Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 667
RIGHT FRONT WHEELHOUSE
SPLASH SHIELD
REMOVAL
(1) Remove the screws and remove the fender trim
(Fig. 10).
(2) Remove right front wheel. (Refer to 22 -
TIRES/WHEELS - REMOVAL)
(3) Remove the eight push pin fasteners, two
screws and remove the splash shield. (Fig. 14).
INSTALLATION
(1) Install the wheelhouse splash shield and install
the eight push pin fasteners and two screws.
(2) Install the wheel assembly. (Refer to 22 -
TIRES/WHEELS - INSTALLATION)
SIDE VIEW MIRROR
REMOVAL
(1) Remove side view mirror cover (Fig. 15).
(2) Remove the door trim panel (Refer to 23 -
BODY/DOOR - FRONT/TRIM PANEL - REMOVAL).
(3) Disconnect power window mirror motor wire
connector, if so equipped.
(4) Disengage wire harness grommet from mirror
flag, if so equipped.
(5) Disconnect manual mirror adjuster from side
mirror cover, if so equipped.
(6) Remove nuts attaching side view mirror to mir-
ror flag (Fig. 16).
(7) Remove side view mirror from vehicle.
INSTALLATION
(1) Feed power mirror wire harness through hole
in mirror flag and seat grommet. Do not pull on wire
harness to seat grommet, if so equipped.
(2) Route adjuster cables through hole in mirror
flag, grommet. Do not pull on cables to seat grommet.
(3) Position side view mirror to vehicle.
(4) Install nuts attaching side view mirror to mir-
ror flag.
Fig. 14 SPLASH SHIELD
1 - PUSH PIN FASTENERS
2 - SPLASH SHIELD
Fig. 15 Side View Mirror Cover
1 - MIRROR FLAG
2 - SIDE VIEW MIRROR COVER
3 - FASTENERS
Fig. 16 Side View Mirror
1 - SIDE VIEW MIRROR
2 - MIRROR FLAG/GLASS CHANNEL
3 - WIRE CONNECTOR
JR
EXTERIOR
23 - 65
(5) Engage push in fastener attaching power mir-
ror wire connector to inner door panel, if so equipped.
(6) Engage power mirror motor wire connector.
(7) Install door trim panel (Refer to 23 - BODY/
DOOR - FRONT/TRIM PANEL - INSTALLATION).
(8) Connect cables to adjuster on side view mirror
cover.
(9) Install side view mirror cover.
SIDE VIEW MIRROR GLASS
REMOVAL
WARNING: ALWAYS WEAR EYE AND HAND PRO-
TECTION WHEN SERVICING THE MIRROR ASSEM-
BLY. FAILURE TO OBSERVE THESE WARNINGS
MAY RESULT IN PERSONAL INJURY FROM BRO-
KEN GLASS.
(1) Carefully pull/pry the broken glass holder from
the mirror assembly.
(2) Disconnect the heated mirror electrical connec-
tors from the terminals on the mirror glass holder, if
equipped.
INSTALLATION
CAUTION: It is important to make sure the motor is
square to the glass holder (attaching fingers) prior
to glass holder attachment, otherwise the glass
holder could be installed incorrectly causing poor
retention and possible repeat failure.
(1) Position the new mirror glass holder to the
mirror assembly.
NOTE: Position the mirror glass holder so that the
moisture drain hole on the mirror glass holder
assembly is facing downward.
(2) Align the mirror glass holder’s attaching fin-
gers to the mirror motor housing.
NOTE: Ensure that the protective rubber cover of
the mirror motor housing is positioned correctly
around the bottom of the fingers area.
(3) Using one hand, firmly press the mirror glass
holder assembly into place while at the same time
supporting the housing assembly from the backside
with the other hand.
NOTE: Pressure must be applied equally over the
center portion of the mirror to engage the mirror
glass holder’s attaching fingers to the correspond-
ing fingers on the housing assembly. One or more
clicks may be heard when finger engagement takes
place.
(4) Verify retention of the mirror glass holder
assembly by gently pulling outward on the mirror
glass holder.
SPOILER
REMOVAL
REMOVAL - JR-41
(1) Remove the decklid cover if necessary. (Refer to
23
-
BODY/DECKLID/HATCH/LIFTGATE/TAIL-
GATE/COVER - REMOVAL)
(2) Remove the four nuts and remove the spoiler
(Fig. 17).
Fig. 17 SPOILER - JR-41
1 - DECKLID
2 - SPOILER
3 - NUTS
23 - 66
EXTERIOR
JR
SIDE VIEW MIRROR (Continued)
REMOVAL - JR-27
(1) Remove the decklid cover if necessary. (Refer to
23
-
BODY/DECKLID/HATCH/LIFTGATE/TAIL-
GATE/COVER - REMOVAL)
(2) Remove the three nuts (Fig. 18).
(3) Using a trim stick or a suitable tool release the
double sided tape attaching spoiler to the decklid
(Fig. 19).
(4) Raising the rear edge of spoiler so the studs
clear the decklid and remove the spoiler.
(5) Clean area by remove all of the double sided
tape and thoroughly clean the area with MOPAR
t
Super Kleen, or equivalent.
INSTALLATION
INSTALLATION - JR-41
(1) Install the spoiler and nuts (Fig. 17).
(2) Tighten nuts to 3 N·m (30 in. lbs.) torque.
(3) Install the decklid cover. (Refer to 23 - BODY/
DECKLID/HATCH/LIFTGATE/TAILGATE/COVER
-
INSTALLATION)
INSTALLATION - JR-27
(1) Clean the area of the decklid and spoiler that
is to be bonded, with an alcohol based cleaner.
(2) Install double sided tape to the spoiler if neces-
sary.
(3) Peel the backing from tape on the bottom side
of spoiler (Fig. 19).
(4) Position spoiler on the decklid aligning studs to
holes and spoiler into position.
(5) Press firmly on the leading edge of spoiler to
assure adhesion.
(6) Raise decklid and install nuts attaching spoiler
to the decklid. Tighten nuts to 5 N·m (45 in. lbs.)
torque (Fig. 18).
(7) Close decklid.
TAPE STRIPE
REMOVAL - ADHESIVES
(1) Mark reference points before removing.
(2) Using a heat gun gently apply heat in a circu-
lar motion to loosen the adhesive bond.
(3) Using the trim stick C 4755 or equivalent, lift
up and peel away badging /tape from panel, using a
heat gun as you go.
(4) Clean off all traces of adhesive from the pan-
el(s) with a general purpose adhesive remover.
INSTALLATION - ADHESIVES
(1) Clean panel surface with isopropyl alcohol.
(2) Remove paper carrier and align badging/tape to
reference points or adjacent panel.
(3) Install and press securely, using a plastic
spreader to eliminate all air bubbles.
(4) Remove top protective carrier.
(5) Clean away any reference points.
Fig. 18 SPOILER ATTACHING NUTS
1 - ATTACHING NUT (S)
2 - DECKLID
Fig. 19 SPOILER
1 - SPOILER ASSEMBLY
2 - DOUBLE BACK TAPE
3 - DECK LID
JR
EXTERIOR
23 - 67
SPOILER (Continued)
HOOD
TABLE OF CONTENTS
page
page
ADJUSTER BUMPER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
. . . . . . . . . . . . . . . . . . . . . . . . . 68
HINGE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
. . . . . . . . . . . . . . . . . . . . . . . . . 68
HOOD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
. . . . . . . . . . . . . . . . . . . . . . . . . 69
LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
. . . . . . . . . . . . . . . . . . . . . . . . . 69
LATCH RELEASE CABLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
. . . . . . . . . . . . . . . . . . . . . . . . . 70
PROP ROD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
. . . . . . . . . . . . . . . . . . . . . . . . . 70
ADJUSTER BUMPER
REMOVAL
(1) Release hood latch and open hood.
(2) Rotate hood adjuster bumper counterclockwise.
(3) Remove hood adjuster bumper from headlamp
reinforcement (Fig. 1).
INSTALLATION
(1) Ensure that hood overslam bumpers proper
position (Fig. 2).
(2) Start hood adjuster bumper into headlamp
reinforcement (Fig. 1).
(3) Rotate hood adjuster bumper clockwise. Adjust
hood adjuster bumper to achieve a hood height that
is flush across the top surfaces along fenders.
(4) Close hood.
HINGE
REMOVAL
(1) Support hood on the side that requires hinge
replacement.
(2) Mark hinge attachment locations with a grease
pencil or other suitable device to aid installation.
(3) Remove cowl cover (Refer to 23 - BODY/EXTE-
RIOR/COWL GRILLE - REMOVAL).
(4) Remove bolts attaching hood to hinge.
(5) Remove bolts attaching hood hinge to load
beam inner and remove hinge from vehicle.
INSTALLATION
(1) If necessary, paint new hinge before installa-
tion.
(2) Place hinge in position on vehicle.
Fig. 1 HOOD ADJUSTER BUMPER
1 - HOOD ADJUSTER BUMPER
2 - HEADLAMP REINFORCEMENT
Fig. 2 HOOD OVERSLAM BUMPER
1 - OVERSLAM BUMPER
2 - HOOD
23 - 68
HOOD
JR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст