Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 669
(13) Disconnect the console wiring connectors and
unclip the push in fasteners.
(14) Using a trim stick or equivalent, gently pry
up on and remove the right sill plate.
(15) Remove the two screws to the right cowl kick
panel and remove from vehicle (Refer to 23 - BODY/
INTERIOR/COWL TRIM - REMOVAL).
(16) Using a trim stick or equivalent, gently pry
out on the right end cover and remove from vehicle
(Refer to 23 - BODY/INSTRUMENT PANEL/IN-
STRUMENT PANEL END CAP - REMOVAL).
(17) Using a trim stick or equivalent, gently pry
out on the right A-pillar trim and remove from vehi-
cle (Refer to 23 - BODY/INTERIOR/A-PILLAR TRIM
- REMOVAL).
(18) Open the glove box. Pinch in on the sides and
drop to the floor. Pull down to disengage hinges.
(19) Disconnect the right door harness connectors
located within the A-pillar.
(20) Remove the four right A-pillar instrument
panel retainers.
(21) Remove the right silencer.
(22) Remove the one right side, center instrument
panel support bolt.
(23) Using a trim stick or equivalent, gently pry
up on and remove the left sill plate (Refer to 23 -
BODY/INTERIOR/DOOR SILL TRIM - REMOVAL).
(24) Remove the two screws to the left cowl kick
panel and remove from vehicle.
(25) Using a trim stick or equivalent, gently pry
out on the left end cover and remove from vehicle
(Refer to 23 - BODY/INSTRUMENT PANEL/IN-
STRUMENT PANEL END CAP - REMOVAL).
(26) Using a trim stick or equivalent, gently pry
out on the left A-pillar trim and remove from vehicle
(Refer to 23 - BODY/INTERIOR/A-PILLAR TRIM -
REMOVAL).
(27) Disconnect the left door harness connectors
located within the A-pillar.
(28) Remove the four left A-pillar instrument panel
retainers.
(29) Remove five screws and one wire connector to
left lower instrument panel trim bezel (Refer to 23 -
BODY/INSTRUMENT
PANEL/INSTRUMENT
PANEL TRIM - REMOVAL).
(30) Remove the left silencer.
(31) Remove the one left side, center instrument
panel support bolt.
(32) Remove one bolt to the left side support strut
to bulkhead.
(33) Disconnect the junction block wiring connec-
tors.
(34) Remove two screws to the steering column
shrouds and remove.
(35) Disconnect all the column wiring and unclip
the harness from the steering column.
(36) Disconnect the transmission shift interlock
and wire connector.
(37) Remove the four steering column retaining
bolts and drop column to floor.
(38) Using a trim stick or equivalent, pry up on
the rear of the top cover and pull rearward as you lift
off of instrument panel (Refer to 23 - BODY/IN-
STRUMENT PANEL/INSTRUMENT PANEL TOP
PAD - REMOVAL).
(39) Remove instrument panel pad.
(40) Remove seven bolts and five screws attaching
instrument panel to fence line and cowl side.
(41) With the help of an assistant, lift up instru-
ment panel and move rearward to remove. Tilt the
panel rearward to prevent the coolant from leaking
out.
If replacing the instrument panel, transfer all non
damaged parts and wiring harness to the new instru-
ment panel assembly.
TO SEPARATE THE INSTRUMENT PANEL AND
HVAC UNIT HOUSINGS
• Disconnect the HVAC wiring connector to the
instrument panel wire harness.
• Remove the two bolts and two nuts holding the
HVAC housing to the instrument panel.
• Lift the instrument panel off the HVAC housing
to separate.
INSTALLATION
The Instrument Panel and HVAC assemblies are
installed together as one assembly. They must be
reconnected before installation.
TO CONNECT THE INSTRUMENT PANEL AND HVAC
UNIT HOUSINGS
• Place the instrument panel on the HVAC hous-
ing.
• Install the two bolts and two nuts holding the
HVAC housing to the instrument panel.
• Connect the HVAC wiring connector to the
instrument panel wire harness.
If replacing the instrument panel, transfer all non
damaged parts and wiring harness to the new instru-
ment panel assembly.
(1) With the help of an assistant, place the instru-
ment panel in the vehicle, carefully guiding the
HVAC housing studs through the bulkhead and into
position.
(2) Install the seven bolts and five screws attach-
ing instrument panel to fence line and cowl side (Fig.
4).
(3) Place instrument panel pad into position.
(4) Install the instrument panel top cover (Refer to
23 - BODY/INSTRUMENT PANEL/INSTRUMENT
PANEL TOP PAD - INSTALLATION).
JR
INSTRUMENT PANEL
23 - 73
INSTRUMENT PANEL ASSEMBLY (Continued)
(5) Install the four steering column retaining bolts.
(6) Connect the transmission shift interlock and
wire connector.
(7) Connect all the column wiring and clip the har-
ness to the steering column.
(8) Install two screws to the steering column
shrouds.
(9) Connect the junction block wiring connectors.
(10) Install one bolt to the left side support strut
to bulkhead.
(11) Install five screws and one wire connector to
left lower instrument panel trim bezel (Refer to 23 -
BODY/INSTRUMENT
PANEL/INSTRUMENT
PANEL TRIM - INSTALLATION).
(12) Install the one left side, center instrument
panel support bolt.
(13) Install the left silencer.
(14) Install the four left A-pillar instrument panel
retainers.
(15) Connect the right door harness connectors
located within the A-pillar.
(16) Install the right A-pillar trim (Refer to 23 -
BODY/INTERIOR/A-PILLAR
TRIM
-
INSTALLA-
TION).
(17) Install the left end cover (Refer to 23 - BODY/
INSTRUMENT PANEL/INSTRUMENT PANEL END
CAP - INSTALLATION).
(18) Install the two screws to the left cowl trim
panel (Refer to 23 - BODY/INTERIOR/COWL TRIM -
INSTALLATION).
(19) Install the left door sill plate (Refer to 23 -
BODY/INTERIOR/DOOR SILL TRIM - INSTALLA-
TION).
(20) Install the one right side, center instrument
panel support bolt.
(21) Install the right silencer.
(22) Install the four right A-pillar instrument
panel retainers.
(23) Connect the right door harness connectors
located within the A-pillar.
(24) Install the glove box.
(25) Install the right A-pillar trim (Refer to 23 -
BODY/INTERIOR/A-PILLAR
TRIM
-
INSTALLA-
TION).
(26) Install the right end cover (Refer to 23 -
BODY/INSTRUMENT
PANEL/INSTRUMENT
PANEL END CAP - INSTALLATION).
(27) Install the two screws to the right cowl trim
panel (Refer to 23 - BODY/INTERIOR/COWL TRIM -
INSTALLATION).
(28) Install the right door sill plate (Refer to 23 -
BODY/INTERIOR/DOOR SILL TRIM - INSTALLA-
TION).
(29) Connect the console wiring connectors and
clip the push in fasteners in.
Fig. 4 INSTRUMENT PANEL REMOVAL
1 - INSTRUMENT PANEL TO PLENUM SCREW
2 - INSTRUMENT PANEL STEERING COLUMN TO COWL
PLENUM SCREW
3 - RIGHT COWL SIDE BOLTS
4 - INSTRUMENT PANEL CENTER BRACE TO FLOOR
5 - LEFT COWL SIDE BOLTS
23 - 74
INSTRUMENT PANEL
JR
INSTRUMENT PANEL ASSEMBLY (Continued)
(30) Install the left and right rear floor heat ducts
(Fig. 3).
(31) Connect the two harness connectors to the
amplifier.
(32) Install the amplifier (Refer to 8 - ELECTRI-
CAL/AUDIO/AMPLIFIER - INSTALLATION).
(33) Install floor center console. Install two mount-
ing screws in the front and two mounting screws
inside console storage bin (Refer to 23 - BODY/INTE-
RIOR/FLOOR CONSOLE - INSTALLATION).
(34) Install the transmission range indicator bezel
and one screw to shift knob.
(35) Connect the battery negative remote cable.
(36) Install the driver and passenger seats (Refer
to 23 - BODY/SEATS/SEAT - INSTALLATION).
(37) Hoist vehicle and install the lower HVAC
housing retaining nut.
(38) Lower vehicle from hoist.
(39) Install the two top HVAC housing retaining
nuts in engine compartment (Fig. 2).
(40) Install one bolt retaining the A/C lines to the
right strut tower.
(41) Top off the coolant (Refer to 7 - COOLING/
ENGINE/COOLANT - STANDARD PROCEDURE).
(42) Recharge the A/C refrigerant with specified
amount. Refer to placard in engine compartment
(Refer to 24 - HEATING & AIR CONDITIONING -
STANDARD PROCEDURE).
INSTRUMENT PANEL CENTER
BEZEL
REMOVAL
(1) Disconnect and isolate the battery negative
remote cable.
(2) Using a trim stick (special tool #C-4755) or
equivalent, gently pry out on the edge of the instru-
ment panel center bezel and pull outward (Fig. 5).
(3) Disconnect the wire connector to the HVAC
control.
(4) Remove the instrument panel center bezel from
the vehicle.
INSTALLATION
The HVAC control is mounted to the instrument
panel center bezel. If replacing the center bezel or
the HVAC control, it must be removed from the cen-
ter bezel. Remove the six retaining screws to the
HVAC control.
(1) Connect the wire connectors to the HVAC con-
trol.
(2) Position the center bezel over the retaining
slots and firmly snap the instrument panel center
bezel into place (Fig. 5).
(3) Connect the battery negative remote cable.
INSTRUMENT PANEL
CLUSTER BEZEL
REMOVAL
(1) Disconnect and isolate the battery negative
remote cable.
(2) Remove left end cover.
(3) Using a trim stick (special tool #C-4755) or
equivalent, gently pry up on the power mirror switch.
Disconnect the switch and remove.
(4) Using a trim stick or equivalent, gently pry up
on instrument panel center trim bezel.
(5) Disconnect the HVAC control connector.
(6) Remove one screw from the trim bezel to the
right of the steering column and remove trim by
unsnapping clips.
(7) Remove the one screw from the passenger side
trim bezel and remove trim by unsnapping clips.
(8) Remove five screws to left lower instrument
panel trim.
(9) Remove the four screws to the cluster bezel
(Fig. 6). Using a trim stick or equivalent, gently pry
out the cluster bezel.
(10) If the vehicle is equipped with a Compass
Mini-Trip Computer (CMTC/Traveler), disconnect the
module and then remove the cluster bezel assembly.
Fig. 5 INSTRUMENT PANEL CENTER BEZEL
1 - CENTER BEZEL
2 - INSTRUMENT PANEL
JR
INSTRUMENT PANEL
23 - 75
INSTRUMENT PANEL ASSEMBLY (Continued)
INSTALLATION
(1) Position the cluster bezel and if so equipped,
connect the traveler connector, then snap the cluster
bezel into position (Fig. 6).
(2) Install the four screws to the cluster bezel.
(3) Install the five screws to the left lower instru-
ment panel trim.
(4) Connect the mirror switch connector and firmly
snap it into place.
(5) Install the one screw to the trim bezel to the
right side of the steering column.
(6) Firmly snap into place and then install one
screw to the passenger side trim bezel.
(7) Connect the HVAC control connectors.
(8) Position the center bezel over the retaining
slots and firmly snap instrument panel center bezel
into place.
(9) Install the left end cover.
(10) Connect the battery negative cable.
INSTRUMENT PANEL END
COVER
REMOVAL
(1) Open front door.
(2) Using a trim stick (special tool #C-4755) or
equivalent, disengage clips holding end cover to
instrument panel (Fig. 7).
INSTALLATION
(1) Position end cover over retaining slots and
firmly snap into place (Fig. 7).
(2) Close front door.
Fig. 6 INSTRUMENT PANEL CLUSTER BEZEL
1 - INSTRUMENT PANEL CLUSTER BEZEL
2 - SCREW
Fig. 7 INSTRUMENT PANEL END COVER
1 - LEFT END COVER
2 - INSTRUMENT PANEL
3 - RIGHT END COVER
23 - 76
INSTRUMENT PANEL
JR
INSTRUMENT PANEL CLUSTER BEZEL (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст