cluster assembly.
Perform VTSS VERIFICATION TEST - 1A.
No
→ Go To 7
7
Disconnect the Instrument Cluster harness connector.
Disconnect the BCM C1 harness connector.
Measure the resistance of the VTSS Indicator Driver circuit between the Instrument
Cluster connector and the BCM C1 connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Replace the Body Control Module.
Perform VTSS VERIFICATION TEST - 1A.
No
→ Repair the VTSS Indicator Driver circuit for an open.
Perform VTSS VERIFICATION TEST - 1A.
445
VEHICLE THEFT/SECURITY
*VTSS INDICATOR INOPERATIVE —
Continued
Symptom:
*VTSS NO TRIP FROM DECKLID
POSSIBLE CAUSES
INVALID DECKLID AJAR INPUT
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, read the DECKLID AJAR SW status.
Open the decklid.
Does the DRBIII
t display CLOSED?
All
Yes
→ Replace the Body Control Module.
Perform VTSS VERIFICATION TEST - 1A.
No
→ Refer to symptom DECKLID DOOR AJAR CKT OPEN in the
DOOR AJAR category.
446
VEHICLE THEFT/SECURITY
Symptom:
*VTSS WILL NOT ARM
POSSIBLE CAUSES
CHECK THE VTSS STATUS
CHECK THE BCM FOR DTCS
BODY CONTROL MODULE INTERNAL MALFUNCTION
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, check that the Theft Alarm is enabled.
Was the Theft Alarm enabled?
All
Yes
→ Go To 2
No
→ With the DRBIIIt, enable the Vehicle Theft Security System
(VTSS).
Perform VTSS VERIFICATION TEST - 1A.
2
With the DRBIII
t, read the active DTC’s.
Are any VTSS related DTC’s present?
All
Yes
→ Refer to the Symptom List and diagnose the appropriate symp-
tom.
No
→ Replace the Body Control Module.
Perform VTSS VERIFICATION TEST - 1A.
447
VEHICLE THEFT/SECURITY
Symptom:
WIPER ON/OFF RELAY OUTPUT SHORTED HIGH
When Monitored and Set Condition:
WIPER ON/OFF RELAY OUTPUT SHORTED HIGH
When Monitored:
Continuoulsy.
Set Condition:
BCM detects a high level on the wiper on/off relay output when it is
attempting to turn on the wipers.
POSSIBLE CAUSES
INTERMITTENT CONDITION
SHORT TO BATTERY
HI/LO WIPER RELAY
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, clear all BCM DTC’s.
Actuate the Wipers.
With the DRBIII
t, read the DTC information.
Does the DRBIII
t read: Wiper On/Off Relay Output Shorted High?
All
Yes
→ Go To 2
No
→ The condition that caused the symptom is currently not present.
Inspect the related wiring for a possible intermittent condition.
Look for any chafed, pierced, pinched, or partially broken wires.
Perform BODY VERIFICATION TEST - VER 1.
2
Turn the ignition off.
Disconnect the HI/LO Wiper Relay.
Disconnect the BCM from the junction block.
Measure the voltage of the HI/LO Wiper Relay Control Circuit.
Is the voltage below 5.0 volts?
All
Yes
→ Repair the Wiper HI/LO Relay Control Circuit for a short to
battery
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
3
Turn the ignition off.
Install a known good relay in place of the HI/LO Wiper Relay.
Turn the Wipers on.
Do the Wipers operate normally?
All
Yes
→ Replace the HI/LO Wiper Relay.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
448
WINDSHIELD WIPER & WASHER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст