Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 668
(3) Install bolts to attach hood hinge to load beam
inner.
(4) Install bolts to attach hood to hinge.
(5) Align all marks and secure bolts.
(6) Tighten bolts to 28 N·m (20 ft. lbs.) torque.
(7) The hood should be aligned to 4 mm (0.160 in.)
gap to the front fenders and flush across the top sur-
faces along fenders. Shims can be added or removed
under hood hinge to achieve proper hood height.
(8) Install cowl cover (Refer to 23 - BODY/EXTE-
RIOR/COWL GRILLE - INSTALLATION).
(9) Verify hood latch operation. Adjust as necessary.
HOOD
REMOVAL
(1) Open hood.
(2) Mark outline of hinges on inside of hood to aid
installation.
(3) Remove the top bolts attaching hood to hinge
and loosen the bottom bolts until they can be
removed by hand.
(4) With assistance from a helper at the opposite
side of the vehicle to support the hood, remove bot-
tom bolts attaching hood to hinge.
(5) Remove the hood from the vehicle.
INSTALLATION
(1) With assistance from a helper, place hood in
position on vehicle.
(2) Install bottom bolts to attach hood to hinge fin-
ger tight.
(3) vccInstall top bolts to attach hood to hinge fin-
ger tight.
(4) Position bolts at outline marks and tighten
bolts. The hood should be aligned to 4 mm (0.160 in.)
gap to the front fenders and flush across the top sur-
faces along fenders.
(5) Connect under hood lamp wire connector to
engine compartment wire harness, if equipped.
(6) Verify hood latch operation and alignment.
Adjust as necessary.
LATCH
REMOVAL
(1) Release hood latch and open hood.
(2) Support hood on prop rod.
(3) Mark outline of hood latch on radiator support
crossmember with a grease pencil or other suitable
device to aid installation.
(4) Remove nuts attaching hood latch to upper
radiator support crossmember (Fig. 3).
(5) Remove hood latch from vehicle.
(6) Disengage remote release cable from hood latch
(Fig. 4).
INSTALLATION
(1) Engage remote release cable into hood latch
(Fig. 4).
(2) Position hood latch on vehicle.
(3) Install nuts attaching hood latch onto upper
radiator support crossmember.
(4) Tighten nut to 28 N·m (20 ft. lbs.) torque.
(5) Verify operation. Adjust as necessary.
LATCH RELEASE CABLE
REMOVAL
(1) Remove hood latch (Refer to 23 - BODY/HOOD/
LATCH - REMOVAL).
Fig. 3 HOOD LATCH
1 - HOOD LATCH
2 - HOOD RELEASE CABLE
3 - RADIATOR SUPPORT CROSSMEMBER
Fig. 4 HOOD LATCH RELEASE CABLE
1 - HOOD LATCH
2 - HOOD RELEASE CABLE
JR
HOOD
23 - 69
HINGE (Continued)
(2) Remove left front cowl trim panel.
(3) Remove screws attaching hood release handle
to inner cowl panel (Fig. 5).
(4) Release clips attaching hood release cable to
left inner frame rail (Fig. 6).
(5) Disengage rubber grommet at lower dash panel.
(6) Disengage push-in fastener attaching hood
release cable to dash panel.
(7) Remove hood release cable from vehicle.
INSTALLATION
(1) Route hood release cable through hole in lower
dash panel and along inner frame rail.
(2) Engage rubber grommet to lower dash panel.
(3) Engage push-in fastener attaching hood release
cable to lower dash panel.
(4) Install screws attaching hood release cable
handle to inner cowl panel.
(5) Tighten screws to 1.8 N·m (16 in. lbs.) torque.
(6) Install left front cowl trim panel.
(7) Engage hood release cable into clips along
inner frame rail (Fig. 6).
(8) Install hood latch (Refer to 23 - BODY/HOOD/
LATCH - INSTALLATION).
PROP ROD
REMOVAL
(1) Release hood latch and open hood.
CAUTION: Do not place prop-rod or substitute against
outer hood panel, damage to exterior finish will result.
(2) Prop hood open using a length of wooden dowel
rod, ex (Broomstick).
(3) Disengage prop-rod from retainer attaching
prop-rod to radiator closure panel (Fig. 7).
(4) Remove prop-rod from vehicle.
INSTALLATION
CAUTION: Do not place prop-rod or substitute against
outer hood panel, damage to exterior finish will result.
(1) Place prop-rod into position.
(2) Engage prop-rod from retainer attaching prop-
rod to radiator closure panel.
(3) Remove temporary hood prop rod.
(4) Close hood.
Fig. 5 Hood Release Cable Handle
1 - COWL PANEL
2 - HOOD RELEASE CABLE
3 - HOOD RELEASE HANDLE
Fig. 6 Hood Release Cable Routing
1 - FRAME RAIL
2 - UPPER RADIATOR SUPPORT CROSSMEMBER
3 - HOOD RELEASE CABLE
Fig. 7 Hood Prop Rod
1 - RADIATOR CLOSURE PANEL
2 - HOOD PROP-ROD
3 - CLIP
4 - RADIATOR SUPPORT CROSSMEMBER
5 - RETAINER
23 - 70
HOOD
JR
LATCH RELEASE CABLE (Continued)
INSTRUMENT PANEL
TABLE OF CONTENTS
page
page
CD CHANGER TRIM BEZEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
. . . . . . . . . . . . . . . . . . . . . . . . . 71
GLOVE BOX
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
. . . . . . . . . . . . . . . . . . . . . . . . . 72
GLOVE BOX LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
. . . . . . . . . . . . . . . . . . . . . . . . . 72
INSTRUMENT PANEL ASSEMBLY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
. . . . . . . . . . . . . . . . . . . . . . . . . 73
INSTRUMENT PANEL CENTER BEZEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
. . . . . . . . . . . . . . . . . . . . . . . . . 75
INSTRUMENT PANEL CLUSTER BEZEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
. . . . . . . . . . . . . . . . . . . . . . . . . 76
INSTRUMENT PANEL END COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
. . . . . . . . . . . . . . . . . . . . . . . . . 76
INSTRUMENT PANEL INBOARD BEZEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
. . . . . . . . . . . . . . . . . . . . . . . . . 77
INSTRUMENT PANEL OUTBOARD BEZEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
. . . . . . . . . . . . . . . . . . . . . . . . . 77
INSTRUMENT PANEL TOP COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
. . . . . . . . . . . . . . . . . . . . . . . . . 78
LEFT LOWER INSTRUMENT PANEL TRIM
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
. . . . . . . . . . . . . . . . . . . . . . . . . 78
LEFT LOWER INSTRUMENT SILENCER PANEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
. . . . . . . . . . . . . . . . . . . . . . . . . 79
RIGHT LOWER SILENCER PANEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
. . . . . . . . . . . . . . . . . . . . . . . . . 79
RIGHT INSTRUMENT PANEL TRIM BEZEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
. . . . . . . . . . . . . . . . . . . . . . . . . 80
RIGHT LOWER INSTRUMENT PANEL TRIM
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
. . . . . . . . . . . . . . . . . . . . . . . . . 80
KICK SHIELD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
. . . . . . . . . . . . . . . . . . . . . . . . . 81
DASH PANEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
. . . . . . . . . . . . . . . . . . . . . . . . . 81
CD CHANGER TRIM BEZEL
REMOVAL
(1) Using a trim stick (special tool #C-4755) or
equivalent, gently pry out on the CD changer trim
bezel and remove from the vehicle (Fig. 1).
INSTALLATION
(1) Position CD changer trim bezel over the retain-
ing slots and firmly snap into place (Fig. 1).
GLOVE BOX
REMOVAL
(1) Open glove box.
(2) Push in on sides of glove box bin and lower
door.
(3) Pivot glove box downward and disengage hinge
hooks from instrument panel.
(4) Remove glove box.
Fig. 1 CD CHANGER TRIM BEZEL
1 - CD CHANGER TRIM BEZEL
2 - CD CHANGER
JR
INSTRUMENT PANEL
23 - 71
INSTALLATION
(1) Place glove box in position.
(2) Engage hinge hooks into instrument panel and
pivot glove box upward.
(3) Push in sides of glove box bin and snap glove
box assembly into instrument panel.
(4) Close glove box door.
GLOVE BOX LATCH
REMOVAL
(1) Open glove box.
(2) Push in on sides of glove box bin and lower
door.
(3) Pivot glove box downward and disengage hinge
hooks from instrument panel.
(4) Remove glove box.
(5) Remove the assembly screws.
(6) Disassemble the glove box.
(7) Separate the latch from the glove box assembly.
INSTALLATION
(1) Install the latch onto the glove box assembly.
(2) Assemble the glove box.
(3) Install the assembly screws.
(4) Engage hinge hooks into instrument panel and
pivot glove box upward.
(5) Push in sides of glove box bin and snap glove
box assembly into instrument panel.
(6) Close glove box door.
INSTRUMENT PANEL
ASSEMBLY
REMOVAL
The Instrument Panel and HVAC assemblies are
removed together as one assembly. If service is
required to the individual unit, separation might be
required.
(1) Recover the A/C refrigerant (Refer to 24 -
HEATING & AIR CONDITIONING - STANDARD
PROCEDURE).
(2) Partially drain the coolant (Refer to 7 - COOL-
ING/ENGINE - STANDARD PROCEDURE).
(3) Remove one bolt retaining the A/C lines to the
right strut tower.
(4) Remove the two top HVAC housing retaining
nuts in engine compartment (Fig. 2).
(5) Hoist vehicle and remove the lower HVAC
housing retaining nut.
(6) Lower vehicle from hoist.
(7) Remove the driver and passenger seats (Refer
to 23 - BODY/SEATS/SEAT - REMOVAL).
(8) Disconnect and isolate the battery negative
remote cable.
(9) Remove one screw to shift knob and transmis-
sion range indicator bezel from floor console.
(10) Remove floor center console. Remove two
mounting screws in the front and two mounting
screws inside console storage bin (Refer to 23 -
BODY/INTERIOR/FLOOR CONSOLE - REMOVAL).
(11) Remove the amplifier (Refer to 8 - ELECTRI-
CAL/AUDIO/AMPLIFIER - REMOVAL).
(12) Using a trim stick (special tool #C-4755) or
equivalent, gently pry out on the left and right rear
floor heat ducts and remove (Fig. 3).
Fig. 2 HVAC HOUSING RETAINING NUTS
1 - BULKHEAD
2 - EXPANSION VALVE
3 - NUT
Fig. 3 REAR HEAT DUCT
1 - REAR HEAT DUCT
2 - LOCATING CLIP
23 - 72
INSTRUMENT PANEL
JR
GLOVE BOX (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст